Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Re: Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Postby Alominer » 24 Feb 2018, 18:29

Спустя долгих лет службы навернулся мой миник. При включении появляется надпись ASUS, гаснет и дальше чёрный экран. Примерно через минуту опять появляется надпись и далее по циклу.
Подцепился консолью к UART, вот что пишет:
| +
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.24 17:04:52 =~=~=~=~=~=~=~=~=~=~=~=
hello_world!
hello_world!
55228800 wwaaiittEPHY: 8211CL

[HDMI]: Set I2C Speed = 50 kHz

[HDMI]: Chk_HotPlug() TV is not connected.

[HDMI]: Read_EDID abort, HDMI cable plug off.

[HDMI]: TV is not connected.

Change to PAL system (0xfc3fff80)


REALTEK ROM Monitor, Revision 0109.0305.0018.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Jun 8 2011 20:36:44 /0109.0305.0018

MAC address = 20.cf.30.d5.cb.de

Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision = 0x93 / 0x78

Endianness = Little
Flash memory size = 512 MByte

SDRAM size = 256 MByte

First free SDRAM address = 0x800ad000


Press 'ESC' to Monitor mode

Linux Kernel:

FW Image from 0xa2020000, to 0x80100000, size=0x450086

decrypt from 0xa2020000 to 0x80100000, len:0x450086

Audio FW:

FW Image from 0xa2480000, to 0x81b00000, size=0x1e2458

decrypt from 0xa2480000 to 0x81b00000, len:0x1e2458

Video FW:

FW Image from 0xa2680000, to 0x81d80000, size=0x1bc418

decrypt from 0xa2680000 to 0x81d80000, len:0x1bc418

5280Go 5280Go
HDMI Raw Enable: MPG AC3 DTS AAC DDP WMAPRO MLP

SPDIF Raw Enable: MPG AC3 DTS AAC DDP WMAPRO MLP

Force 2ch Format: DTS DTSHD AC3 DDP MLP AAC WMAPROSC P

U_C
LNKo9 Po0Kw=e0r .O01n2 Musesci.c



go 0x80100000 mtdparts=rtk_nand:239232k,62208k(/),196608k(/usr/local/etc),26240k rootfstype=squashfs root=31:01

Reset Ethernet Mac.




Address = 0x80100000


Realtek LINUX started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 2 UARTs.
System CPU uses external timer interrupt.
Bootloader version: 0109.0305.0018. This version string is of new format.
The information of this board: Company ID:0x109 CPU ID: 0x33 Board ID: 0x1090305
Ethernet Mac address: 20.CF.30.D5.CB.DE
Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x20000000
Linux version 2.6.12.6-VENUS (root@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.00-20051020) #2 Thu Sep 29 02:59:03 CST 2011

audio addr: 1b00000

CPU revision is: 00019378

Determined physical RAM map:

memory: 00100000 @ 00000000 (usable)

memory: 00471000 @ 00100000 (reserved)

memory: 0158f000 @ 00571000 (usable)

memory: 00500000 @ 01b00000 (reserved)

memory: 0e000000 @ 02000000 (usable)

show info: max_low_pfn:65536

show info: min_low_pfn:1393

ZONE: DMA, PFN: 0

ZONE: Normal, PFN: 53248

ZONE: DVR, PFN: 4096

Built 1 zonelists

Kernel command line: mtdparts=rtk_nand:239232k,62208k(/),196608k(/usr/local/etc),26240k rootfstype=squashfs root=31:01 console=ttyS0,115200n8r ip=10.10.111.202::10.10.111.1:255.255.255.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

RBUS DC SYS debug interrupt handler is inserted.

PID hash table entries: 512 (order: 9, 8192 bytes)

Estimate value: CPU frequency 499.52 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 249240k/252476k available (3572k kernel code, 3188k reserved, 695k data, 148k init, 0k highmem)

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction... available.

========== board id: 1090305 ==========

[INFO] neptune mode...

boot_param value: a0002800

mode: 0

Set logo mode to PAL

mode: 1

size: 990

color1: 0x808010

color2: 0x8080a2

color3: 0x8080eb

color4: 0x808059

NET: Registered protocol family 16

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

pci_scan_single_device, devfun = 0

PCI: Found 0000:00:00.0 [10ec/8176] 000280 00

pci_scan_single_device, devfun = 8

pci_scan_single_device, no dev exists

pci_scan_single_device, devfun = 16

pci_scan_single_device, no dev exists





***************** se init module *********************




se init module major number = 254

instcnt=0, u64cnt=0, u64IssuedInstCnt=0

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

[MCP] Info, mcp device detected ...

Hello, Realtek TLB Mapper

AllocBP size: 589824 order: 8

<<<DVR FREE AREA>>>

0: 0

1: 0

2: 0

3: 0

4: 0

5: 0

6: 0

7: 0

8: 1

Addr: 81a00000, order: 8

9: 1

Addr: 81800000, order: 9

10: 0

11: 1

Addr: 81000000, order: 11

12: 11

Addr: 8c000000, order: 12

Addr: 8b000000, order: 12

Addr: 8a000000, order: 12

Addr: 89000000, order: 12

Addr: 88000000, order: 12

Addr: 87000000, order: 12

Addr: 86000000, order: 12

Addr: 85000000, order: 12

Addr: 84000000, order: 12

Addr: 83000000, order: 12

Addr: 82000000, order: 12

<mtp module> insert mtpfs module OK

squashfs: v-------------------
Audio Version = 449768 (jupiter)
Common Version = 448485
Binary src compiled at Sep 10 2012 09:41:49
Note =
-----------e-------
rsion 3.1 (2006/08/19) Phillip Lougher

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.

YAFFS Driver Rev:291473 (2010-01-14)

YAFFS Driver is successfully installing.

Initializing Cryptographic API

pci_hotplug: PCI Hot Plug PCI Core version: 0.5

fakephp: Fake PCI Hot Plug Controller Driver

Generic RTC Driver v1.07

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

ttyS1 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2.5-NAPI

e1000e: Copyright(c) 1999 - 2009 Intel Corporation.

this Jupiter eth RX_OFFSET = 0x0

8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)

MAC address = 0x20.CF.30.D5.CB.DE

eth0: RTL-8139C+ at 0xb8016000, 20:cf:30:d5:cb:de, IRQ 2

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

NET: Registered protocol family 24

Linux video capture interface: v1.00

VenusSFC MTD init...

NOR flash support list ..

(V) MD_WRITE support.

(X) MD_READ support.

(V) HWSEMA support.

(V) AUTO_HW_POLL support.

(X) 4Bytes mode support.

(X) Sfc_delay support.

serial flash inaccessible

physmap flash device: 20000000 at ffd00000

Failed to ioremap

New patch -- change oob layout [rtk_nand_init]

Realtek NAND Flash Driver Rev:359129 (2011-05-16)

(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ

(X)NAND_READ_SKIP_UPDATE_BBT

cp_hotplug

[rtk_nand_read_id] Read ID result as follow

ID0[0xad]

ID1[0xdc]

ID2[0x10]

ID3[0x95]

ID4[0x54]

ID5[0xad]

[rtk_nand_read_id] Read ID result as follow

ID0[0x0]

ID1[0x0]

ID2[0x0]

ID3[0x0]

ID4[0x0]

ID5[0x0]

One HY27UF084G2B chip has 1 die(s) on board

nand part=HY27UF084G2B, id=addc1095, device_size=536870912, chip_size=536870912, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

Congratulation!! No BBs in this Nand.

4 cmdlinepart partitions found on MTD device rtk_nand

RTK: using dynamic nand partition

Creating 4 MTD partitions on "rtk_nand":

0x00000000-0x0e9a0000 : "Partition_000"

0x0e9a0000-0x12660000 : "/"

0x12660000-0x1e660000 : "/usr/local/etc"

0x1e660000-0x20000000 : "Partition_003"

0x00000000-0x20000000 : "disc"

Realtek Nand Flash Driver is successfully installing.

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

Initializing USB MTP/PTP driver...

usbcore: registered new driver usb-mtp

USB MTP/PTP support registered.

mice: PS/2 mouse device common for all mice

i2c /dev entries driver

[I2C0] i2c speed changed to 100 KHz

I2C0 Bus Status Check.... OK

=========================

= VER : 2.1b

=========================

= PHY : 0

= MODEL: Jupiter

= SPD : 100

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 32

= RX FIFO DEPTH : 32

= FIFO THRESHOLD: 4

= BUS JAM RECORVER 3: ON

= NON STOP WRITE : ON

= GPIO RW SUPPORT : ON

=========================

[I2C1] i2c speed changed to 100 KHz

I2C1 Bus Status Check.... OK

=========================

= VER : 2.1b

=========================

= PHY : 1

= MODEL: Jupiter

= SPD : 100

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 32

= RX FIFO DEPTH : 32

= FIFO THRESHOLD: 4

= BUS JAM RECORVER 3: ON

= NON STOP WRITE : ON

= GPIO RW SUPPORT : ON

=========================

cec_core_init, register cec_bus 80502850

mars cec module init

register cec driver 'mars_cec' (80502aac)

register cec device 'mars_cec' (805029e8) to cec0

probe : cec_dev 'mars_cec' (805029e8), cec_drv 'mars_cec' (80502aac)

Open Jupiter CEC

NET: Registered protocol family 2

IP: routing cache hash table of 2048 buckets, 16Kbytes

TCP established hash table entries: 16384 (order: 5, 131072 bytes)

TCP bind hash table entries: 16384 (order: 4, 65536 bytes)

TCP: Hash tables configured (established 16384 bind 16384)

NET: Registered protocol family 1

NET: Registered protocol family 17

Realtek Venus Power Management, (c) 2006 Realtek Semiconductor Corp.

cp_open

alloc rings cp->rxdesc_buf =0xa0572000 , cp->ring_dma=0x572000

init_hw


eth0: Set multicast.

jupiter 1g

init_hw finished


eth0: Set multicast.


eth0: Set multicast.

RTK rtc can work.


eth0: Set multicast.

IP-Config: Complete:

device=eth0, addr=10.10.111.202, mask=255.255.255.0, gw=10.10.111.1,

host=10.10.111.202, domain=, nis-domain=(none),

bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

SCPU_CLK90K=3.065 sec.

Freeing prom memory: 0kb freed

Freeing unused kernel memory: 148k freed

Welcome to Realtek Linux

Please press Enter to activate this console. yaffs: dev is 32505858 name is "mtdblock2"

yaffs: Attempting MTD mount on 31.2, "mtdblock2"

------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

Starting INET services....
------flush priority: 10

flush_page_cache: do flush...

libata version 1.12 loaded.

sata driver initial...2011/07/22 14:20

JUPITER(Ver.C/D): one port supported

mars_init_sata(1297)dev_addr:c00707d0

Realtek Card-Reader Driver Rev:161767 (2011-07-11 16:55)

Realtek SD/MMC Controller Driver is successfully installing.


ata_device_add(4888)probe begin

scsi0 : SATA_DRV

sata dma reset

__mars_sata_phy_reset(883)ap->port_no:0

jupiter mdio setting enable

Running dvdplayer with RootApp
set corepath: /tmp/hdd/volumes/HDD1/

RootApp AVHDD version...
***256MB version...

enter 2nd case...
pli initialization...
Memory address 0x40000000

clear pli setting....

================================================
================================================
root execute DvdPlayer...
================================================
================================================
sata1: reset phy again!

sata phy reset

IN : /tmp/ramfs/smb
downloader 0 starts, 0x19f8478
downloader 1 starts, 0x19f8588
finish default module register
finish rtse module register
finish devmem module register
finish ps2mouse module register
[Dlna DMR] this is GDlnaMediaRendererAP
CMD: mkdir -p /tmp/netb/smb
In my system...
CMD: mkdir -p /tmp/smb
In my system...
CMD: ifconfig > /tmp/netb/samba_my_ip
In my system...
CMD: mkdir -p /tmp/nfsmounts
In my system...
(t=1024) preloadSoLib: initialize...
(t=1024) preloadSoLib: exit
GrandMa Revision: 380582
!!!BootUP!!!
Bootup t1 = 1519481165.207 sec
In my system...
Bootup t2 = 1519481165.233 sec






WARNING WARNING WARNING m_db_manage_flag_cnt = -1





DB FILENAME = /tmp/ramfs/Setup
[DataObject.cpp 550] ---- Create new DB Start -/usr/local/etc/dvdplayer/Setup----
WatchDog does not receive signal for 2 seconds, value: 0
[DataObject.cpp 669] database compact ok!!
[DataObject.cpp 575] ---- Create new DB End -----
[DataObject.cpp 440]DB Develop Version same . Don't be upgrade.
[DataObject.cpp 479]DB Version same . Don't be upgrade.



m_BookMark_Size=4096 m_Signature_Size=16


org change count = 0 , total ch***256MB version...

ange count = 189
pli initialization...
Memory address 0x40000000

Bootup t3 = 1519481165.647 sec
***************** se open: queue = 0 *********************

--- RtkBootUP(93 ***************** se open: initialized = 0 *********************

): 6.933 sec
arch/mips/realtek-boards/drivers/se.c, 614: offset = 0, se_devices = 8d038000

arch/mips/realtek-boards/drivers/se.c, 624: offset = 0

arch/mips/realtek-boards/drivers/se.c, 668: length = 20480

arch/mips/realtek-boards/drivers/se.c, 669: offset = 218333184

arch/mips/realtek-boards/drivers/se.c, 676: offset = 218333184

arch/mips/realtek-boards/drivers/se.c, 614: offset = 98316, se_devices = 8d038000

arch/mips/realtek-boards/drivers/se.c, 624: offset = 402702336

arch/mips/realtek-boards/drivers/se.c, 668: length = 4096

arch/mips/realtek-boards/drivers/se.c, 669: offset = 402702336

arch/mips/realtek-boards/drivers/se.c, 676: offset = 402702336

In my system...
filename is ./directfbrc
filename is /usr/local/etc/dvdplayer/directfbrc
filename is //.directfbrc
filename is /media/123/1185/avhdd/system/branch_src_sharedMemory_integration/Platform_L+++ ALLOC index: 2048 order: 9

ib/Graphics/Dire1. start remap DVR zone 81800000(805a3000) 512...

ctFB/build/etc/directfbrc.dvdplayer-directfb
filename is //.directfbrc.dvdplayer-directfb
finish mouse init in DirectFBInit
map_done is 512...

[AUDIO] Receive debug memory address x 0x81ce9688 !
[AUDIO] Debug memory address *x is 0x0d858600 !

SetLPrintBuffer: header address = 0x00000+000
++ ALLOC index: 2560 order: 7

1. start remap DVR zone 81a00000(805a7000) 128...

map_done is 128...

Video DebugMem PVIDEO_RPC_SetDebugMemory Called!+++ ALLOC index: 2688 order: 7

hysical Address 1. start remap DVR zone 81a80000(805a8000) 128...

= 0xd858400
map_done is 128...

+++ ALLOC index: 0 order: 8

1. start remap DVR zone 81000000(80593000) 256...

map_done is 256...

[AUDIO WARNING]
no more memory , do Remote Malloc. Size 0x00186000
667 loadThemeSetting resource.cpp
No THEMESET_INI exists
-=- create FT engine for ./Resource/font/arial.ttf
[VoutUtil.cpp:1~~SetVideoStandard: fmt 7 ped 1 prog 0
+++ ALLOC index: 512 order: 9

78,SetVideoStand1. start remap DVR zone 81200000(80597000) 512...

ard] 1, standard = 7
[VoutUtil.cpp:179,SetVideoStandard] 2, enProg = 0

(TVE) TVE_DAC_mode 0!! ~~comp 1, ch2 0
~~TVE standard#

[VoutUtil.cpp:180,SetVideoStandard] 3, enDIF = 1
[VoutUtil.cpp:181,SetVideoStandard] 4, enCompRGB = 0
[VoutUtil.cpp:182,SetVideoStandard] 5, pedType = 1
[VoutUtil.cpp:183,SetVideoStandard] 6, dataInt0 = 4
[VoutUtil.cpp:184,SetVideoStandard] 7, dataInt1 = 0
WARNING[2]:TVE i-underflow @ line 0
WARNING[2]:TVE p-underflow @ line 0
WARNING[2]:TVE h-underflow @ line 0
map_done is 512...

[AUDIO WARNING]
no more memory , do Remote Malloc. Size 0x00186000
+++ ALLOC index: 1024 order: 9

1. start remap DVR zone 81400000(8059b000) 512...

map_done is 512...

[VoutUtil.cpp:285,SetVideoStand[AUDIO WARNING]
[A] malloc 0x00020000, but it'll malloc 0x00040000
+++ ALLOC index: 45056 order: 11

ard] 8, bHDMI =1. start remap DV-------------------
Audio Version = 449768 (jupiter)
Common Version = 448485
Binary src compiled at Sep 10 2012 09:41:49
Note =
------------R-------
ClassifyBonding 0x00000302, num = 0x00000005 DD (DD)
[AUDIO WARNING] [_AO_get_first_valid_chIDX invalid]
zone 8c000000(806f3000) 2048...

1
map_done is 18...

will run direct_initialize
<<<<<< core_parts[i] = clipboard_core >>>>>>>
<<<<<< core_parts[i] = colorhash_core >>>>>>>
<<<<<< core_parts[i] = surface_core >>>>>>>
<<<<<< core_parts[i] = system_core >>>>>>>
start[0-3] = {70+++ ALLOC index: 47104 order: 11

01a500, 7001a5041. start remap DVR zone 8c800000(80703000) 2048...

, 7001a508, 7001a50c}
end[0-3] = {7001a510, 7001a514, 7001a518, 7001a51c}
map_done is 132...

+++ ALLOC index: 40960 order: 11

1. start remap DVR zone 8b000000(806d3000) 2048...

map_done is 132...

<<<<<< core_parts[i] = input_core >>>>>>>
init ps2mouse success, the device_file is /dev/input/mice
<<<<<< core_parts[i] = graphics_core >>>>>>>
<<<<<< core_pa--- FREE index: 40960 order: 11

rts[i] = screen--- FREE index: 47104 order: 11

_core >>>>>>>
<<<<<< core_parts[i] = layer_core >>>>>>>
<<<<<< core_parts[i] = wm_core >>>>>>>
+fusion_arena_exit
+ps2mouse.c/driver_close_device:
-ps2mouse.c/driver_close_device:
free_sb2_zone_and_unlock: WARNING! Invalid zone idx -1(>=4)
free_sb2_zone_and_unlock: WARNING! Invalid zone idx -1(>=4)
DG_DirectFBCreate: DirectFBCreate() failed. err=Not supported!
DG_DirectFBCreate(DirectGraphicsOnBoard2.cpp, 659 ): ASSERT(0) failed
WatchDog does not receive signal for 2 seconds, value: 0
sata1: reset phy again!

sata phy reset

WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
sata1: phy reset timeout!

sata1: no device found (phy stat 00000000)

__mars_sata_phy_reset(942)

sata1: ata_bus_probe failed

WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0
WatchDog does not receive signal for 2 seconds, value: 0

и постоянно повторяет последнюю строку - WatchDog does not receive signal for 2 seconds, value: 0

Пробовал прошиться на сток по инструкции - флешка + спичкой зажал кнопку. На экране только надпись Preparing for update и после 10минут ожидания никаких изменений.
Вывод с консоли:
| +
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.24 17:06:39 =~=~=~=~=~=~=~=~=~=~=~=
я hello_world!
hello_world!
55228800 wwaaiittEPHY: 8211CL

[HDMI]: Set I2C Speed = 50 kHz

[HDMI]: Chk_HotPlug() TV is not connected.

[HDMI]: Read_EDID abort, HDMI cable plug off.

[HDMI]: TV is not connected.

Change to PAL system (0xfc3fff80)


REALTEK ROM Monitor, Revision 0109.0305.0018.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Jun 8 2011 20:36:44 /0109.0305.0018

MAC address = 20.cf.30.d5.cb.de

Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision = 0x93 / 0x78

Endianness = Little
Flash memory size = 512 MByte

SDRAM size = 256 MByte

First free SDRAM address = 0x800ad000


Press 'ESC' to Monitor mode

Rescue kernel in FLASH, total size = 0xee927



seg.1 addr 0xa0a05a4c, size = 0xee927



seg.2 addr 0x0, size = 0x0

copy rescue0: from a0a05a4c to 81000000, len = ee927

decrypt from 0x81000000 to 0x83000000, len:0xee927

decompressing rescue: from 83000000 to 80100000: size = ee927

lzma finished

decompressing rescue done

go 0x80100000

Reset Ethernet Mac.




Address = 0x80100000


Realtek LINUX started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 1 UART.
System CPU uses external timer interrupt.
Bootloader version: 0109.0305.0018. This version string is of new format.
The information of this board: Company ID:0x109 CPU ID: 0x33 Board ID: 0x1090305
Ethernet Mac address: 20.CF.30.D5.CB.DE
Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x20000000
Linux version 2.6.12.6-VENUS (root@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.00-20051020) #5 Sat May 14 02:04:56 CST 2011

**************************************************************

You didn't specify audio image address, use default instead...

**************************************************************

audio addr: 0

CPU revision is: 00019378

Determined physical RAM map:

memory: 00100000 @ 00000000 (usable)

memory: 0029c000 @ 00100000 (reserved)

memory: 019e4000 @ 0039c000 (usable)

memory: 00280000 @ 01d80000 (reserved)

memory: 0e000000 @ 02000000 (usable)

show info: max_low_pfn:65536

show info: min_low_pfn:924

ZONE: DMA, PFN: 0

ZONE: Normal, PFN: 53248

ZONE: DVR, PFN: 4096

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8r ip=10.10.111.202::10.10.111.1:255.255.255.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 512 (order: 9, 8192 bytes)

Estimate value: CPU frequency 499.53 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 253676k/256912k available (1873k kernel code, 3188k reserved, 283k data, 444k init, 0k highmem)

Warning! Unknown board id.

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction... available.

Linux NoNET1.0 for Linux 2.6

SCSI subsystem initialized

usbcore: registered new driver hub

GPIO: register IRQ 3... (Success)





***************** se init module *********************




se init module major number = 254

instcnt=0, u64cnt=0, u64IssuedInstCnt=0

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

Hello, Realtek TLB Mapper

AllocBP size: 589824 order: 8

<<<DVR FREE AREA>>>

0: 0

1: 0

2: 0

3: 0

4: 0

5: 0

6: 0

7: 0

8: 0

9: 1

Addr: 81c00000, order: 9

10: 1

Addr: 81800000, order: 10

11: 1

Addr: 81000000, order: 11

12: 11

Addr: 8c000000, order: 12

Addr: 8b000000, order: 12

Addr: 8a000000, order: 12

Addr: 89000000, order: 12

Addr: 88000000, order: 12

Addr: 87000000, order: 12

Addr: 86000000, order: 12

Addr: 85000000, order: 12

Addr: 84000000, order: 12

Addr: 83000000, order: 12

Addr: 82000000, order: 12

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x0

NTFS driver 2.1.28 [Flags: R/O].

Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

VenusSFC MTD init...

NOR flash support list ..

(V) MD_WRITE support.

(X) MD_READ support.

(V) HWSEMA support.

(V) AUTO_HW_POLL support.

(X) 4Bytes mode support.

(X) Sfc_delay support.

serial flash inaccessible

physmap flash device: 20000000 at ffd00000

Failed to ioremap

Realtek NAND Flash Driver Rev:349905 (2011-02-10)

(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ

(X)NAND_READ_SKIP_UPDATE_BBT

[rtk_nand_read_id] Read ID result as follow

ID0[0xad]

ID1[0xdc]

ID2[0x10]

ID3[0x95]

ID4[0x54]

ID5[0xad]

[rtk_nand_read_id] Read ID result as follow

ID0[0x0]

ID1[0x0]

ID2[0x0]

ID3[0x0]

ID4[0x0]

ID5[0x0]

One HY27UF084G2B chip has 1 die(s) on board

nand part=HY27UF084G2B, id=addc1095, device_size=536870912, chip_size=536870912, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

Congratulation!! No BBs in this Nand.

RTK: using the whole nand as a partitoin

Realtek Nand Flash Driver is successfully installing.

[usb_param] setting for jupiter

#######[cfyeh-debug] USBPHY_Register_Setting(893) jupiter D

[usb_param] set port two for host!

#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 1

#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 1

#@# cfyeh-debug USBPHY_SetReg_Default_39(417) tx_delay 2

[usb1_param] usbphy reg 32, set sh = 0x8, get sh = 0x8, 4bit

[usb1_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit

[usb1_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit

[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit

[usb1_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit

[usb1_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit

[usb1_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit

[usb1_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit

[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit

[usb2_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit

[usb2_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit

[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit

[usb2_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit

[usb2_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit

[usb2_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit

[usb2_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[cfyeh] set PPE = 0

[usb_param] setting for jupiter

#######[cfyeh-debug] USBPHY_Register_Setting(893) jupiter D

[usb_param] set port two for host!

#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 1

#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 1

#@# cfyeh-debug USBPHY_SetReg_Default_39(417) tx_delay 2

[usb1_param] usbphy reg 32, set sh = 0x8, get sh = 0x8, 4bit

[usb1_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit

[usb1_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit

[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit

[usb1_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit

[usb1_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit

[usb1_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit

[usb1_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit

[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit

[usb2_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit

[usb2_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit

[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit

[usb2_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit

[usb2_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit

[usb2_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit

[usb2_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

#######[cfyeh-debug] hub_events(3177) usb_plug_status 1

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

Initializing USB Mass Storage driver...

usb 1-1: new high speed USB device using ehci_hcd and address 2

hub 1-1:1.0: USB hub found

hub 1-1:1.0: 4 ports detected

hub : individual port power switching

hub : individual port over-current protection

#######[cfyeh-debug] hub_events(3193) usb_plug_status 0

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

#######[cfyeh-debug] dwc_otg_driver_init(900) for otg device

Setting registers , Enable OTG

dwc_otg: version 2.60a 22-NOV-2006

DWC_otg: Shared Tx FIFO mode

i2c /dev entries driver

[I2C0] i2c speed changed to 100 KHz

I2C0 Bus Status Check.... OK

=========================

= VER : 2.1b

=========================

DWC_otg: USB RESET

= PHY : 0

= MODE: MARS/JUPITER

= SPD : 100

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 32

= RX FIFO DEPTH : 32

= FIFO THRESHOLD: 4

= BUS JAM RECORVER 3: ON

= NON STOP WRITE : OFF

= GPIO RW SUPPORT : ON

= I2C DELAY : ON

=========================

[I2C1] i2c speed changed to 100 KHz

I2C1 Bus Status Check.... OK

=========================

= VER : 2.1b

=========================

= PHY : 1

= MODE: MARS/JUPITER

= SPD : 100

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 32

= RX FIFO DEPTH : 32

= FIFO THRESHOLD: 4

= BUS JAM RECORVER 3: ON

= NON STOP WRITE : OFF

= GPIO RW SUPPORT : ON

= I2C DELAY : ON

=========================

#######[cfyeh-debug] hub_events(3177) usb_plug_status 1

SCPU_CLK90K=0.000 sec.

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 444k freed


init started: BusyBox v1.1.3 (2011.05.13-18:03+0000) multi-call binary

Starting pid 302, console /dev/console: '/etc/init.d/rcS'
120+0 records in
120+0 records out
Welcome to Realtek Rescue Linux for PhotoViewer
mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such device
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory

>>>>>> loader start! (May 14 2011:02:04:46, version=00.01.01)

Please press Enter to activate this console. usb 1-1.4: new high speed USB device using ehci_hcd and address 3

Hotplug: device "loop0" is skipped.
Hotplug: device "loop1" is skipped.
Hotplug: device "loop2" is skipped.
Hotplug: device "loop3" is skipped.
Hotplug: device "loop4" is skipped.
Hotplug: device "loop5" is skipped.
Hotplug: device "loop6" is skipped.
Hotplug: device "loop7" is skipped.
Hotplug: device "mtdblock0" is skipped.
Hotplug: device "ram0" is skipped.
scsi0 : SCSI emulation for USB Mass Storage devices

#######[cfyeh-debug] usb_stor_scan_thread(923) usb_plug_status 2

#######[cfyeh-debug] hub_events(3193) usb_plug_status 1

#######[cfyeh-debug] usb_stor_scan_thread(981) usb_plug_status 2

Vendor: SMI Model: USB DISK Rev: 1100

Type: Direct-Access ANSI SCSI revision: 00

SCSI device sda: 31690752 512-byte hdwr sectors (16226 MB)

sda: Write Protect is off

sda: assuming drive cache: write through

disk->capacity:0x1e39000

SCSI device sda: 31690752 512-byte hdwr sectors (16226 MB)

sda: Write Protect is off

sda: assuming drive cache: write through

disk->capacity:0x1e39000

/dev/scsi/host0/bus0/target0/lun0: p1

data[0] 0x0 signature[0] 0xbabeface

data[1] 0x0 signature[1] 0xdeadbeef

Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0

Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0

rmdir: `/var/lock/hotplu#######[cfyeh-debug] usb_stor_scan_thread(984) usb_plug_status 1

g/mount_tmp/.sda#######[cfyeh-debug] usb_stor_scan_thread(1000) usb_plug_status 0

'rmdir: `/var/lock/hotplug/mount_tmp/.sda1': No such file or directory
: No such file or directory
Hotplug: "sda" has partitions.
mount: Mounting /dev/scsi/host0/bus0/target0/lun0/part1 on /var/lock/hotplug/mount_tmp/.sda1 failed: No such device
mount: Mounting /dev/scsi/host0/bus0/target0/lun0/part1 on /var/lock/hotplug/mount_tmp/.sda1 failed: Invalid argument
modprobe: module sd_mod not found.
modprobe: failed to load module sd_mod
#######[cfyeh-debug] device_name_translating(248) open /sys/block/sda1/part_num fail!
Hotplug: mount -t ufsd -o force,rw -o nls=utf8 -o umask=0 /dev/scsi/host0/bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1 ret: 255
Hotplug: mount -t ntfs -o ro -o nls=utf8 -o umask=0 /dev/scsi/host0/bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1 ret: 255
Hotplug: mount -t vfat -o ro,shortname=winnt -o utf8 -o umask=0 /dev/scsi/host0/bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1 ret: 0
Hotplug: Mount "sda1" successfully.
+++ ALLOC index: 3072 order: 8

1. start remap DVR zone 81c00000(803d6000) 256...

map_done is 256...

--- FREE index: 3072 order: 8

[MCP][RSA] strip rsa header failed - no rsa padding header detected

loader_a.c:verona_load_func:1290 Error! Image file, /mnt/usbmounts/sda1/install.img, cannot be opened or the hash value is not correct.
+++ ALLOC index: 3072 order: 8

1. start remap DVR zone 81c00000(803d6000) 256...

map_done is 0...

--- FREE index: 3072 order: 8

[MCP][RSA] strip rsa header failed - no rsa padding header detected

loader_a.c:verona_load_func:1290 Error! Image file, /mnt/usbmounts/sda1/install.img, cannot be opened or the hash value is not correct.
+++ ALLOC index: 3072 order: 8

1. start remap DVR zone 81c00000(803d6000) 256...

map_done is 0...

--- FREE index: 3072 order: 8

[MCP][RSA] strip rsa header failed - no rsa padding header detected

loader_a.c:verona_load_func:1290 Error! Image file, /mnt/usbmounts/sda1/install.img, cannot be opened or the hash value is not correct.
+++ ALLOC index: 3072 order: 8


Померла нанд флеш или ошибаюсь?
ASUS O!Play Mini+ @ Mini_Plus_mos_r7
Alominer
 
Posts: 25
Joined: 04 May 2013, 20:00

Re: Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Postby Virtual » 25 Feb 2018, 14:39

loader_a.c:verona_load_func:1290 Error! Image file, /mnt/usbmounts/sda1/install.img, cannot be opened or the hash value is not correct.

реске не нравится подпись прошивки... ищи другую.

PS плеер то черный... так что для прошивки через кн. нужна обяз подписанная.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Postby Alominer » 26 Feb 2018, 15:54

Virtual
Очень странно. Как мог файл прошивки побиться в архиве. Причём пробовал 2 разные флешки.... мистика прям.
Перекачал прошивку и всё пошло как по маслу инструкции. Спасибо за помощь, видимо покупка нового плеера откладывается.
ASUS O!Play Mini+ @ Mini_Plus_mos_r7
Alominer
 
Posts: 25
Joined: 04 May 2013, 20:00

Re: Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Postby Virtual » 26 Feb 2018, 20:37

Alominer wrote:Virtual
Очень странно. Как мог файл прошивки побиться в архиве.

это обычно привет от мелкософта... если архив zip, и распаковать сразу на флешку.
+скачка архивов из венды иногда кончается битыми файлами внутри..... паранойю включать не буду но все же факт.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Postby Sneg » 15 May 2020, 17:39

Здравствуйте. На днях купил сиё чудо на авито. Плейер устраивает всем, почти полностью перекрывает мои запросы. Пытаюсь настроить wifi, но ни как не получается. Oplay видит роутер (ASUS RT-14U), тот ему присвоил айпи. Вижу плейер в карте роутера, но интернета на плейере нет. Ни к одному сервису подключиться не могу, не говоря об обновлении по воздуху. Шнурком не цеплял, так обжимка и провод на работе, а я в отпуске. Ещё он папки расшаренные на компе не видит(ВИН-10, подключен к роутеру шнурком), а ноут с Вин-7 по wi-fi видит. Подскажите, может какие настройки в роутере надо сделать?
O!Play HDP_R3_FW_128_PAL
Sneg
 
Posts: 1
Joined: 12 Feb 2012, 15:43

Re: Asus O!Play Mini Plus (обзор, баги, общие вопросы и тп)

Postby Pokrass » 15 May 2020, 17:45

1. viewtopic.php?f=30&t=1036
2. Вопросы по официальным прошивкам и их глюкам решаются на официальных ресурсах
3. За все годы с данным плеером подобной проблемы не наблюдалось. Все что на нем может работать - работает (при условии актуальной прошивки и обновленных модулях). Так что скорее всего она со стороны роутера (например выдает адрес типа 169..... или не выдает днс) и прав доступа 10 винды(например, рабочя группа, фаервол и тп).
IconBIT HDS7L Fw: AMP_r12 GUI: VRT
iNeXT HD1 W Fw: X3D_Series_V4.0.2b160406
User avatar
Pokrass
 
Posts: 3154
Joined: 18 Mar 2012, 04:18
Location: Плюк. Планета № 215 в Тентуре галактики "Кин-дза-дза" в Спирали.

Previous

Return to ASUS

Who is online

Users browsing this forum: No registered users and 21 guests