Konoos GV3765 (RTD1073DD)
![Post Post](./styles/prosilver/imageset/icon_post_target.gif)
by RomZESS5
Здраствуйте.
И так имеется 3 штуки Konoos GV3765 на чипе 1073
Первый пациент: сбился буткод - в гипертерминале всегда при подключении выдавал приглашение s/d/g/c>. Я пробовал разные варианты HwSettings + всякие буткоды в итоге смог запустить с каким то вариантом HwSettings и Bootcode 26 for Asus O!Play HD2, после очень долгой прошивки он заработал но с дикими тормозами и включениями через раз.
Второй пациент: тоже сбился буткод - опять таки всегда в гипертерминале при подключении выдает приглашение s/d/g/c> Не стал я его мучать после неудачных опытов с первым.
Третий не пациент еще пока: новый полностью рабочий девайс.
Подскажите какой HwSettings мне использовать? И где взять оригинальный буткод noon.0202.0026?(скопировал циферки с гипертерминала с рабочего девайса, теже показывает в меню инфо о прошивке сам девайс)
Или подскажите как слить буткод с рабочего девайса(какой командой?)
Пробовал слить с рабочего через телнет командой dd if=/dev/mtdblock/0 of=/tmp/usbmounts/sda1/flash0.img(правдо сначало пришлось перемонтировать флешку на rw, а то не писалсо), в итоге вышел файло на 190 мегов, а что с ним делать теперь незнаю и вообще сомневаюсь что в нем гдето спрятался буткод.
И еще, что за S-Flash возле чипа на фотке IMG_0766, что будет если замкнуть и включить? И N-Flash есть такойже снизу у чипа, не ясно както зачем это.
И что выполняет команда "c" в приглашении s/d/g/c>, ни разу не пробовал.
Отнеситесь к вопросу с пониманием, я всетаки не супер спец и много чего еще не знаю.
И так имеется 3 штуки Konoos GV3765 на чипе 1073
Первый пациент: сбился буткод - в гипертерминале всегда при подключении выдавал приглашение s/d/g/c>. Я пробовал разные варианты HwSettings + всякие буткоды в итоге смог запустить с каким то вариантом HwSettings и Bootcode 26 for Asus O!Play HD2, после очень долгой прошивки он заработал но с дикими тормозами и включениями через раз.
Второй пациент: тоже сбился буткод - опять таки всегда в гипертерминале при подключении выдает приглашение s/d/g/c> Не стал я его мучать после неудачных опытов с первым.
Третий не пациент еще пока: новый полностью рабочий девайс.
Подскажите какой HwSettings мне использовать? И где взять оригинальный буткод noon.0202.0026?(скопировал циферки с гипертерминала с рабочего девайса, теже показывает в меню инфо о прошивке сам девайс)
Или подскажите как слить буткод с рабочего девайса(какой командой?)
Пробовал слить с рабочего через телнет командой dd if=/dev/mtdblock/0 of=/tmp/usbmounts/sda1/flash0.img(правдо сначало пришлось перемонтировать флешку на rw, а то не писалсо), в итоге вышел файло на 190 мегов, а что с ним делать теперь незнаю и вообще сомневаюсь что в нем гдето спрятался буткод.
- Тут лог с рабочего аппарата, весь процесс включения | +
- Code: Select all
?hello world!
52805 w28a0 iwatiA~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A[HDMI]: Set I2C Speed = 100 kHz
[HDMI]: Chk_HotPlug() TV is not connected.
[HDMI]: Read_EDID abort, HDMI cable plug off.
[HDMI]: TV is not connected.
PAL logo
REALTEK ROM Monitor, Revision noon.0202.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.
For a list of available commands, type 'help'.
Compilation time /version= Nov 9 2010 11:27:40 /noon.0202.0026
MAC address = 00.11.22.cf.ff.ff
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x78
Endianness = Little
Flash memory size = 256 MByte
SDRAM size = 128 MByte
First free SDRAM address = 0x800fab00
Press 'ESC' to Monitor mode
Linux Kernel:
FW Image from 0xa2020000, to 0x80100000, size=0x401085
Audio FW:
FW Image from 0xa2440000, to 0x81b00000, size=0x1c9690
Video FW:
FW Image from 0xa2620000, to 0x81d80000, size=0x2376f0
5280Go 5280Go go 0x80100000 mtdparts=rtk_nand:194816k,37760k(/),16384k(/usr/local/etc),13184k rootfstype=squashfs root=31:01
Reset Ethernet Mac.
Address = 0x80100000
Realtek LINUX (DC ALIAS) started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 2 UARTs.
System CPU uses external timer interrupt.
Bootloader version: noon.0202.0026. This version string is of new format.
[0m[31;5mError! Unknown SB2_CHIP_INFO. Linux is too old?[0m
Ethernet Mac address: 00.11.22.cf.ff.ff
Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (root@138_korsen) (gcc version 3.4.4 mipssde-6.03.01-20051114) #1 Mon Aug 2 13:32:07 CST 2010
audio addr: 1b00000
CPU revision is: 00019378
Determined physical RAM map:
memory: 00100000 @ 00000000 (usable)
memory: 0041f000 @ 00100000 (reserved)
memory: 015e1000 @ 0051f000 (usable)
memory: 00500000 @ 01b00000 (reserved)
memory: 06000000 @ 02000000 (usable)
show info: max_low_pfn:32768
show info: min_low_pfn:1311
ZONE: DMA, PFN: 0
ZONE: DVR, PFN: 8192
Built 1 zonelists
Kernel command line: mtdparts=rtk_nand:194816k,37760k(/),16384k(/usr/local/etc),13184k rootfstype=squashfs root=31:01 console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 256 (order: 8, 4096 bytes)
Estimate value: CPU frequency 405.03 MHz
Using 27.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 119552k/121732k available (3385k kernel code, 2112k reserved, 570k data, 144k init, 0k highmem)
Warning! Unknown board id.
==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
========== board id: 202 ==========
[INFO] neptune mode...
boot_param value: a0002800
mode: 1
size: 1337
color1: 0x808010
color2: 0x808059
color3: 0x8080a2
color4: 0x8708
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
se init module major number = 254
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
[user land] CmdBuf virt addr = 80658000/a0658000, phy addr=00658000
Hello, Realtek TLB Mapper
AllocBP size: 294912 order: 7
<<<DVR FREE AREA>>>
0: 0
1: 0
2: 0
3: 0
4: 0
5: 0
6: 0
7: 0
8: 0
9: 0
10: 0
11: 0
12: 6
Addr: 87000000, order: 12
Addr: 86000000, order: 12
Addr: 85000000, order: 12
Addr: 84000000, order: 12
Addr: 83000000, order: 12
Addr: 82000000, order: 12
squashfs: version 3.1 (2006/08/19) Phillip Lougher
devfs: 2004-01-31 Richard Gooch (r
[Audio Firmware Version] 333437
[Binary src compiled at] Aug 31 2010 17:11:17
gooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
YAFFS Driver Rev:292241 (2010-01-19)
YAFFS Driver is successfully installing.
Initializing Cryptographic API
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize
loop: loaded (max 8 devices)
this MARS eth RX_OFFSET = 0x0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
MAC address = 0x00.11.22.cf.ff.ff
eth0: RTL-8139C+ at 0xb8016000, 00:11:22:cf:ff:ff, IRQ 2
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
VenusSFC MTD init
cp_hotplug
serial flash inaccessible
physmap flash device: 10000000 at fd00000
Realtek NAND Flash Driver Rev:317223 (2010-06-01)
One HY27UF082G2B chip has 1 die(s) on board
nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0
[rtk_nand_scan_bbt] have created bbt B0, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
4 cmdlinepart partitions found on MTD device rtk_nand
RTK: using dynamic nand partition
Creating 4 MTD partitions on "rtk_nand":
0x00000000-0x0be40000 : "Partition_000"
0x0be40000-0x0e320000 : "/"
0x0e320000-0x0f320000 : "/usr/local/etc"
0x0f320000-0x10000000 : "Partition_003"
0x00000000-0x10000000 : "disc"
Realtek Nand Flash Driver is successfully installing.
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODE: MARS/JUPITER
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 8
= RX FIFO DEPTH : 8
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
FATAL : I2C 1 pins have been occupied by PCI
Trying to free free IRQ3
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
Realtek Venus Power Management, (c) 2006 Realtek Semiconductor Corp.
cp_open
alloc rings cp->rxdesc_buf =0xa19a3000 , cp->ring_dma=0x19a3000
init_hw
init_hw finished
IP-Config: Complete:
device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
host=192.168.0.9, domain=, nis-domain=(none),
bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing prom memory: 0kb freed
Reclaim bootloader memory from 80020000 to 80100000
Freeing unused kernel memory: 144k freed
RTK rtc cannot work.
Welcome to Realtek Linux
Please press Enter to activate this console. ------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
------flush priority: 10
flush_page_cache: do flush...
[mtdblock_release] Done
[mtdblock_release] Done
[mtdblock_release] Done
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
Starting INET services....
[31mLcd Display logo..
[m [m[32m
[sjg] debug --->> </mnt/kernel/Linux_QA0915_090921/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_vfd.c> Lcd_ShowBmp():1030
[m[31mbmp x=32,y=48,w=96,h=32
[m [m[31mLcd Init over!
[m [mbuff write test data=0123456789
------flush priority: 10
flush_page_cache: do flush...
libata version 1.12 loaded.
sata driver initial...2009/11/26 17:40 test ver.
ata_device_add(4892)probe begin
scsi0 : SATA_DRV
sata dma reset
Running dvdplayer with RootApp
set corepath: /tmp/hdd/volumes/HDD1/
RootApp AVHDD version...
enter 2nd case...
================================================
================================================
root execute DvdPlayer...
================================================
================================================
IN : /tmp/ramfs/smb
downloader 0 starts, 0x102ecc88
downloader 1 starts, 0x102f1e78
sata1: reset phy again!
sata phy reset
MusicTVAP, MusicTVAP.cpp:38
CMD: mkdir -p /tmp/netb/smb
In my system...
CMD: mkdir -p /tmp/smb
In my system...
CMD: ifconfig > /tmp/netb/samba_my_ip
In my system...
Warning!! the Mask is 255.0.0.0.
GrandMa Revision: 337552
(User ***128MB version...
Input)Pipe Created.
(Internal E Memory address 0x40000000
vent)Pipe Created.
pli initialization...
[32m
[sjg] debug --->> <LCD_L.cpp> VFD_Controller():1019
[m[31mmmap addr=2aaa8000,size =0000a000,read test data = 0123456789
[31mLcd Display logo..
[m [m[32m
[sjg] debug --->> </mnt/kernel/Linux_QA0915_090921/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_vfd.c> Lcd_ShowBmp():1030
[m[31mbmp x=32,y=48,w=96,h=32
[m [mError in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
[m [m[32m
[sjg] debug --->> <LCD_L.cpp> Lcd_Init():869
[m[31mVfdStatus.status=00000001
[m [m[32m
[sjg] debug --->> <LCD_L.cpp> Get_Lcd_Parm():828
[m[31mMcuChipID=0
[m [m[31mLcdChipID=0
[m [m[31mScreen_dir=3
[m [m[31mH_size=160
[m [m[31mV_size=128
[m [m[31mBytesPerpixel=2
[m [m[31mcolor_format=1
[m [m[32m
[sjg] debug --->> <LCD_L.cpp> Lcd_Init():883
[m[31m
lcd init over!!!!!!!!!!!!!!!
[m [m607 loadThemeSetting resource.cpp
No THEMESET_INI exists
-=- create FT engine for ./Resource/hebrew.ttf
Abstract::Init,Mode:0 ---------chenal0716----
--------Abstract::Init Process----
file system 3, sector 0
mount to /tmp/hdd/volumes/HDD1
file system 1, sector 262144
mount to na
file system 2, sector 1048576
mount to /tmp/hdd/root
я
Node 0, zone DMA 1 0 0 0 0 1 0 1 1 1 0 1 0
free pages: 2977
Node 0, zone DVR 0 0 0 1 1 0 1 0 1 1 0 0 5
free pages: 21336
cached size: 2796
try_to_free_pages: free 905
Node 0, zone DMA 97 66 53 28 14 1 0 1 1 1 0 1 0
free pages: 3865
Node 0, zone DVR 0 0 0 1 1 0 1 0 1 1 0 0 5
free pages: 21336
cached size: 2796
+++ ALLOC index: 20480 order: 12
1. start remap DVR zone 87000000(80600000) 4096...
map_done is 0...
+++ ALLOC index: 16384 order: 10
1. start remap DVR zone 86000000(805e0000) 1024...
map_done is 0...
+++ ALLOC index: 18432 order: 11
1. start remap DVR zone 86800000(805f0000) 2048...
map_done is 0...
+++ ALLOC index: 12288 order: 11
1. start remap DVR zone 85000000(805c0000) 2048...
map_done is 0...
+++ ALLOC index: 17408 order: 8
1. start remap DVR zone 86400000(805e8000) 256...
map_done is 0...
+++ ALLOC index: 17664 order: 7
1. start remap DVR zone 86500000(805ea000) 128...
map_done is 0...
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805eb000) 128...
map_done is 0...
--- FREE index: 20480 order: 12
--- FREE index: 16384 order: 10
--- FREE index: 18432 order: 11
--- FREE index: 12288 order: 11
--- FREE index: 17408 order: 8
--- FREE index: 17664 order: 7
--- FREE index: 17792 order: 7
+++ ALLOC index: 16384 order: 8
1. start remap DVR zone 86000000(805e0000) 256...
map_done is 0...
start[0-3] = {7001a500, 7001a504, 7001a508, 7001a50c}
end[0-3] = {7001a510, 7001a514, 7001a518, 7001a51c}
+++ ALLOC index: 16896 order: 9
1. start remap DVR zone 86200000(805e4000) 512...
map_done is 0...
Video DebugMem PVIDEO_RPC_SetDebugMemory Called!+++ ALLOC index: 16640 order: 7
hysical Address 1. start remap DVR zone 86100000(805e2000) 128...
= 0x90be00
map_done is 0...
+++ ALLOC index: 16768 order: 7
1. start remap DVR zone 86180000(805e3000) 128...
map_done is 0...
+++ ALLOC index: 17408 order: 8
1. start remap DVR zone 86400000(805e8000) 256...
map_done is 0...
[AUDIO WARNING]
no more memory , do Remote Malloc. Size 0x00186008
+++ ALLOC index: 17920 order: 9
1. start remap DVR zone 86600000(805ec000) 512...
map_done is 0...
-------------------
Audio Version = 333437
Common Version = 330700
Build Date = Aug 31 2010
Build Time = 17:11:17
Note =
-------------------
ClassifyBonding DD 0x00000002
sata1: reset phy again!
sata phy reset
[Video Firmware Version] 332222
[Video Binary Built on] Aug 25 2010 13:57:05
Node 0, zone DMA 62 55 41 25 15 4 0 1 1 1 0 1 0
free pages: 3848
Node 0, zone DVR 3 6 3 2 1 1 0 0 2 1 0 1 4
free pages: 19547
cached size: 2828
try_to_free_pages: free 0
Node 0, zone DMA 62 55 41 25 15 4 0 1 1 1 0 1 0
free pages: 3848
Node 0, zone DVR 3 6 3 2 1 1 0 0 2 1 0 1 4
free pages: 19547
cached size: 2828
+++ ALLOC index: 12288 order: 12
1. start remap DVR zone 85000000(805c0000) 4096...
map_done is 0...
+++ ALLOC index: 18432 order: 10
1. start remap DVR zone 86800000(805f0000) 1024...
map_done is 0...
+++ ALLOC index: 17664 order: 3
1. start remap DVR zone 86500000(805ea000) 8...
map_done is 0...
Node 0, zone DMA 65 55 41 25 15 4 0 1 1 1 0 1 0
free pages: 3851
Node 0, zone DVR 3 6 3 3 2 2 1 1 1 1 1 0 3
free pages: 14419
cached size: 2828
try_to_free_pages: free 0
Node 0, zone DMA 65 55 41 25 15 4 0 1 1 1 0 1 0
free pages: 3851
Node 0, zone DVR 3 6 3 3 2 2 1 1 1 1 1 0 3
free pages: 14419
cached size: 2828
+++ ALLOC index: 20480 order: 12
1. start remap DVR zone 87000000(80600000) 4096...
map_done is 0...
Node 0, zone DMA 67 55 41 25 15 4 0 1 1 1 0 1 0
free pages: 3853
Node 0, zone DVR 3 6 3 3 2 2 1 1 1 1 1 0 2
free pages: 10323
cached size: 2828
try_to_free_pages: free 11
Node 0, zone DMA 58 54 39 27 15 4 0 1 1 1 0 1 0
free pages: 3850
Node 0, zone DVR 0 0 3 3 2 2 1 1 1 1 1 0 2
free pages: 10308
cached size: 2829
+++ ALLOC index: 8192 order: 12
1. start remap DVR zone 84000000(805a0000) 4096...
map_done is 0...
VBM: configured to SD!
[BONDING] ac3_dts_ddp dec= 0x00000000
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key = 0x00000001 (1 : has, 0: no key)
[BONDING] MLP ret= 0x00000000, key= 0x00000000, HBR= 0x00000001, dac= 0x00000000
dac's key = 0x00000000 (1 : has, 0: no key)
[BONDING] MLP ret= 0xffffffff, key= 0x00000000, HBR= 0x00000001, dac= 0x00000001
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (1,0,0)
Do you have key?(0 = no!) 0
Bonding option process 0x00000009 to AUDIO_UNKNOWN_TYPE !!!
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key = 0x00000001 (1 : has, 0: no key)
[BONDING] DTSHD ret= 0x00010000, getkey= 0x00000000, HBR = 0x00000001, dac= 0x00000000dac's key = 0x00000001 (1 : has, 0: no key)
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process 0x0000001b to AUDIO_UNKNOWN_TYPE !!!
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process 0x0000001c to AUDIO_UNKNOWN_TYPE !!!
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process 0x0000001d to AUDIO_UNKNOWN_TYPE !!!
dac's key = 0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,0,1)
Do you have key?(0 = no!) 0
Bonding option process 0x00000023 to AUDIO_UNKNOWN_TYPE !!!
High = 0x00000000, Low = 0x03c1b5fe
The following Format is supported:
MPEG
AC3
LPCM
DTS
WMA
AAC
VORBIS
DV
DDP (AC3+, EAC3)
WMA Pro
MP4 LC-AAC
MP4 HE-AAC
RAW AAC
ADPCM
FLAC
A Law PCM
u Law PCM
[VIDEO Capability]HighWord 0xffffffff, LowWord 0xffffffff
[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Mars
[HDMI]: MARS HDMI is running...
[HDMI]: Disable HDCP
[HDMI]: Set I2C Speed = 50 kHz a[I2C0] i2c speed changed to 50 KHz
nd increase i2c +++ ALLOC index: 4096 order: 11
pull-low strengt1. start remap DVR zone 83000000(80580000) 2048...
h.
[HDMI]: Hotpmap_done is 0...
lug Change !!! -1 -> 0
~~SetVideoStandard 13 1
Activate
m_browserDevice: 3
WARNING[5]:TVE p-underflow @ line 0
WARNING[4]:TVE i-underflow @ line 49
WARNING[2]:TVE ISR Late i_vcnt =49
2996 SetCurrentBrowserTypeChoice GNewBrowserMenu.cpp 3
GNewBrowserMenu.+++ ALLOC index: 19456 order: 9
cpp:2722, IsBrow1. start remap DVR zone 86c00000(805f8000) 512...
serDirExist() ismap_done is 0...
false
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805eb000) 128...
map_done is 0...
--- FREE index: 19456 order: 9
--- FREE index: 17792 order: 7
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 8...
--- FREE index: 17672 order: 3
Error in thresho+++ ALLOC index: 17672 order: 3
ld value: 0...
1. start remap DVR zone 86508000(805ea100) 8...
WatchDog does nomap_done is 0...
t receive signal for 2 seconds, --- FREE index: 17672 order: 3
value: 0
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 19456 order: 9
1. start remap DVR zone 86c00000(805f8000) 512...
map_done is 0...
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805eb000) 128...
map_done is 0...
--- FREE index: 19456 order: 9
--- FREE index: 17792 order: 7
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 19456 order: 8
1. start remap DVR zone 86c00000(805f8000) 256...
map_done is 0...
+++ ALLOC index: 17728 order: 6
1. start remap DVR zone 86540000(805ea800) 64...
map_done is 64...
--- FREE index: 19456 order: 8
--- FREE index: 17728 order: 6
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 8...
--- FREE index: 17672 order: 3
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
[GBrowserAP.cpp:526]:GiveUpFocus()- %%%%%% - !!
IN : /tmp/net
Create /tmp/net Ok!!!
In my system...
GNewBrowserMenu.+++ ALLOC index: 19456 order: 9
cpp:2722, IsBrow1. start remap DVR zone 86c00000(805f8000) 512...
serDirExist() ismap_done is 0...
false
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805eb000) 128...
map_done is 82...
--- FREE index: 19456 order: 9
--- FREE index: 17792 order: 7
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 8...
--- FREE index: 17672 order: 3
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 19456 order: 9
1. start remap DVR zone 86c00000(805f8000) 512...
map_done is 0...
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805eb000) 128...
map_done is 0...
--- FREE index: 19456 order: 9
--- FREE index: 17792 order: 7
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 19456 order: 8
1. start remap DVR zone 86c00000(805f8000) 256...
map_done is 0...
+++ ALLOC index: 17728 order: 6
1. start remap DVR zone 86540000(805ea800) 64...
map_done is 64...
--- FREE index: 19456 order: 8
--- FREE index: 17728 order: 6
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 8...
--- FREE index: 17672 order: 3
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
[GBrowserAP.cpp:526]:GiveUpFocus()- %%%%%% - !!
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
m_hDisplaySurfac+++ ALLOC index: 19456 order: 9
e from OsdManage1. start remap DVR zone 86c00000(805f8000) 512...
rTopView::showOSmap_done is 0...
D function = 272519056
GNewBrow+++ ALLOC index: 17792 order: 7
serMenu.cpp:27221. start remap DVR zone 86580000(805eb000) 128...
, IsBrowserDirExmap_done is 0...
ist() is false
--- FREE index: 19456 order: 9
--- FREE index: 17792 order: 7
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
sata1: reset phy extra!
sata phy reset
+++ ALLOC index: 19456 order: 9
1. start remap DVR zone 86c00000(805f8000) 512...
map_done is 0...
+++ ALLOC index: 17792 order: 7
1. start remap DVR zone 86580000(805eb000) 128...
map_done is 0...
--- FREE index: 19456 order: 9
--- FREE index: 17792 order: 7
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
+++ ALLOC index: 19456 order: 8
1. start remap DVR zone 86c00000(805f8000) 256...
map_done is 0...
+++ ALLOC index: 17728 order: 6
1. start remap DVR zone 86540000(805ea800) 64...
map_done is 0...
--- FREE index: 19456 order: 8
--- FREE index: 17728 order: 6
+++ ALLOC index: 17672 order: 3
1. start remap DVR zone 86508000(805ea100) 8...
map_done is 0...
--- FREE index: 17672 order: 3
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
Init--AbstractAP.cpp--1766-------chenal 0927-----btsamba_info
In my system...
In my system...
[WT] Device number=0
In my system...
Algorithmics/MIPS FPU Emulator v1.5
In my system...
In my system...
In my system...
In my system...
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ehci_hcd ehci_hcd: EHCI Host Controller
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub : individual port power switching
hub : individual port over-current protection
[HDMI]: Seup HDMI HPD GPIO.
[HDMI]: Setup_HPD_GPIO, de-bounce = 10 ms Mars
[cfyeh] set PPE = 0
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection
usb 1-1: new high speed USB device using ehci_hcd and address 2
In my system...
This is the current time: PowerUP_Done!!!
Audio version number: 333437
Video version number: 332222
[32m
[sjg] debug --->> <main.cpp> main():810
[m[31minto main function ........
[m [mMSDL_ZHU:AbstractAP.cpp(msdl_thread_func)[7247]:-==-->
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub : ganged power switching
hub : global over-current protection
eeeeeeeeeeeeeeeeeeeeee, ProcessKey, GBrowserAP.cpp:1167
AP:GBrowserAP , cmd_buffer.type:29
[+++ ALLOC index: 19456 order: 8
32m
[sjg] debu1. start remap DVR zone 86c00000(805f8000) 256...
g --->> <main.cpmap_done is 0...
p> main():927
+++ ALLOC index: 17728 order: 6
[m[31m<[sjg] 1. start remap DVR zone 86540000(805ea800) 64...
AP:GBrowserAP , ProcessKey retval=0, cmd_buffer.type:29
.idApp=ffffffff, parm[0]=00000000>
[m [m[System2ApDaemon.cpp,threadSys2ApExe,156]msg type = 6 ,msg len = 5 ,msg = 31 20 55 50 00map_done is 59...
00 00 00
Hotplug got one USB Hotplug of "Add" from port "1".
AP:GBrowserAP , cmd_buffer.type:4
[32m
[sjg] debug --->> <main.cpp> main():927
[m[31m<[sjg] AP:GBrowserAP , ProcessKey retval=0, cmd_buffer.type:4
.idApp=ffffffff, parm[0]=00000015>
watchdog test pid 190, threshold: 50
sata1: reset phy extra!
sata phy reset
watchdog test pid 190, threshold: 50
--- FREE index: 19456 order: 8
--- FREE index: 17728 order: 6
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata1: reset phy extra!
sata phy reset
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata1: phy reset timeout!
sata1: no device found (phy stat 00000000)
sata1: ata_bus_probe failed
scsi1 : SATA_DRV
sata dma reset
sata2: reset phy again!
sata phy reset
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata2: reset phy again!
sata phy reset
watchdog test pid 190, threshold: 50
watchdog test pisata2: phy reset timeout!
d 190, thresholdsata2: no device found (phy stat 00000000)
: 50
sata2: ata_bus_probe failed
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
- Я тут приложил на всяк случай фоточки чипегов | +
- IMG_0775.JPG (628.86 KiB) Viewed 14671 times
- IMG_0767.JPG (520.66 KiB) Viewed 14671 times
- IMG_0766.JPG (771.33 KiB) Viewed 14671 times
И еще, что за S-Flash возле чипа на фотке IMG_0766, что будет если замкнуть и включить? И N-Flash есть такойже снизу у чипа, не ясно както зачем это.
И что выполняет команда "c" в приглашении s/d/g/c>, ни разу не пробовал.
Отнеситесь к вопросу с пониманием, я всетаки не супер спец и много чего еще не знаю.