Page 1 of 1

Konoos GV3765 (RTD1073DD)

PostPosted: 12 Apr 2012, 14:57
by RomZESS5
Здраствуйте.

И так имеется 3 штуки Konoos GV3765 на чипе 1073
Первый пациент: сбился буткод - в гипертерминале всегда при подключении выдавал приглашение s/d/g/c>. Я пробовал разные варианты HwSettings + всякие буткоды в итоге смог запустить с каким то вариантом HwSettings и Bootcode 26 for Asus O!Play HD2, после очень долгой прошивки он заработал но с дикими тормозами и включениями через раз.
Второй пациент: тоже сбился буткод - опять таки всегда в гипертерминале при подключении выдает приглашение s/d/g/c> Не стал я его мучать после неудачных опытов с первым.
Третий не пациент еще пока: новый полностью рабочий девайс.

Подскажите какой HwSettings мне использовать? И где взять оригинальный буткод noon.0202.0026?(скопировал циферки с гипертерминала с рабочего девайса, теже показывает в меню инфо о прошивке сам девайс)
Или подскажите как слить буткод с рабочего девайса(какой командой?)
Пробовал слить с рабочего через телнет командой dd if=/dev/mtdblock/0 of=/tmp/usbmounts/sda1/flash0.img(правдо сначало пришлось перемонтировать флешку на rw, а то не писалсо), в итоге вышел файло на 190 мегов, а что с ним делать теперь незнаю и вообще сомневаюсь что в нем гдето спрятался буткод.

Тут лог с рабочего аппарата, весь процесс включения | +
Code: Select all
 
?hello  world!
52805 w28a0 iwatiA~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A[HDMI]: Set I2C Speed = 100 kHz

[HDMI]: Chk_HotPlug() TV is not connected.

[HDMI]: Read_EDID abort, HDMI cable plug off.

[HDMI]: TV is not connected.

PAL logo


REALTEK ROM Monitor, Revision noon.0202.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      Nov  9 2010  11:27:40  /noon.0202.0026

MAC address =                   00.11.22.cf.ff.ff

Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision =         0x93 / 0x78

Endianness =                    Little
Flash memory size =             256 MByte

SDRAM size =                    128 MByte

First free SDRAM address =      0x800fab00


Press 'ESC' to Monitor mode

Linux Kernel:

   FW Image from 0xa2020000, to 0x80100000, size=0x401085

Audio FW:

   FW Image from 0xa2440000, to 0x81b00000, size=0x1c9690

Video FW:

   FW Image from 0xa2620000, to 0x81d80000, size=0x2376f0

5280Go 5280Go go 0x80100000 mtdparts=rtk_nand:194816k,37760k(/),16384k(/usr/local/etc),13184k rootfstype=squashfs root=31:01

Reset Ethernet Mac.




Address = 0x80100000


Realtek LINUX (DC ALIAS) started...
Venus setting:
   ROSs have 2621440 bytes RAM.
   System CPU has 2 UARTs.
   System CPU uses external timer interrupt.
   Bootloader version: noon.0202.0026. This version string is of new format.
Error! Unknown SB2_CHIP_INFO. Linux is too old?
   Ethernet Mac address: 00.11.22.cf.ff.ff
   Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (root@138_korsen) (gcc version 3.4.4 mipssde-6.03.01-20051114) #1 Mon Aug 2 13:32:07 CST 2010

audio addr: 1b00000

CPU revision is: 00019378

Determined physical RAM map:

 memory: 00100000 @ 00000000 (usable)

 memory: 0041f000 @ 00100000 (reserved)

 memory: 015e1000 @ 0051f000 (usable)

 memory: 00500000 @ 01b00000 (reserved)

 memory: 06000000 @ 02000000 (usable)

  show info: max_low_pfn:32768

  show info: min_low_pfn:1311

ZONE: DMA, PFN: 0

ZONE: DVR, PFN: 8192

Built 1 zonelists

Kernel command line: mtdparts=rtk_nand:194816k,37760k(/),16384k(/usr/local/etc),13184k rootfstype=squashfs root=31:01 console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Estimate value: CPU frequency 405.03 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 119552k/121732k available (3385k kernel code, 2112k reserved, 570k data, 144k init, 0k highmem)

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction...  available.

========== board id: 202 ==========

[INFO] neptune mode...

boot_param value: a0002800

mode: 1

size: 1337

color1: 0x808010

color2: 0x808059

color3: 0x8080a2

color4: 0x8708

NET: Registered protocol family 16

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

se init module major number = 254

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

[user land] CmdBuf virt addr = 80658000/a0658000, phy addr=00658000

   Hello, Realtek TLB Mapper

   AllocBP size: 294912 order: 7

   <<<DVR FREE AREA>>>

   0:   0

   1:   0

   2:   0

   3:   0

   4:   0

   5:   0

   6:   0

   7:   0

   8:   0

   9:   0

   10:   0

   11:   0

   12:   6

      Addr: 87000000, order: 12

      Addr: 86000000, order: 12

      Addr: 85000000, order: 12

      Addr: 84000000, order: 12

      Addr: 83000000, order: 12

      Addr: 82000000, order: 12

squashfs: version 3.1 (2006/08/19) Phillip Lougher

devfs: 2004-01-31 Richard Gooch (r

[Audio Firmware Version] 333437
[Binary src compiled at] Aug 31 2010 17:11:17

gooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.

YAFFS Driver Rev:292241 (2010-01-19)

YAFFS Driver is successfully installing.

Initializing Cryptographic API

Generic RTC Driver v1.07

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

ttyS1 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

this  MARS eth RX_OFFSET = 0x0

8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)

MAC address = 0x00.11.22.cf.ff.ff

eth0: RTL-8139C+ at 0xb8016000, 00:11:22:cf:ff:ff, IRQ 2

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

NET: Registered protocol family 24

VenusSFC MTD init

cp_hotplug

serial flash inaccessible

physmap flash device: 10000000 at fd00000

Realtek NAND Flash Driver Rev:317223 (2010-06-01)

One HY27UF082G2B chip has 1 die(s) on board

nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

Congratulation!! No BBs in this Nand.

4 cmdlinepart partitions found on MTD device rtk_nand

RTK: using dynamic nand partition

Creating 4 MTD partitions on "rtk_nand":

0x00000000-0x0be40000 : "Partition_000"

0x0be40000-0x0e320000 : "/"

0x0e320000-0x0f320000 : "/usr/local/etc"

0x0f320000-0x10000000 : "Partition_003"

0x00000000-0x10000000 : "disc"

Realtek Nand Flash Driver is successfully installing.

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

i2c /dev entries driver

[I2C0] i2c speed changed to 100 KHz

I2C0 Bus Status Check.... OK

=========================

= VER : 2.1b               

=========================

= PHY : 0               

= MODE: MARS/JUPITER               

= SPD : 100               

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 8     

= RX FIFO DEPTH : 8     

= FIFO THRESHOLD: 4     

= BUS JAM RECORVER 3: ON 

= NON STOP WRITE : ON 

= GPIO RW SUPPORT : ON

=========================

FATAL : I2C 1 pins have been occupied by PCI

Trying to free free IRQ3

NET: Registered protocol family 2

IP: routing cache hash table of 1024 buckets, 8Kbytes

TCP established hash table entries: 8192 (order: 4, 65536 bytes)

TCP bind hash table entries: 8192 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 8192 bind 8192)

NET: Registered protocol family 1

NET: Registered protocol family 17

Realtek Venus Power Management, (c) 2006 Realtek Semiconductor Corp.

cp_open

alloc rings cp->rxdesc_buf =0xa19a3000 , cp->ring_dma=0x19a3000

init_hw

init_hw finished

IP-Config: Complete:

      device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,

     host=192.168.0.9, domain=, nis-domain=(none),

     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 144k freed

RTK rtc cannot work.

Welcome to Realtek Linux

Please press Enter to activate this console. ------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

[mtdblock_release] Done

[mtdblock_release] Done

[mtdblock_release] Done

yaffs: dev is 32505858 name is "mtdblock2"

yaffs: Attempting MTD mount on 31.2, "mtdblock2"

yaffs: auto selecting yaffs2

Starting INET services....
Lcd Display logo..

 

[sjg] debug --->> </mnt/kernel/Linux_QA0915_090921/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_vfd.c> Lcd_ShowBmp():1030

 bmp x=32,y=48,w=96,h=32

 Lcd Init over!

 buff write test data=0123456789

------flush priority: 10

flush_page_cache: do flush...

libata version 1.12 loaded.

sata driver initial...2009/11/26 17:40 test ver.

ata_device_add(4892)probe begin

scsi0 : SATA_DRV

sata dma reset

Running dvdplayer with RootApp
set corepath: /tmp/hdd/volumes/HDD1/

RootApp AVHDD version...
enter 2nd case...
================================================
================================================
root execute DvdPlayer...
================================================
================================================
IN : /tmp/ramfs/smb
downloader 0 starts, 0x102ecc88
downloader 1 starts, 0x102f1e78
sata1: reset phy again!

sata phy reset

MusicTVAP, MusicTVAP.cpp:38
CMD: mkdir -p /tmp/netb/smb
In my system...
CMD: mkdir -p /tmp/smb
In my system...
CMD: ifconfig > /tmp/netb/samba_my_ip
In my system...
Warning!! the Mask is 255.0.0.0.
GrandMa Revision: 337552
(User ***128MB version...

Input)Pipe Created.
(Internal E   Memory address 0x40000000

vent)Pipe Created.
pli initialization...

[sjg] debug --->> <LCD_L.cpp> VFD_Controller():1019
 mmap addr=2aaa8000,size =0000a000,read test data = 0123456789
Lcd Display logo..

 

[sjg] debug --->> </mnt/kernel/Linux_QA0915_090921/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_vfd.c> Lcd_ShowBmp():1030

 bmp x=32,y=48,w=96,h=32

 Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
 
[sjg] debug --->> <LCD_L.cpp> Lcd_Init():869
 VfdStatus.status=00000001
 
[sjg] debug --->> <LCD_L.cpp> Get_Lcd_Parm():828
 McuChipID=0
 LcdChipID=0
 Screen_dir=3
 H_size=160
 V_size=128
 BytesPerpixel=2
 color_format=1
 
[sjg] debug --->> <LCD_L.cpp> Lcd_Init():883
 


lcd init over!!!!!!!!!!!!!!!

 607 loadThemeSetting resource.cpp
No THEMESET_INI exists
-=- create FT engine for ./Resource/hebrew.ttf
Abstract::Init,Mode:0 ---------chenal0716----
--------Abstract::Init Process----
file system 3, sector 0
mount to /tmp/hdd/volumes/HDD1
file system 1, sector 262144
mount to na
file system 2, sector 1048576
mount to /tmp/hdd/root
я
Node 0, zone      DMA      1      0      0      0      0      1      0      1      1      1      0      1      0

free pages:  2977

Node 0, zone      DVR      0      0      0      1      1      0      1      0      1      1      0      0      5

free pages: 21336

cached size:  2796

try_to_free_pages: free 905

Node 0, zone      DMA     97     66     53     28     14      1      0      1      1      1      0      1      0

free pages:  3865

Node 0, zone      DVR      0      0      0      1      1      0      1      0      1      1      0      0      5

free pages: 21336

cached size:  2796

+++ ALLOC index: 20480 order: 12

1. start remap DVR zone 87000000(80600000) 4096...

map_done is 0...

+++ ALLOC index: 16384 order: 10

1. start remap DVR zone 86000000(805e0000) 1024...

map_done is 0...

+++ ALLOC index: 18432 order: 11

1. start remap DVR zone 86800000(805f0000) 2048...

map_done is 0...

+++ ALLOC index: 12288 order: 11

1. start remap DVR zone 85000000(805c0000) 2048...

map_done is 0...

+++ ALLOC index: 17408 order: 8

1. start remap DVR zone 86400000(805e8000) 256...

map_done is 0...

+++ ALLOC index: 17664 order: 7

1. start remap DVR zone 86500000(805ea000) 128...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 20480 order: 12

--- FREE index: 16384 order: 10

--- FREE index: 18432 order: 11

--- FREE index: 12288 order: 11

--- FREE index: 17408 order: 8

--- FREE index: 17664 order: 7

--- FREE index: 17792 order: 7

+++ ALLOC index: 16384 order: 8

1. start remap DVR zone 86000000(805e0000) 256...

map_done is 0...

start[0-3] = {7001a500, 7001a504, 7001a508, 7001a50c}
end[0-3] = {7001a510, 7001a514, 7001a518, 7001a51c}
+++ ALLOC index: 16896 order: 9

1. start remap DVR zone 86200000(805e4000) 512...

map_done is 0...

Video DebugMem PVIDEO_RPC_SetDebugMemory Called!+++ ALLOC index: 16640 order: 7

hysical Address 1. start remap DVR zone 86100000(805e2000) 128...

= 0x90be00
map_done is 0...

+++ ALLOC index: 16768 order: 7

1. start remap DVR zone 86180000(805e3000) 128...

map_done is 0...

+++ ALLOC index: 17408 order: 8

1. start remap DVR zone 86400000(805e8000) 256...

map_done is 0...

[AUDIO WARNING]
 no more memory , do Remote Malloc. Size  0x00186008
+++ ALLOC index: 17920 order: 9

1. start remap DVR zone 86600000(805ec000) 512...

map_done is 0...

-------------------
Audio Version = 333437
Common Version = 330700
Build Date = Aug 31 2010
Build Time = 17:11:17
Note =
-------------------
ClassifyBonding  DD   0x00000002
sata1: reset phy again!

sata phy reset




[Video Firmware Version]   332222
[Video Binary  Built on]   Aug 25 2010 13:57:05
Node 0, zone      DMA     62     55     41     25     15      4      0      1      1      1      0      1      0

free pages:  3848

Node 0, zone      DVR      3      6      3      2      1      1      0      0      2      1      0      1      4

free pages: 19547

cached size:  2828

try_to_free_pages: free 0

Node 0, zone      DMA     62     55     41     25     15      4      0      1      1      1      0      1      0

free pages:  3848

Node 0, zone      DVR      3      6      3      2      1      1      0      0      2      1      0      1      4

free pages: 19547

cached size:  2828

+++ ALLOC index: 12288 order: 12

1. start remap DVR zone 85000000(805c0000) 4096...

map_done is 0...

+++ ALLOC index: 18432 order: 10

1. start remap DVR zone 86800000(805f0000) 1024...

map_done is 0...

+++ ALLOC index: 17664 order: 3

1. start remap DVR zone 86500000(805ea000) 8...

map_done is 0...

Node 0, zone      DMA     65     55     41     25     15      4      0      1      1      1      0      1      0

free pages:  3851

Node 0, zone      DVR      3      6      3      3      2      2      1      1      1      1      1      0      3

free pages: 14419

cached size:  2828

try_to_free_pages: free 0

Node 0, zone      DMA     65     55     41     25     15      4      0      1      1      1      0      1      0

free pages:  3851

Node 0, zone      DVR      3      6      3      3      2      2      1      1      1      1      1      0      3

free pages: 14419

cached size:  2828

+++ ALLOC index: 20480 order: 12

1. start remap DVR zone 87000000(80600000) 4096...

map_done is 0...

Node 0, zone      DMA     67     55     41     25     15      4      0      1      1      1      0      1      0

free pages:  3853

Node 0, zone      DVR      3      6      3      3      2      2      1      1      1      1      1      0      2

free pages: 10323

cached size:  2828

try_to_free_pages: free 11

Node 0, zone      DMA     58     54     39     27     15      4      0      1      1      1      0      1      0

free pages:  3850

Node 0, zone      DVR      0      0      3      3      2      2      1      1      1      1      1      0      2

free pages: 10308

cached size:  2829

+++ ALLOC index: 8192 order: 12

1. start remap DVR zone 84000000(805a0000) 4096...

map_done is 0...

VBM: configured to SD!
[BONDING] ac3_dts_ddp dec= 0x00000000
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key =  0x00000001 (1 : has, 0: no key)
[BONDING] MLP ret= 0x00000000, key= 0x00000000, HBR= 0x00000001, dac= 0x00000000
dac's key =  0x00000000 (1 : has, 0: no key)
[BONDING] MLP ret= 0xffffffff, key= 0x00000000, HBR= 0x00000001, dac= 0x00000001
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (1,0,0)
Do you have key?(0 = no!) 0
Bonding option process  0x00000009 to AUDIO_UNKNOWN_TYPE !!!
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key =  0x00000001 (1 : has, 0: no key)
[BONDING] DTSHD ret= 0x00010000, getkey= 0x00000000, HBR =  0x00000001, dac= 0x00000000dac's key =  0x00000001 (1 : has, 0: no key)
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001b to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001c to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001d to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,0,1)
Do you have key?(0 = no!) 0
Bonding option process  0x00000023 to AUDIO_UNKNOWN_TYPE !!!
High =  0x00000000, Low =  0x03c1b5fe
The following Format is supported:
MPEG
AC3
LPCM
DTS
WMA
AAC
VORBIS
DV
DDP (AC3+, EAC3)
WMA Pro
MP4 LC-AAC
MP4 HE-AAC
RAW AAC
ADPCM
FLAC
A Law PCM
u Law PCM
[VIDEO Capability]HighWord  0xffffffff, LowWord  0xffffffff
[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Mars
[HDMI]: MARS HDMI is running...
[HDMI]: Disable HDCP
[HDMI]: Set I2C Speed = 50 kHz a[I2C0] i2c speed changed to 50 KHz

nd increase i2c +++ ALLOC index: 4096 order: 11

pull-low strengt1. start remap DVR zone 83000000(80580000) 2048...

h.
[HDMI]: Hotpmap_done is 0...

lug Change !!! -1 -> 0
~~SetVideoStandard 13 1
Activate

m_browserDevice: 3

WARNING[5]:TVE p-underflow @ line 0
WARNING[4]:TVE i-underflow @ line 49
WARNING[2]:TVE ISR Late i_vcnt =49
2996 SetCurrentBrowserTypeChoice GNewBrowserMenu.cpp 3
GNewBrowserMenu.+++ ALLOC index: 19456 order: 9

cpp:2722, IsBrow1. start remap DVR zone 86c00000(805f8000) 512...

serDirExist() ismap_done is 0...

 false
+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

Error in thresho+++ ALLOC index: 17672 order: 3

ld value: 0...
1. start remap DVR zone 86508000(805ea100) 8...

WatchDog does nomap_done is 0...

t receive signal for 2 seconds, --- FREE index: 17672 order: 3

value: 0
+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 9

1. start remap DVR zone 86c00000(805f8000) 512...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 8

1. start remap DVR zone 86c00000(805f8000) 256...

map_done is 0...

+++ ALLOC index: 17728 order: 6

1. start remap DVR zone 86540000(805ea800) 64...

map_done is 64...

--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
[GBrowserAP.cpp:526]:GiveUpFocus()- %%%%%% - !!
IN : /tmp/net
Create /tmp/net Ok!!!
In my system...
GNewBrowserMenu.+++ ALLOC index: 19456 order: 9

cpp:2722, IsBrow1. start remap DVR zone 86c00000(805f8000) 512...

serDirExist() ismap_done is 0...

 false
+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 82...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 9

1. start remap DVR zone 86c00000(805f8000) 512...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 8

1. start remap DVR zone 86c00000(805f8000) 256...

map_done is 0...

+++ ALLOC index: 17728 order: 6

1. start remap DVR zone 86540000(805ea800) 64...

map_done is 64...

--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
[GBrowserAP.cpp:526]:GiveUpFocus()- %%%%%% - !!
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
m_hDisplaySurfac+++ ALLOC index: 19456 order: 9

e from OsdManage1. start remap DVR zone 86c00000(805f8000) 512...

rTopView::showOSmap_done is 0...

D function = 272519056
GNewBrow+++ ALLOC index: 17792 order: 7

serMenu.cpp:27221. start remap DVR zone 86580000(805eb000) 128...

, IsBrowserDirExmap_done is 0...

ist() is false
--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

sata1: reset phy extra!

sata phy reset

+++ ALLOC index: 19456 order: 9

1. start remap DVR zone 86c00000(805f8000) 512...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 8

1. start remap DVR zone 86c00000(805f8000) 256...

map_done is 0...

+++ ALLOC index: 17728 order: 6

1. start remap DVR zone 86540000(805ea800) 64...

map_done is 0...

--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272519848
Init--AbstractAP.cpp--1766-------chenal 0927-----btsamba_info
In my system...
In my system...
[WT] Device number=0
In my system...
Algorithmics/MIPS FPU Emulator v1.5

In my system...
In my system...
In my system...
In my system...
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[HDMI]: Seup HDMI HPD GPIO.
[HDMI]: Setup_HPD_GPIO, de-bounce = 10 ms Mars
[cfyeh] set PPE = 0

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

usb 1-1: new high speed USB device using ehci_hcd and address 2

In my system...
This is the current time: PowerUP_Done!!!

Audio version number: 333437


Video version number: 332222



[sjg] debug --->> <main.cpp> main():810
 into main function ........
 MSDL_ZHU:AbstractAP.cpp(msdl_thread_func)[7247]:-==-->
hub 1-1:1.0: USB hub found

hub 1-1:1.0: 4 ports detected

hub : ganged power switching

hub : global over-current protection

eeeeeeeeeeeeeeeeeeeeee, ProcessKey, GBrowserAP.cpp:1167
AP:GBrowserAP , cmd_buffer.type:29
[+++ ALLOC index: 19456 order: 8

32m
[sjg] debu1. start remap DVR zone 86c00000(805f8000) 256...

g --->> <main.cpmap_done is 0...

p> main():927
+++ ALLOC index: 17728 order: 6

 <[sjg] 1. start remap DVR zone 86540000(805ea800) 64...

AP:GBrowserAP , ProcessKey retval=0,  cmd_buffer.type:29
 .idApp=ffffffff, parm[0]=00000000>
 [System2ApDaemon.cpp,threadSys2ApExe,156]msg type = 6 ,msg len = 5 ,msg = 31 20 55 50 00map_done is 59...

 00 00 00
Hotplug got one USB Hotplug of "Add" from port "1".
AP:GBrowserAP , cmd_buffer.type:4

[sjg] debug --->> <main.cpp> main():927
 <[sjg] AP:GBrowserAP , ProcessKey retval=0,  cmd_buffer.type:4
 .idApp=ffffffff, parm[0]=00000015>
watchdog test pid 190, threshold: 50
sata1: reset phy extra!

sata phy reset

watchdog test pid 190, threshold: 50
--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata1: reset phy extra!

sata phy reset

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata1: phy reset timeout!

sata1: no device found (phy stat 00000000)

sata1: ata_bus_probe failed

scsi1 : SATA_DRV

sata dma reset

sata2: reset phy again!

sata phy reset

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata2: reset phy again!

sata phy reset

watchdog test pid 190, threshold: 50
watchdog test pisata2: phy reset timeout!

d 190, thresholdsata2: no device found (phy stat 00000000)

: 50
sata2: ata_bus_probe failed

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50

Я тут приложил на всяк случай фоточки чипегов | +
IMG_0775.JPG
IMG_0775.JPG (628.86 KiB) Viewed 14079 times

IMG_0767.JPG
IMG_0767.JPG (520.66 KiB) Viewed 14079 times

IMG_0766.JPG
IMG_0766.JPG (771.33 KiB) Viewed 14079 times

И еще, что за S-Flash возле чипа на фотке IMG_0766, что будет если замкнуть и включить? И N-Flash есть такойже снизу у чипа, не ясно както зачем это.
И что выполняет команда "c" в приглашении s/d/g/c>, ни разу не пробовал.
Отнеситесь к вопросу с пониманием, я всетаки не супер спец и много чего еще не знаю.

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 12 Apr 2012, 15:59
by Virtual
viewtopic.php?f=21&t=1463
там HwSettings для прошивки и те бутблоки реску что есть в наличии.

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 12 Apr 2012, 16:15
by RomZESS5
Virtual wrote:http://www.moservices.org/forum/viewtopic.php?f=21&t=1463
там HwSettings для прошивки и те бутблоки реску что есть в наличии.

Я с той темки все и брал, но как писал выше ничего хорошего из этого не вышло, а что способов вытащить с исправного нет?

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 12 Apr 2012, 20:09
by Virtual
интересует первый зверь., что значит с дикими тормозами и включением через раз? (желательно в логах с консоли)
прошивка родная или amp?

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 16 Apr 2012, 10:21
by RomZESS5
Включается через раз - при включении выбивает автоматом на приглашение s/d/g/c> или обыкновенно грузится и включается
Тормозит - долгая реакция на нажатия кнопок в меню
Прошивка: родная
лог с консоли первого апарата | +
Code: Select all
?hello  world!
5280 wai5t280 waiA[HDMI]: Set I2C Speed = 100 kHz

[HDMI]: Chk_HotPlug() TV is connected.

[HDMI]: Tx Reads EDID from Rx. block=0

[HDMI]: EDID chksum valid!!! chksum=7936 chksum divide 256=0

DVI DEVICE

Logo Change to #0

Change to NTSC system

Logo Change to #1


REALTEK ROM Monitor, Revision 0001.0203.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      Aug 26 2010  17:25:18  /0001.0203.0026

MAC address =                   00.11.22.c4.18.31

Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision =         0x93 / 0x78

Endianness =                    Little
Flash memory size =             256 MByte

SDRAM size =                    128 MByte

First free SDRAM address =      0x800fcc00


USB slave cable detected

Press 'ESC' to Monitor mode

Linux Kernel:

   FW Image from 0xa2020000, to 0x80100000, size=0x401085

Audio FW:

   FW Image from 0xa2440000, to 0x81b00000, size=0x1c9690

Video FW:

   FW Image from 0xa2620000, to 0x81d80000, size=0x2376f0

5280Go 5280Go go 0x80100000 mtdparts=rtk_nand:194816k,37760k(/),16384k(/usr/local/etc),13184k rootfstype=squashfs root=31:01

Reset Ethernet Mac.




Address = 0x80100000


Realtek LINUX (DC ALIAS) started...
Venus setting:
   ROSs have 2621440 bytes RAM.
   System CPU has 2 UARTs.
   System CPU uses external timer interrupt.
   Bootloader version: 0001.0203.0026. This version string is of new format.
Error! Unknown SB2_CHIP_INFO. Linux is too old?
   Ethernet Mac address: 00.11.22.C4.18.31
   Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (root@138_korsen) (gcc version 3.4.4 mipssde-6.03.01-20051114) #1 Mon Aug 2 13:32:07 CST 2010

audio addr: 1b00000

CPU revision is: 00019378

Determined physical RAM map:

 memory: 00100000 @ 00000000 (usable)

 memory: 0041f000 @ 00100000 (reserved)

 memory: 015e1000 @ 0051f000 (usable)

 memory: 00500000 @ 01b00000 (reserved)

 memory: 06000000 @ 02000000 (usable)

  show info: max_low_pfn:32768

  show info: min_low_pfn:1311

ZONE: DMA, PFN: 0

ZONE: DVR, PFN: 8192

Built 1 zonelists

Kernel command line: mtdparts=rtk_nand:194816k,37760k(/),16384k(/usr/local/etc),13184k rootfstype=squashfs root=31:01 console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Estimate value: CPU frequency 405.02 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 119552k/121732k available (3385k kernel code, 2112k reserved, 570k data, 144k init, 0k highmem)

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction...  available.

========== board id: 10203 ==========

[INFO] neptune mode...

boot_param value: a0002800

mode: 1

size: 991

color1: 0x808010

color2: 0x8080a2

color3: 0x8080eb

color4: 0x808059

NET: Registered protocol family 16

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

se init module major number = 254

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

[user land] CmdBuf virt addr = 80658000/a0658000, phy addr=00658000

   Hello, Realtek TLB Mapper

   AllocBP size: 294912 order: 7

   <<<DVR FREE AREA>>>

   0:   0

   1:   0

   2:   0

   3:   0

   4:   0

   5:   0

   6:   0

   7:   0

   8:   0

   9:   0

   10:   0

   11:   0

   12:   6

      Addr: 87000000, order: 12

      Addr: 86000000, order: 12

      Addr: 85000000, order: 12

      Addr: 84000000, order: 12

      Addr: 83000000, order: 12

      Addr: 82000000, order: 12

squashfs: version 3.1 (2006/08/19) Phillip Lougher

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.

[Audio Firmware Version] 333437
[Binary src compiled at] Aug 31 2010 17:11:17

au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.

YAFFS Driver Rev:292241 (2010-01-19)

YAFFS Driver is successfully installing.

Initializing Cryptographic API

Generic RTC Driver v1.07

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

ttyS1 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

this  MARS eth RX_OFFSET = 0x0

8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)

MAC address = 0x00.11.22.C4.18.31

eth0: RTL-8139C+ at 0xb8016000, 00:11:22:c4:18:31, IRQ 2

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

NET: Registered protocol family 24

VenusSFC MTD init

serial flash inaccessible

cp_hotplug

physmap flash device: 10000000 at fd00000

Realtek NAND Flash Driver Rev:317223 (2010-06-01)

One HY27UF082G2B chip has 1 die(s) on board

nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

Congratulation!! No BBs in this Nand.

4 cmdlinepart partitions found on MTD device rtk_nand

RTK: using dynamic nand partition

Creating 4 MTD partitions on "rtk_nand":

0x00000000-0x0be40000 : "Partition_000"

0x0be40000-0x0e320000 : "/"

0x0e320000-0x0f320000 : "/usr/local/etc"

0x0f320000-0x10000000 : "Partition_003"

0x00000000-0x10000000 : "disc"

Realtek Nand Flash Driver is successfully installing.

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

i2c /dev entries driver

[I2C0] i2c speed changed to 100 KHz

I2C0 Bus Status Check.... OK

=========================

= VER : 2.1b               

=========================

= PHY : 0               

= MODE: MARS/JUPITER               

= SPD : 100               

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 8     

= RX FIFO DEPTH : 8     

= FIFO THRESHOLD: 4     

= BUS JAM RECORVER 3: ON 

= NON STOP WRITE : ON 

= GPIO RW SUPPORT : ON

=========================

FATAL : I2C 1 pins have been occupied by PCI

Trying to free free IRQ3

NET: Registered protocol family 2

IP: routing cache hash table of 1024 buckets, 8Kbytes

TCP established hash table entries: 8192 (order: 4, 65536 bytes)

TCP bind hash table entries: 8192 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 8192 bind 8192)

NET: Registered protocol family 1

NET: Registered protocol family 17

Realtek Venus Power Management, (c) 2006 Realtek Semiconductor Corp.

cp_open

alloc rings cp->rxdesc_buf =0xa19a3000 , cp->ring_dma=0x19a3000

init_hw

init_hw finished

IP-Config: Complete:

      device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,

     host=192.168.0.9, domain=, nis-domain=(none),

     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 144k freed

RTK rtc cannot work.

Welcome to Realtek Linux

Please press Enter to activate this console. ------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

------flush priority: 10

flush_page_cache: do flush...

[mtdblock_release] Done

[mtdblock_release] Done

[mtdblock_release] Done

yaffs: dev is 32505858 name is "mtdblock2"

yaffs: Attempting MTD mount on 31.2, "mtdblock2"

yaffs: auto selecting yaffs2

Starting INET services....
Lcd Display logo..

 

[sjg] debug --->> </mnt/kernel/Linux_QA0915_090921/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_vfd.c> Lcd_ShowBmp():1030

 bmp x=32,y=48,w=96,h=32

 Lcd Init over!

 buff write test data=0123456789

------flush priority: 10

flush_page_cache: do flush...

libata version 1.12 loaded.

sata driver initial...2009/11/26 17:40 test ver.

ata_device_add(4892)probe begin

scsi0 : SATA_DRV

sata dma reset

Running dvdplayer with RootApp
set corepath: /tmp/hdd/volumes/HDD1/

RootApp AVHDD version...
enter 2nd case...
================================================
================================================
root execute DvdPlayer...
================================================
================================================
IN : /tmp/ramfs/smb
downloader 0 starts, 0x102ecc88
downloader 1 starts, 0x102f1e78
sata1: reset phy again!

sata phy reset

MusicTVAP, MusicTVAP.cpp:38
CMD: mkdir -p /tmp/netb/smb
In my system...
CMD: mkdir -p /tmp/smb
In my system...
CMD: ifconfig > /tmp/netb/samba_my_ip
In my system...
Warning!! the Mask is 255.0.0.0.
GrandMa Revision: 337552
(User ***128MB version...

Input)Pipe Created.
(Internal E   Memory address 0x40000000

vent)Pipe Created.
pli initialization...

[sjg] debug --->> <LCD_L.cpp> VFD_Controller():1019
 mmap addr=2aaa8000,size =0000a000,read test data = 0123456789
Lcd Display logo..

 

[sjg] debug --->> </mnt/kernel/Linux_QA0915_090921/linux-2.6.12/arch/mips/realtek-boards/drivers/venus_vfd.c> Lcd_ShowBmp():1030

 bmp x=32,y=48,w=96,h=32

 Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
 
[sjg] debug --->> <LCD_L.cpp> Lcd_Init():869
 VfdStatus.status=00000001
 
[sjg] debug --->> <LCD_L.cpp> Get_Lcd_Parm():828
 McuChipID=0
 LcdChipID=0
 Screen_dir=3
 H_size=160
 V_size=128
 BytesPerpixel=2
 color_format=1
 
[sjg] debug --->> <LCD_L.cpp> Lcd_Init():883
 


lcd init over!!!!!!!!!!!!!!!

 607 loadThemeSetting resource.cpp
No THEMESET_INI exists
-=- create FT engine for ./Resource/hebrew.ttf
Abstract::Init,Mode:0 ---------chenal0716----
--------Abstract::Init Process----
file system 3, sector 0
mount to /tmp/hdd/volumes/HDD1
file system 1, sector 262144
mount to na
file system 2, sector 1048576
mount to /tmp/hdd/root
я
Node 0, zone      DMA      1      0      0      0      0      1      0      1      1      1      0      1      0

free pages:  2977

Node 0, zone      DVR      0      0      0      1      1      0      1      0      1      1      0      0      5

free pages: 21336

cached size:  2796

try_to_free_pages: free 905

Node 0, zone      DMA     92     74     55     26     14      1      0      1      1      1      0      1      0

free pages:  3868

Node 0, zone      DVR      0      0      0      1      1      0      1      0      1      1      0      0      5

free pages: 21336

cached size:  2796

+++ ALLOC index: 20480 order: 12

1. start remap DVR zone 87000000(80600000) 4096...

map_done is 0...

+++ ALLOC index: 16384 order: 10

1. start remap DVR zone 86000000(805e0000) 1024...

map_done is 0...

+++ ALLOC index: 18432 order: 11

1. start remap DVR zone 86800000(805f0000) 2048...

map_done is 0...

+++ ALLOC index: 12288 order: 11

1. start remap DVR zone 85000000(805c0000) 2048...

map_done is 0...

+++ ALLOC index: 17408 order: 8

1. start remap DVR zone 86400000(805e8000) 256...

map_done is 0...

+++ ALLOC index: 17664 order: 7

1. start remap DVR zone 86500000(805ea000) 128...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 20480 order: 12

--- FREE index: 16384 order: 10

--- FREE index: 18432 order: 11

--- FREE index: 12288 order: 11

--- FREE index: 17408 order: 8

--- FREE index: 17664 order: 7

--- FREE index: 17792 order: 7

+++ ALLOC index: 16384 order: 8

1. start remap DVR zone 86000000(805e0000) 256...

map_done is 0...

start[0-3] = {7001a500, 7001a504, 7001a508, 7001a50c}
end[0-3] = {7001a510, 7001a514, 7001a518, 7001a51c}
+++ ALLOC index: 16896 order: 9

1. start remap DVR zone 86200000(805e4000) 512...

map_done is 0...

Video DebugMem PVIDEO_RPC_SetDebugMemory Called!+++ ALLOC index: 16640 order: 7

hysical Address 1. start remap DVR zone 86100000(805e2000) 128...

= 0xe6e00
map_done is 0...

+++ ALLOC index: 16768 order: 7

1. start remap DVR zone 86180000(805e3000) 128...

map_done is 0...

+++ ALLOC index: 17408 order: 8

1. start remap DVR zone 86400000(805e8000) 256...

map_done is 0...

[AUDIO WARNING]
 no more memory , do Remote Malloc. Size  0x00186008
+++ ALLOC index: 17920 order: 9

1. start remap DVR zone 86600000(805ec000) 512...

map_done is 0...

-------------------
Audio Version = 333437
Common Version = 330700
Build Date = Aug 31 2010
Build Time = 17:11:17
Note =
-------------------
ClassifyBonding  DD   0x00000002



[Video Firmware Version]   332222
[Video Binary  Built on]   Aug 25 2010 13:57:05
Node 0, zone      DMA     63     57     42     24     13      5      0      1      1      1      0      1      0

free pages:  3849

Node 0, zone      DVR      3      6      3      2      1      1      0      0      2      1      0      1      4

free pages: 19547

cached size:  2828

try_to_free_pages: free 0

Node 0, zone      DMA     63     57     42     24     13      5      0      1      1      1      0      1      0

free pages:  3849

Node 0, zone      DVR      3      6      3      2      1      1      0      0      2      1      0      1      4

free pages: 19547

cached size:  2828

+++ ALLOC index: 12288 order: 12

1. start remap DVR zone 85000000(805c0000) 4096...

sata1: reset phy again!

sata phy reset

map_done is 0...

+++ ALLOC index: 18432 order: 10

1. start remap DVR zone 86800000(805f0000) 1024...

map_done is 0...

+++ ALLOC index: 17664 order: 3

1. start remap DVR zone 86500000(805ea000) 8...

map_done is 0...

Node 0, zone      DMA     69     57     42     24     13      5      0      1      1      1      0      1      0

free pages:  3855

Node 0, zone      DVR      3      6      3      3      2      2      1      1      1      1      1      0      3

free pages: 14419

cached size:  2828

try_to_free_pages: free 0

Node 0, zone      DMA     69     57     42     24     13      5      0      1      1      1      0      1      0

free pages:  3855

Node 0, zone      DVR      3      6      3      3      2      2      1      1      1      1      1      0      3

free pages: 14419

cached size:  2828

+++ ALLOC index: 20480 order: 12

1. start remap DVR zone 87000000(80600000) 4096...

map_done is 0...

Node 0, zone      DMA     66     57     42     24     13      5      0      1      1      1      0      1      0

free pages:  3852

Node 0, zone      DVR      3      6      3      3      2      2      1      1      1      1      1      0      2

free pages: 10323

cached size:  2828

try_to_free_pages: free 11

Node 0, zone      DMA     62     57     41     23     14      5      0      1      1      1      0      1      0

free pages:  3852

Node 0, zone      DVR      0      0      3      3      2      2      1      1      1      1      1      0      2

free pages: 10308

cached size:  2829

+++ ALLOC index: 8192 order: 12

1. start remap DVR zone 84000000(805a0000) 4096...

map_done is 0...

VBM: configured to SD!
[BONDING] ac3_dts_ddp dec= 0x00000000
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key =  0x00000001 (1 : has, 0: no key)
[BONDING] MLP ret= 0x00000000, key= 0x00000000, HBR= 0x00000001, dac= 0x00000000
dac's key =  0x00000000 (1 : has, 0: no key)
[BONDING] MLP ret= 0xffffffff, key= 0x00000000, HBR= 0x00000001, dac= 0x00000001
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (1,0,0)
Do you have key?(0 = no!) 0
Bonding option process  0x00000009 to AUDIO_UNKNOWN_TYPE !!!
[BONDING] ac3_dts_ddp dec= 0x00000000
dac's key =  0x00000001 (1 : has, 0: no key)
[BONDING] DTSHD ret= 0x00010000, getkey= 0x00000000, HBR =  0x00000001, dac= 0x00000000dac's key =  0x00000001 (1 : has, 0: no key)
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001b to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001c to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,1,0)
Do you have key?(0 = no!) 0
Bonding option process  0x0000001d to AUDIO_UNKNOWN_TYPE !!!
dac's key =  0x00000000 (1 : has, 0: no key)
board = 1 !, if -1, this board has illegal ID
file is (AC3,DTS,WMA) (0,0,1)
Do you have key?(0 = no!) 0
Bonding option process  0x00000023 to AUDIO_UNKNOWN_TYPE !!!
High =  0x00000000, Low =  0x03c1b5fe
The following Format is supported:
MPEG
AC3
LPCM
DTS
WMA
AAC
VORBIS
DV
DDP (AC3+, EAC3)
WMA Pro
MP4 LC-AAC
MP4 HE-AAC
RAW AAC
ADPCM
FLAC
A Law PCM
u Law PCM
[VIDEO Capability]HighWord  0xffffffff, LowWord  0xffffffff
[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Mars
[HDMI]: MARS HDMI is running...
[HDMI]: Disable HDCP
[HDMI]: S[I2C0] i2c speed changed to 50 KHz

et I2C Speed = 50 kHz and increa+++ ALLOC index: 4096 order: 11

se i2c pull-low 1. start remap DVR zone 83000000(80580000) 2048...

strength.

[HDmap_done is 0...

MI]: Hotplug Change !!! -1 -> 1 HDMI Cable plugged in. t=402.709
[HDMI]: Turn off HDMI AUDIO
[HDMI]: Send_AudioMute AP_SETUP_H[I2C0] i2c speed changed to 50 KHz

DMI_MUTE=0 Select=1 PS=0
[HDMI]: AP_SETUP_HDMI_MUTE=1
[HDMI]: ~~SetVideoStandard 13 1
Set HDMI Audio Mute(Turn off AUDIO)
[HDMI]: Send_AudioMute() Ok, argp.hdmi_mute=1
[HDMI]: HDCP_XMT_LINK_H0 T=000.000
[HDMI]: HDCP_XMT_LINK_H1 T=000.000

[HDMI]: Read_EDID ST T=000.000
[HDMI]: Set I2C Speed = 50 kHz
[HDMI]: Tx Reads EDID from Rx. ST T=000.004
[HDMI]: Tx Reads EDID from Rx. block=0
Activate

m_browserDevice: 3

WARNING[2]:TVE p-underflow @ line 0
WARNING[2]:TVE i-underflow @ line 49
WARNING[1]:TVE ISR Late i_vcnt =49
2996 SetCurrentBrowserTypeChoice GNewBrowserMenu.cpp 3
GNewBrowserMenu.+++ ALLOC index: 19456 order: 9

cpp:2722, IsBrow1. start remap DVR zone 86c00000(805f8000) 512...

serDirExist() ismap_done is 0...

 false
+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
[HDMI]: Tx Reads EDID from Rx. SP T=000.283
[HDMI]: EDID chksum valid!!! chksum=7936 chksum divide 256=0
[HDMI]: EDID chksum valid!!! chksum=7[ARPC_HDMI_EDID] ena 0x00000001, addr 0x000e6a00
<Audio EDID 1> Version 2 enable
LPCM MaxCH 0x00000002, nBit 0x00000018
SR: 32 44 48
su+pport codec format: 0x00000002
++ ALLOC index: 17672 order: 3

936 chksum divid1. start remap DVR zone 86508000(805ea100) 8...

e 256=0
[HDMI]:map_done is 0...

 HDMI_Device=0
[HDMI]: HDMI_Device=0 => DVI Dev--- FREE index: 17672 order: 3

ice
[HDMI]: Con+++ ALLOC index: 17672 order: 3

tent of EDID:

1. start remap DVR zone 86508000(805ea100) 8...

unsigned char emap_done is 0...

did_data[256]={
0x00,0xff,0xff,--- FREE index: 17672 order: 3

0xff,0xff,0xff,0xff,0x00,0x1e,0x+++ ALLOC index: 19456 order: 9

6d,0x75,0x44,0xc1. start remap DVR zone 86c00000(805f8000) 512...

2,0x4b,0x03,0x00map_done is 0...

,
0x0c,0x11,0x01,0x03,0xea,0x22+++ ALLOC index: 17792 order: 7

,0x1b,0x78,0xea,1. start remap DVR zone 86580000(805eb000) 128...

0x32,0x30,0xa2,0map_done is 0...

x57,0x4a,0x9c,0x25,
0x12,0x50,0x54,0xa5,0x6a,0x80,0x31,0x4f,0x45,0x4f,0x61,0x4f,0x81,0x80,0x01,0x01,
0x01,0x01,0x01,0x01,0x01,0x01,0x30,0x2a,0x00,0x98,0x51,0x00,0x2a,0x40,0x30,0x70,
0x13,0x00,0x52,0x0e,0x11,0x00,0x00,0x1e,0x00,0x00,0x00,0xfd,0x00,0x38,0x4b,0x1e,
0x47,0x0b,0x00,0x0a,0x20,0x20,0x20,0x20,0x20,0x20,0x00,0x00,0x00,0xfc--- FREE index: 19456 order: 9

,0x00,0x4c,
0x3--- FREE index: 17792 order: 7

1,0x37,0x35,0x33,0x54,0x52,0x0a,0x20,0x20,0x20,0x20,0x20,0x00,0x00,0x00,0xfc,
0x00,0x20,0x0a,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x00,0xf9,

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,+++ ALLOC index: 17672 order: 3

0x00,0x00,0x00,01. start remap DVR zone 86508000(805ea100) 8...

x00,0x00,0x00,0xmap_done is 0...

00,0x00,0x00,
0x00,0x00,0x00,0x--- FREE index: 17672 order: 3

00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,};

[HDMI]: Check_HDMI_Device, HDMI_Device=0
[HDMI]: Check_HDMI_Device, HDMI_Device=0
[HDMI]: HDMI-CHIP.cpp:Modify_EDID(7360) ST
original: sum=5=0x5  checksum=5
need 251
sum=256=0x100  checksum=0
[HDMI]: HDMI-CHIP.cpp:Modify_EDID(7399) SP
[HDMI]: No Video Data Block found, VDB_length = 0
---------------------------------------------------
Pixel Clock = 108.000000 MHz
H Active = 1280      V Active = 1024
H Blanking = 1432   V Blanking = 1066
H image size = 338 mm   V image size = 270 mm
Flags = 0x1e   Progressive.   =>   1024p
Get_VID_From_DTD()   W=1280   H=1024   HB=408   VB=42   interlaced=0
GOT VID = 0 = 0x0
-----------------------------------------------------------------
total_data_len=0=0x0
---------------------------------------------------
Pixel Clock = 7.700000 MHz
H Active = 0      V+++ ALLOC index: 19456 order: 8

 Active = 0
H B1. start remap DVR zone 86c00000(805f8000) 256...

lanking = 0   V Blmap_done is 0...

anking = 0
H im+++ ALLOC index: 17728 order: 6

age size = 0 mm   1. start remap DVR zone 86540000(805ea800) 64...

V image size = 0 mm
Flags = 0x0   Progressive.   =>   0p
Get_VID_From_DTD()   W=0   H=0   HB=0   VB=0   interlaced=0
GOT VID map_done is 64...

= 0 = 0x0
-----------------------------------------------------------------
[HDMI]: Check_Detail_Timing_Descriptoins ret=0
[HDMI]: vdb_data_length_old=0 vdb_data_length_new=0
[HDMI]: NO VDB merge needed.
[HDMI]: EDID chksum valid!!! chksum=8192 chksum divide 256=0
[HDMI]: DVI monitor
[HDMI]: Check EDID data SP ret=1
[HDMI]: Read_EDID SP T=000.290

[HDMI]: parseHDMI_EDIDInfo
[HDMI]: Content of ADB in EDID:

unsigned char edid_data[4]={
0x04,0x09,0x07,0x07,};

[HDMI]: Audio Data Block 09 07 07 Format = 0x1 => Linear PCM (e.g., IEC60958)

[HDMI]: ENUM_AUDIO_EDID_ENABLE(--- FREE index: 19456 order: 8

Really send ADB --- FREE index: 17728 order: 6

to AUDIO FW.)
[+++ ALLOC index: 17672 order: 3

HDMI]: AUDIO fir1. start remap DVR zone 86508000(805ea100) 8...

mware version = map_done is 8...

333437 Version=2   new RPC Version--- FREE index: 17672 order: 3

 2
[HDMI]: call_RPC_TOAGENT_HDMI_OUT_EDID_SVC enable=1 NEW
[HDMI]: GetVidNameByTV   =>  VIDEO_HD720_60HZ   VIDEO_PROGRESSIVE   => 720p 60Hz
[HDMI] HDMI_thread(403) call setHDMIAudioVideoFormat()
[HDMI] VID = 0x4   720p 60Hz
[HDMI]: Turn off HDMI
[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Mars
[HDMI] check EDID structure !!!!
[HDMI]: TVSupportxvYCC = 0
[HDMI]: TVSupportxvYCC = 0, do not send metadata.
[HDMI]: Turn on HDMI for DVI................... 1 s_freq=0 c_cnt=0 t=403.159
[HDMI]: TVSupportYCbCr = 0
[HDMI]: NO YCbCr
[HDMI]: TVSupportDeepColor = 0
[HDMI]: This TV does not support Deep Color Mode.
[HDMI]: TVSupportDeepColorYCbCr444 = 0
[HDMI]: This TV does not support YCbCr444 in Deep Color Modes.
[HDMI]: DVI mode for RGB 1...................... 2 s_freq=3 c_cnt=1 t=403.160
[HDMI]: Disable audio setting by video.
[HDMI]: TVSupportxvYCC = 0, do not send metadata.
[HDMI]: Tell AUDIO firmware, now is HDMI_Video_Format_HD
[HDMI]: Send_Video_Format_To_Audio(1)
[HDMI]: argp.video_type=1
[HDMI]: Clear AVMute
[HDMI]: TURN ON HDMI PHY for Mars
[HDMI]: GetVidNameByTV   =>  VIDEO_HD720_60HZ   VIDEO_PROGRESSIVE   => 720p 60Hz
[HDMI]: Setup a wider window of opportunity.
[HDMI]: HDMI_TMDS_SCR1     0x8ca0f0
[HDMI]: HDMISwitchTVSystem SP. t=403.163

[HDMI]: GetVidNameByTV   =>  VIDEO_HD720_60HZ   VIDEO_PROGRESSIVE   => 720p 60Hz
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272520464
[GBrowserAP.cpp:526]:GiveUpFocus()- %%%%%% - !!
IN : /tmp/net
Create /tmp/net Ok!!!
In my system...
GNewBrowserMenu.+++ ALLOC index: 19456 order: 9

cpp:2722, IsBrow1. start remap DVR zone 86c00000(805f8000) 512...

serDirExist() ismap_done is 0...

 false
+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 81...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 9

1. start remap DVR zone 86c00000(805f8000) 512...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 8

1. start remap DVR zone 86c00000(805f8000) 256...

map_done is 0...

+++ ALLOC index: 17728 order: 6

1. start remap DVR zone 86540000(805ea800) 64...

map_done is 64...

--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 8...

--- FREE index: 17672 order: 3

m_hDisplaySurface from OsdManagerTopView::showOSD function = 272520464
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272520464
[GBrowserAP.cpp:526]:GiveUpFocus()- %%%%%% - !!
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
m_hDisplaySurfac+++ ALLOC index: 19456 order: 9

e from OsdManage1. start remap DVR zone 86c00000(805f8000) 512...

rTopView::showOSmap_done is 0...

D function = 272519144
GNewBrow+++ ALLOC index: 17792 order: 7

serMenu.cpp:27221. start remap DVR zone 86580000(805eb000) 128...

, IsBrowserDirExmap_done is 0...

ist() is false
--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 9

1. start remap DVR zone 86c00000(805f8000) 512...

map_done is 0...

+++ ALLOC index: 17792 order: 7

1. start remap DVR zone 86580000(805eb000) 128...

map_done is 0...

--- FREE index: 19456 order: 9

--- FREE index: 17792 order: 7

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

+++ ALLOC index: 19456 order: 8

1. start remap DVR zone 86c00000(805f8000) 256...

map_done is 0...

+++ ALLOC index: 17728 order: 6

1. start remap DVR zone 86540000(805ea800) 64...

sata1: reset phy extra!

sata phy reset

map_done is 0...

--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

+++ ALLOC index: 17672 order: 3

1. start remap DVR zone 86508000(805ea100) 8...

map_done is 0...

--- FREE index: 17672 order: 3

m_hDisplaySurface from OsdManagerTopView::showOSD function = 272520464
m_hDisplaySurface from OsdManagerTopView::showOSD function = 272520464
Init--AbstractAP.cpp--1766-------chenal 0927-----btsamba_info
In my system...
In my system...
[WT] Device number=0
In my system...
Algorithmics/MIPS FPU Emulator v1.5

In my system...
In my system...
In my system...
In my system...
Error in threshold value: 0...
WatchDog does not receive signal for 2 seconds, value: 0
[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[HDMI]: Seup HDMI HPD GPIO.
[HDMI]: Setup_HPD_GPIO, de-bounce = 10 ms Mars
[cfyeh] set PPE = 0

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

usb 1-1: new high speed USB device using ehci_hcd and address 2

In my system...
This is the current time: PowerUP_Done!!!

Audio version number: 333437


Video version number: 332222



[sjg] debug --->> <main.cpp> main():810
 into main function ........
 Get GPIO 76
Get GPIO 74
Get GPIO 73
Get GPIO 72
Get GPIO 71
MSDL_ZHU:AbstractAP.cpp(msdl_thread_func)[7247]:-==-->
hub 1-1:1.0: USB hub found

hub 1-1:1.0: 4 ports detected

hub : ganged power switching

hub : global over-current protection

2336 OnSelect GNewBrowserMenu.cpp 3
[System2ApDaemon.cpp,threadSys2ApExe,156]ms+++ ALLOC index: 19456 order: 8

g type = 6 ,msg 1. start remap DVR zone 86c00000(805f8000) 256...

len = 5 ,msg = 3map_done is 0...

1 20 55 50 00 00+++ ALLOC index: 17728 order: 6

 00 00
Hotplug1. start remap DVR zone 86540000(805ea800) 64...

 got one USB Hotplug of "Add" from port "1".
map_done is 60...

retval: 0


AP:GBrowserAP , cmd_buffer.type:17

[sjg] debug --->> <main.cpp> main():927
 <[sjg] AP:GBrowserAP , ProcessKey retval=0,  cmd_buffer.type:17
 .idApp=ffffffff, parm[0]=00000000>
 AP:GBrowserAP , cmd_buffer.type:4

[sjg] debug --->> <main.cpp> main():927
 <[sjg] AP:GBrowserAP , ProcessKey retval=0,  cmd_buffer.type:4
 .idApp=ffffffff, parm[0]=00000015>
watchdog test pid 190, threshold: 50
sata1: reset phy extra!

sata phy reset

watchdog test pid 190, threshold: 50
--- FREE index: 19456 order: 8

--- FREE index: 17728 order: 6

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata1: reset phy extra!

sata phy reset

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata1: phy reset timeout!

sata1: no device found (phy stat 00000000)

sata1: ata_bus_probe failed

scsi1 : SATA_DRV

sata dma reset

watchdog test pid 190, threshold: 50
sata2: reset phy again!

sata phy reset

watchdog test pid 190, threshold: 50
sata2: reset phy again!

sata phy reset

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
sata2: phy reset timeout!

sata2: no device found (phy stat 00000000)

sata2: ata_bus_probe failed

watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50
watchdog test pid 190, threshold: 50


Я еще попробовал оживить второго пациента, в итоге он висит при включении на заставке с синим фоном HDTV player exslusive а в консоле останавливается на Please press Enter to activate this console. Hotplug: device "loop0" is skipped. и далее список девайсов
лог с консоли второго апарата | +
Code: Select all
?hello  world!
5258028 0 wwaaitiA
REALTEK ROM Monitor, Revision 0000.0202.1019L.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      Feb 15 2012  09:25:38  /0000.0202.1019L

MAC address =                   00.11.22.33.44.55

Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision =         0x93 / 0x78

Endianness =                    Little
Flash memory size =             256 MByte

SDRAM size =                    128 MByte

First free SDRAM address =      0x8010d000


Press 'ESC' to Monitor mode

Signature(яяяяяяяя) error! Entering rescue linux...

Rescue kernel in FLASH, total size = 0xef9f1



            seg.1 addr 0xa0a097e4, size = 0xef9f1



            seg.2 addr 0x0, size = 0x0

copy rescue0: from a0a097e4 to 81000000, len = ef9f1

decompressing rescue: from 81000000 to 80100000: size = ef9f1

lzma finished

decompressing rescue done

go 0x80100000 BOOT_TAG=яяяяяяяя

PAL logo

Reset Ethernet Mac.




Address = 0x80100000


Realtek LINUX (DC ALIAS) started...
Venus setting:
   ROSs have 2621440 bytes RAM.
   System CPU has 1 UART.
   System CPU uses external timer interrupt.
   Bootloader version: 0000.0202.1019L. This version string is of new format.
   The information of this board: Company ID:0x0    CPU ID: 0x12    Board ID: 0x202
   Ethernet Mac address: 00.11.22.33.44.55
   Model Config length=0
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (alan@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.01-20051114) #23 Tue Oct 6 10:10:27 CST 2009

**************************************************************

You didn't specify audio image address, use default instead...

**************************************************************

audio addr: 0

CPU revision is: 00019378

Determined physical RAM map:

 memory: 00100000 @ 00000000 (usable)

 memory: 0032c000 @ 00100000 (reserved)

 memory: 01954000 @ 0042c000 (usable)

 memory: 00280000 @ 01d80000 (reserved)

 memory: 06000000 @ 02000000 (usable)

  show info: max_low_pfn:32768

  show info: min_low_pfn:1068

Built 1 zonelists

Kernel command line: BOOT_TAG=яяяяяяяя console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Estimate value: CPU frequency 405.03 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 123124k/125264k available (1941k kernel code, 2112k reserved, 294k data, 420k init, 0k highmem)

Warning! Unknown board id.

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction...  available.

Linux NoNET1.0 for Linux 2.6

SCSI subsystem initialized

usbcore: registered new driver hub

se init module major number = 254

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

   Hello, Realtek TLB Mapper

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x0

NTFS driver 2.1.28 [Flags: R/O].

Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

Mars no support IDE

 ide generic info: ide_generic_init

Mars no support IDE

libata version 1.12 loaded.

sata driver initial...2009/09/03

sata dma reset

sata1: reset phy again!

sata phy reset

sata1: reset phy again!

sata phy reset

sata1: reset phy extra!

sata phy reset

sata1: reset phy extra!

sata phy reset

sata1: reset phy extra!

sata phy reset

sata1: phy reset timeout!

sata1: no device found (phy stat 00000000)

sata1: ata_bus_probe failed

scsi0 : SATA_DRV

sata dma reset

sata2: reset phy again!

sata phy reset

sata2: reset phy again!

sata phy reset

sata2: phy reset timeout!

sata2: no device found (phy stat 00000000)

sata2: ata_bus_probe failed

scsi1 : SATA_DRV

VenusSFC MTD init

serial flash inaccessible

physmap flash device: 10000000 at fd00000

Realtek NAND Flash Driver Rev:268236 (2009-09-17)

One HY27UF082G2B chip has 1 die(s) on board

nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

[0] (0, 190, 0, 2047)

[1] (0, 958, 0, 2046)

RTK: using the whole nand as a partitoin

Realtek Nand Flash Driver is successfully installing.

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[cfyeh] set PPE = 0

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

Setting registers , Enable OTG

dwc_otg: version 2.60a 22-NOV-2006

DWC_otg: Shared Tx FIFO mode

i2c /dev entries driver

=========================

= VER : 1.8               

=========================

= PHY : 0               

= MODE: MARS               

DWC_otg: USB RESET

= SPD : 1               

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 8     

= RX FIFO DEPTH : 8     

= FIFO THRESHOLD: 4     

= BUS JAM RECORVER : ON 

= NON STOP WRITE : OFF 

= SP PROTECT : ON 

=========================

FATAL : I2C 1 pins have been occupied by PCI

Trying to free free IRQ3

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 420k freed


init started:  BusyBox v1.1.3 (2009.10.06-02:08+0000) multi-call binary

Starting pid 332, console /dev/console: '/etc/init.d/rcS'
120+0 records in
120+0 records out
Welcome to Realtek Rescue Linux for PhotoViewer
mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: Unknown error 19
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2

>>>>>> loader start! (Oct  6 2009:10:09:51, version=00.01.01)

Please press Enter to activate this console. Hotplug: device "loop0" is skipped.
Hotplug: device "loop1" is skipped.
Hotplug: device "loop2" is skipped.
Hotplug: device "loop3" is skipped.
Hotplug: device "loop4" is skipped.
Hotplug: device "loop5" is skipped.
Hotplug: device "loop6" is skipped.
Hotplug: device "loop7" is skipped.
Hotplug: device "ram0" is skipped.
Hotplug: device "mtdblock0" is skipped.

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 16 Apr 2012, 12:23
by Virtual
HDTV player exslusive бут не грузит прошивку с корнем в сквош! (специально не стал исправлять ибо нефиг)

Rescue kernel in FLASH, total size = 0xef9f1
....
Hotplug: device "loop0" is skipped
и т.д. о режиме rescu тоесть ожидается флешка с прошивкой :)., суньте ему нашу AMP должен сожрать как миленький.

Включается через раз - при включении выбивает автоматом на приглашение s/d/g/c> или обыкновенно грузится и включается

тоже словил нечто похожее., иногда на холодную при долгом сьеме питания первое включение и так -же вышибает., но это только на одном самом древнем аппарате и с вусмерть замученной флеш....пока не могу найти закономерности....но это происходжит именно когда плеер остывший., имхо гдет непропай.

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 18 Apr 2012, 10:31
by RomZESS5
На HDTV player exslusive не смог поставить прошивку, флеху не видит хоть ты тресни, думаю хаб сдох, решил поискать замену GL850A в ненужных хабах, да там везде FE1.1 а у них распиновки разные((( пока в поисках замены.

Virtual wrote:тоже словил нечто похожее., иногда на холодную при долгом сьеме питания первое включение и так -же вышибает., но это только на одном самом древнем аппарате и с вусмерть замученной флеш....пока не могу найти закономерности....но это происходжит именно когда плеер остывший., имхо гдет непропай.

Действительно непропай либо отвалилось чтото, прошолся феном под 400 градусов по чипам, думал что пережарил а то как то подозрительно плата начала дымится и шипеть))) но в итоге стал запускаться без проблем, всегда с первого раза и тормоза пропали!!!! все как бе хорошо, но хотелось бы вернуть заставочку konoos при включении, а то асус как то не в тему, мне интесено где вы нарыли буткоды? производитель предоставил или сами?

Re: Konoos GV3765 (RTD1073DD)

PostPosted: 18 Apr 2012, 14:27
by Virtual
На HDTV player exslusive не смог поставить прошивку, флеху не видит хоть ты тресни, думаю хаб сдох, решил поискать замену GL850A в ненужных хабах, да там везде FE1.1 а у них распиновки разные((( пока в поисках замены.

хм интересно.... но насколько мне не изменяет память, на плеерах с хабом есть похоже нога управления ентим хабом. нужно узнать какая.
//т.к. у меня нет ни одного плеера с хабом (бог миловал :mrgreen: ), нужны данные (карта IO):
в телнет консоли (когда стоит флешка и определяется)
Code: Select all
stopall
03

Вопросы по Медиаплеер Konoos GV-3765

PostPosted: 24 Mar 2013, 16:34
by Rollek
Добрый день у меня такой вопрос такой заходя в плеер через Total Commander FTP есть папка temp (вопрос ей также как и в ПК нужно очищать ?)

Re: Вопросы по Медиаплеер Konoos GV-3765

PostPosted: 24 Mar 2013, 17:24
by Pokrass
нет - она читстится при перезагрузке. По сути - это оперативная память устройства.