Восстановление при самой неудачной прошивке Saturn(1186)

о железе плеера и о периферии

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Densys » 24 Jul 2020, 16:28

Спасибо за подсказку. Файлы нашел.

Rescue починилась. Но это особо не помогло.
Она пыталась починить все штатно . но у неё не получилось.

Если интересно вот лог.
Code: Select all
Linux version 2.6.34-VENUS (william@rtdmpsa-05) (gcc version 4.3.6 20110218 (prerelease) (GCC) ) #21 PREEMPT Wed Dec 4 13:08:14 CST 2013

Realtek LINUX started...
Venus setting:
        ROSs have 4194304 bytes RAM.
        System CPU has 1 UART.
        System CPU uses internal timer interrupt.
        Bootloader version: KIIE.0402.1067. This version string is of new format.
        The information of this board: Company ID:0x0    CPU ID: 0x4    Board ID: 0x402
        Ethernet Mac address: 00.11.22.33.44.55
        Model Config length=3
Base year of RTC is 2010.
**************************************************************
You didn't specify audio image address, use default instead...
**************************************************************
audio addr: 0
Config serial console: console=ttyS0,115200n8r
bootconsole [early0] enabled
CPU revision is: 00019385 (MIPS 24Kc)
FPU revision is: 01739300
Determined physical RAM map:
 memory: 00020000 @ 00000000 (reserved)
 memory: 000e0000 @ 00020000 (ROM data)
 memory: 01b00000 @ 00100000 (usable)
 memory: 00400000 @ 01c00000 (reserved)
 memory: 0e000000 @ 02000000 (usable)
 memory: 00100000 @ 10000000 (reserved)
 memory: 07f00000 @ 10100000 (usable)
 memory: 00100000 @ 18000000 (reserved)
 memory: 05b00000 @ 18100000 (usable)
Wasting 8192 bytes for tracking 256 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  DMA      0x00000000 -> 0x00002000
  Normal   0x00002000 -> 0x0001dc00
Movable zone start PFN for each node
  Node 0: 64512
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x0001dc00
zone DMA        size: 2000      realsize: 2000
zone Normal     size: dc00      realsize: dc00
zone Movable    size: e000      realsize: e000
zonelist: Movable Normal DMA
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 121856
Kernel command line:  console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00056730
Readback ErrCtl register=00056730
Memory: 468824k/480256k available (3506k kernel code, 11432k reserved, 852k data, 2600k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:8
Estimated CPU frequency: 796.54 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 529.20 BogoMIPS (lpj=2646016)
Mount-cache hash table entries: 512
devtmpfs: initialized
NET: Registered protocol family 16
prom_flashsize = 0x100000000
Flash size is 0x2000000
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource MIPS-DMP
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Switched to NOHz mode on CPU #0
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.




 *****************    se init module  *********************



se init module major number = 253




 *****************    md init module  *********************



md init module major number = 252
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
init_vdso successfull
rtktlb: Hello, Realtek TLB Mapper...
   AllocBP size: 688128 order: 8 offset: 0
        <<<DVR FREE AREA>>>
        0:      0
        1:      0
        2:      0
        3:      0
        4:      0
        5:      0
        6:      0
        7:      0
        8:      0
        9:      0
        10:     0
        11:     0
        12:     0
        13:     7
                Addr: 82000000, order: 13
                Addr: 84000000, order: 13
                Addr: 86000000, order: 13
                Addr: 88000000, order: 13
                Addr: 8a000000, order: 13
                Addr: 8c000000, order: 13
                Addr: 8e000000, order: 13
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 915
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Realtek Bulid-In SATA Driver Rev:SATURN (2011-02-24 15:10)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA PackageRealtek NAND Flash Driver Rev:337905 (2010-10-18)
(X)Enable interrupt mechanism of NAND driver.
Get parameter from register...
[rtk_nand_init]Bootcode size 0x3200000
[rtk_nand_init]Factory parameter size 0x400000
[rtk_nand_init]Disable NFCP...
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
Detect H27UBG8T2B and enable read-retrial mode...
Enable Read-retrial mode...
Enable Randomized mechanism
READ ID:0xad 0xd7 0x94 0xda 0x74 0xc3
One H27UBG8T2B chip has 1 die(s) on board
nand part=H27UBG8T2B, id=add794da, device_size=4294967296, chip_size=4294967296, num_chips=1, page_size=8192, isLastPage=1, eccBits=24
[rtk_nand_scan_bbt] have created bbt B1, just loads it !!
[dump_BBT] Nand BBT Content
[0] (0, 27, 0, 2047)
RTK: using the whole nand as a partitoin
[rtk_nand_init]Randomized enabled
 [rtk_nand_init]Ecc bit select 24
Realtek Nand Flash Driver is successfully installing.
VenusSFC MTD init...
NOR flash support list ..
(X) HWSEMA support.
(V) AUTO_HW_POLL support.
(X) 4Bytes mode support.
(V) Max erase size support.
(V) Sfc_delay support.
[venus_sfc_init]FLASH_BASE: 0xbdc00000
[venus_sfc_init]Flash size: 0x2000000
Read id orginal value : 0xc22015c2
--RDID Seq: 0xc2 | 0x20 | 0x15
VenusSFC MTD: MXIC MX25L1605 detected.
SFC_4KB_ERASE
VenusSFC MTD: Enable VenusSFC MD PP callback function.
MD_READ Enable..
MD_WRITE Enable..
[venus_sfc_init]descriptor size 0x2000000
RedBoot partition parsing not available
Venus SFC: using single partition Venus SFC: (for SST/SPANSION/MXIC SPI Flash)
this  Jupiter eth RX_OFFSET = 0x0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
MAC address = 0x00.11.22.33.44.55
eth0: RTL-8139C+ at 0xb8016000, 00:11:22:33:44:55, IRQ 2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(861) 0xb8013808 = 0x4400a081
#@# cfyeh-debug USBPHY_Register_Setting(863) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(933)
#@#[cfyeh-debug] USBPHY_Register_Setting(935)
#@#[cfyeh-debug] USBPHY_Register_Setting(937)
#@# cfyeh-debug USBPHY_SetReg_Default_39(289) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ehci ehci: Rtk Dmp EHCI
ehci ehci: new USB bus registered, assigned bus number 1
ehci ehci: irq 2, io mem 0xb8013000
Hotplcp_hotplug
ug got one Net Hotplug of "Add" from "eth0". It may be Realtek's wireless device.
ehci ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(861) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_Register_Setting(863) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(933)
#@#[cfyeh-debug] USBPHY_Register_Setting(935)
#@#[cfyeh-debug] USBPHY_Register_Setting(937)
#@# cfyeh-debug USBPHY_SetReg_Default_39(289) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ohci ohci: Rtk Dmp OHCI
ohci ohci: new USB bus registered, assigned bus number 2
ohci ohci: irq 2, io mem 0xb8013400
ata1: SATA link down (SStatus 0 SControl 300)
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
#@# cfyeh-debug usb3_phy_setting_saturn(38) +++
#@# cfyeh-debug usb3_phy_setting_saturn(227) ---
xhci xhci: Rtk Dmp XHCI
xhci xhci: new USB bus registered, assigned bus number 3
xhci xhci: irq 2, io mem 0xb8020000
#@# cfyeh-debug xhci_irq(1747) 0x000002a0 0x002802a0
#@# cfyeh-debug handle_port_status(1096) 0x000002a0 0x002802a0
#@#[cfyeh-debug] handle_port_status(1124) NOT in U0
usb usb3: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
#######[cfyeh-debug] hub_events(3615) usb_plug_status 1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
#@# cfyeh-debug xhci_hub_control(287) hack for usb3 portsc
#@# cfyeh-debug usb3_mac_setting_saturn(232) +++
#@# cfyeh-debug usb3_mac_setting_saturn(253) 16bit
#@# cfyeh-debug usb3_mac_setting_saturn(254) *(unsigned int volatile *)0xb8028200=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(255) *(unsigned int volatile *)0xb8028200=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(257) *(unsigned int volatile *)0xb8028200=0x2400
#@# cfyeh-debug usb3_mac_setting_saturn(268) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(270) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(274) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(275) 0xb8028108 = 0x02400008
#@# cfyeh-debug usb3_mac_setting_saturn(280) 0xb8028108 = 0x21010000
#@# cfyeh-debug usb3_mac_setting_saturn(283) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(284) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(289) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(294) disable usb mulit request
#@# cfyeh-debug usb3_mac_setting_saturn(295) *(unsigned int volatile *)0xb8013200=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(297) *(unsigned int volatile *)0xb8013200=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(302) GUSB3PIPECTL
#@# cfyeh-debug usb3_mac_setting_saturn(303) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(306) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(309) ---
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 0
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
usb 1-1: new high speed USB device using ehci and address 2
[I2C1] i2c speed changed to 100 KHz
I2C1 Bus Status Check.... OK
=========================
= VER : 2.1b
=========================
= PHY : 1
= MODEL: Saturn
= SPD : 100
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32
= RX FIFO DEPTH : 32
= FIFO THRESHOLD: 4
= BUS JAM RECORVER 3: ON
= NON STOP WRITE : ON
= GPIO RW SUPPORT : ON
=========================
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
Hotplug gNET: Registered protocol family 17
ot one Net Hotplug of "Add" from "sit0". It may be Realtek's wireless device.
scsi1 : usb-storage 1-1:1.0
#######[cfyeh-debug] hub_events(3619) usb_plug_status 0
#######[cfyeh-debug] usb_stor_scan_thread(841) usb_plug_status 1
cp_open
alloc rings cp->rxdesc_buf =0xb0212000 , cp->ring_dma=0x10212000
init_hw

 eth0: Set multicast.
jupiter/saturn 1g
init_hw finished

 eth0: Set multicast.

 eth0: Set multicast.

 eth0: Set multicast.
ADDRCONF(NETDEV_UP): eth0: link is not ready
#######[cfyeh-debug] usb_stor_scan_thread(869) usb_plug_status 2
scsi 1:0:0:0: Direct-Access     UFD 2.0  Silicon-Power4G  1100 PQ: 0 ANSI: 0 CCS
#@#[cfyeh-debug] sd_probe(2278) sd_flag 1
#@#[cfyeh-debug] sd_probe(2344) sd_flag 0
#@#[cfyeh-debug] sd_probe_async(2186) sd_flag 1
#@#[cfyeh-debug] sd_revalidate_disk(2061) sd_flag 2
#######[cfyeh-debug] usb_stor_scan_thread(872) usb_plug_status 1
#######[cfyeh-debug] usb_stor_scan_thread(879) usb_plug_status 0
IP-Config: Complete:
     device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
     host=192.168.0.9, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
modprobe: module sd_mod not found
modprobe: failed to load module sd_mod
sd 1:0:0:0: [sda] 7858176 512-byte logical blocks: (4.02 GB/3.74 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
#@#[cfyeh-debug] sd_revalidate_disk(2120) sd_flag 1
#@#[cfyeh-debug] sd_revalidate_disk(2061) sd_flag 2
sd 1:0:0:0: [sda] Assuming drive cache: write through
#@#[cfyeh-debug] sd_revalidate_disk(2120) sd_flag 1
 sda: sda1
data[0] 0x0 signature[0] 0xbabeface
data[1] 0x0 signature[1] 0xdeadbeef
#@#[cfyeh-debug] sd_revalidate_disk(2061) sd_flag 2
sd 1:0:0:0: [sda] Assuming drive cache: write through
#@#[cfyeh-debug] sd_revalidate_disk(2120) sd_flag 1
sd 1:0:0:0: [sda] Attached SCSI removable disk
#@#[cfyeh-debug] sd_probe_async(2245) sd_flag 0
Freeing prom memory: 896k freed
Freeing unused kernel memory: 2600k freed
Welcome to Realtek Rescue Linux for PhotoViewer
/etc/init.d/rcS: line 49: cannot create /sys/bus/usb/devices/usb1/bEnableHubOnBoard_woone: nonexistent directory
mount: mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such device
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such device

Please press Enter to activate this console. #@#[cfyeh-debug] check_boot_code_size(1085) nand_boot_size 0x3200000
#@#[cfyeh-debug] check_boot_code_size(1091) factory_size 0x400000

>>>>>> loader start! (Dec  4 2013:13:08:04, version=00.01.01)
#@#[cfyeh-debug] check_boot_code_size(1085) nand_boot_size 0x3200000
#@#[cfyeh-debug] check_boot_code_size(1091) factory_size 0x400000
get_mtd_block_name(/dev/mtdblock0)
[JH] checksignatue(), open(/dev/mtdblock0) nand_boot_size(0x3200000) factory_size(0x400000)
fail 4, sig(VERO)
no IMG_XXXX signature found
BUS_TYPE = (null)
Hotplug: device "ram0" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram1" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram3" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram5" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram6" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram7" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram8" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram2" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram4" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram12" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram11" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram10" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram9" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram13" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram14" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram15" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop0" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop3" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop5" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop6" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop2" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop7" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock0" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock1" is skipped.
rmdir: '/var/lock/hotplug/mount_tmp/.sda1': No such file or directory
BUS_TYPE = (null)
Hotplug: device "loop4" is skipped.
mount: mounting /dev/sda1 on /var/lock/hotplug/mount_tmp/.sda1 failed: No such device
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

 eth0: Set multicast.
hotplug eth0: link up, 100Mbps, full-duplex
Hotplug got one Net Hotplug of "LinkUP" from "eth0".
mount: mounting /dev/sda1 on /var/lock/hotplug/mount_tmp/.sda1 failed: No such device
mount: mounting /dev/sda1 on /var/lock/hotplug/mount_tmp/.sda1 failed: No such deNTFS-fs warning (device sda1): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
vice
mount: mounting /dev/sda1 on /var/lock/hotplug/mount_tmp/.sda1 failed: Invalid arguFAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
ment
BUS_TYPE = usb
Hotplug: mount -t ufsd -o force,ro,nls=utf8,umask=0,noatime /dev/sda1 /var/lock/hotplug/mount_tmp/.sda1 ret: 255
Hotplug: mount -t ntfs -o ro,iocharset=utf8,umask=0 /dev/sda1 /var/lock/hotplug/mount_tmp/.sda1 ret: 255
Hotplug: mount -t vfat -o ro,shortname=winnt,iocharset=utf8,umask=0 /dev/sda1 /var/lock/hotplug/mount_tmp/.sda1 ret: 0
Hotplug: Mount "sda1" successfully.
build_imgfile_list: namelist[n]->d_name: .
build_imgfile_list: namelist[n]->d_name: ..
build_imgfile_list: namelist[n]->d_name: install.img
(pattern_byte ==pattern_comparing11
[loader_a.c][verona_load_func][1679]Debug USB Install(path:/mnt/usbmounts/sda1)
totallistcount: 1
img_list[first_big_useful_index].filename: /mnt/usbmounts/sda1/install.img
tar: UI: not found in archive
command: tar -xOf /mnt/usbmounts/sda1/install.img install_a > /install_a
**************************************************************************
Saturn install_a (JH version), date:Dec 24 2013, time:10:25:37 REV:612471
**************************************************************************
argc:2, argv[0]=/install_a, argv[1]=/mnt/usbmounts/sda1/install.img
opt_str=(null) , tgt_dev=(null), compress_srting=(null)
package_file_path:/mnt/usbmounts/sda1/install.img
[INSTALL INFO][./src/rtk_mtd.cpp][44] Open MTD_CHAR /dev/mtd0
[INSTALL LOG][./src/rtk_imgdesc.cpp][66]
support MEMDISABLESCRAMBLE
[INSTALL INFO][./src/rtk_mtd.cpp][62] Open MTD_BLOCK /dev/mtdblock0
[INSTALL LOG][./src/rtk_fwdesc.cpp][767]
nand_boot_size 0x3200000
[INSTALL LOG][./src/rtk_fwdesc.cpp][773]
factory_size 0x400000
[INSTALL LOG][./src/rtk_imgdesc.cpp][101]
MEMINFO flash_type:4 flash_size:0x100000000(4194304 KB = 4096 MB) mtd_erasesize:0x00200000 (2048 KB), page_size:0x00002000
[INSTALL INFO][./src/rtk_main.cpp][136] prtkimgdesc->tarinfo.tarfile_path:/mnt/usbmounts/sda1/install.img(0x3fc75870)
[INSTALL LOG][./src/rtk_tar.cpp][108]
NULL:0 ZERO:0, prtkimg->tarinfo.tarfile_path=/mnt/usbmounts/sda1/install.img(0x3fc75870)
tarfile_path:/mnt/usbmounts/sda1/install.img, tarfile_size: 215289856 Bytes (210244 KB)
[INSTALL LOG][./src/rtk_tar.cpp][50]
hash_value :
0x13 0x2E 0x5E 0x52 0xFFD5 0x5D 0xFFEF 0x7B 0x08 0xFF92 0x5A 0x6F 0xFF92 0x1B 0xFFDE 0x76
current tarfile_offset:0

filename=arial.ttf, filezie=143300 (139KB), ustarin=ustar
Tarfile parsing offset:0 (0x00000000)
current tarfile_offset:143872

filename=configuration.xml, filezie=2314 (2KB), ustarin=ustar
Tarfile parsing offset:143872 (0x00023200)
[INSTALL LOG][./src/rtk_imgdesc.cpp][579]
Got configuration.xml
current tarfile_offset:146944

filename=flash_erase, filezie=47504 (46KB), ustarin=ustar
Tarfile parsing offset:146944 (0x00023e00)
current tarfile_offset:195072

filename=image/, filezie=0 (0KB), ustarin=ustar
Tarfile parsing offset:195072 (0x0002fa00)
current tarfile_offset:195584

filename=image/update_bg_ok.png, filezie=53749 (52KB), ustarin=ustar
Tarfile parsing offset:195584 (0x0002fc00)
current tarfile_offset:249856

filename=image/update_focus.png, filezie=2871 (2KB), ustarin=ustar
Tarfile parsing offset:249856 (0x0003d000)
current tarfile_offset:253440

filename=image/update_bg.png, filezie=52790 (51KB), ustarin=ustar
Tarfile parsing offset:253440 (0x0003de00)
current tarfile_offset:307200

filename=image/update_unfocus.png, filezie=2871 (2KB), ustarin=ustar
Tarfile parsing offset:307200 (0x0004b000)
current tarfile_offset:310784

filename=image/update_bg_fail.png, filezie=51773 (50KB), ustarin=ustar
Tarfile parsing offset:310784 (0x0004be00)
current tarfile_offset:363520

filename=install_a, filezie=3033700 (2962KB), ustarin=ustar
Tarfile parsing offset:363520 (0x00058c00)
current tarfile_offset:3398144

filename=mkfs.jffs2, filezie=163948 (160KB), ustarin=ustar
Tarfile parsing offset:3398144 (0x0033da00)
current tarfile_offset:3563008

filename=mkyaffs2image, filezie=48052 (46KB), ustarin=ustar
Tarfile parsing offset:3563008 (0x00365e00)
current tarfile_offset:3611648

filename=nandwrite, filezie=61668 (60KB), ustarin=ustar
Tarfile parsing offset:3611648 (0x00371c00)
current tarfile_offset:3674112

filename=package5/, filezie=0 (0KB), ustarin=ustar
Tarfile parsing offset:3674112 (0x00381000)
[INSTALL INFO][./src/rtk_imgdesc.cpp][616] package5/ can't be figured
current tarfile_offset:3674624

filename=package5/vmlinux.develop.android.saturn.nand.bin, filezie=7483204 (7307KB), ustarin=ustar
Tarfile parsing offset:3674624 (0x00381200)
current tarfile_offset:11158528

filename=package5/bootloader.tar, filezie=2457600 (2400KB), ustarin=ustar
Tarfile parsing offset:11158528 (0x00aa4400)
current tarfile_offset:13616640

filename=package5/yaffs2_2.img, filezie=1480512 (1445KB), ustarin=ustar
Tarfile parsing offset:13616640 (0x00cfc600)
current tarfile_offset:15097856

filename=package5/video_firmware.bin, filezie=2357440 (2302KB), ustarin=ustar
Tarfile parsing offset:15097856 (0x00e66000)
current tarfile_offset:17456128

filename=package5/squashfs1.img, filezie=192794624 (188276KB), ustarin=ustar
Tarfile parsing offset:17456128 (0x010a5c00)
current tarfile_offset:210251264

filename=package5/bluecore.audio, filezie=1883184 (1839KB), ustarin=ustar
Tarfile parsing offset:210251264 (0x0c882e00)
current tarfile_offset:212135424

filename=uEGBK.mbf, filezie=747522 (730KB), ustarin=ustar
Tarfile parsing offset:212135424 (0x0ca4ee00)
current tarfile_offset:212883968

filename=video_firmware.install.bin, filezie=2391176 (2335KB), ustarin=ustar
Tarfile parsing offset:212883968 (0x0cb05a00)
current tarfile_offset:215276032
[INSTALL DEBUG][./src/rtk_tar.cpp][152]
tar magic error
command:tar xv -f /mnt/usbmounts/sda1/install.img en_kh.txt, (139) [./src/rtk_main.cpp]
tar: en_kh.txt: not found in archive
[INSTALL DEBUG][./src/rtk_common.cpp][190]
Can't exec command:tar xv -f /mnt/usbmounts/sda1/install.img en_kh.txt, (139) [./src/rtk_main.cpp]
command:tar xv -f /mnt/usbmounts/sda1/install.img rsa_key_tmp.pub, (141) [./src/rtk_main.cpp]
tar: rsa_key_tmp.pub: not found in archive
[INSTALL DEBUG][./src/rtk_common.cpp][190]
Can't exec command:tar xv -f /mnt/usbmounts/sda1/install.img rsa_key_tmp.pub, (141) [./src/rtk_main.cpp]
[INSTALL INFO][./src/rtk_mtd.cpp][101] Open MTD_BLOCK /dev/mtdblock0 with 56623104(0x3600000) offset
fw_table:
e0 2b 10 90 90 36 52 80 00 00 10 00 00 00 00 00
00 00 00 00 02 00 00 00 00 00 00 80 00 00 00 00

[INSTALL DEBUG][./src/rtk_fwdesc.cpp][74]
Wrong boottable version:0x00
[INSTALL DEBUG][./src/rtk_imgdesc.cpp][130]
load_fwdesc() fail

Extract configuration.xml file...
tarfile_offset:0x00023200 (2314 Bytes = 2 KB)
extract configuration.xml from /mnt/usbmounts/sda1/install.img
100 |******************************| 2 KB

total_time:0 secands
extract ok
<?xml version="1.0" encoding="ISO-8859-1" ?>
<packageFile>
    <info>
        <company>Realtek Semiconductor Corp.</company>
        <description>This image file contains 3 Jupiter packages. The first one is for AVHDD on NOR, the second one is for AVHDD on NAND, and the third one is for AVHDD on ISO image.</description>
        <version>v10.1.1.r11725</version>
        <releaseDate>04/20/15 17:06</releaseDate>
        <signature>Saturn image files</signature>
    </info>
    <installerAP>
        <fileName>install_a</fileName>
        <hashValue>4c7fd58c048cde1ecfa1a34c47d1a092</hashValue>
        <install_bootloader>y</install_bootloader>
    </installerAP>
    <package>
        <info>
            <description>This is Android on NAND of Saturn</description>
            <version>N/A</version>
        </info>
        <nand>
            <image type="yaffs2" userDefined="y">
                <fileName />
                <mountPoint>cache</mountPoint>
                <sizeBytesMin>52428800</sizeBytesMin>
            </image>
            <image type="linuxKernel">
                <fileName>package5/vmlinux.develop.android.saturn.nand.bin</fileName>
                <targetAddress>0x80100000</targetAddress>
                <version>SVN:11711</version>
            </image>
            <image type="audioKernel">
                <fileName>package5/bluecore.audio</fileName>
                <targetAddress>0x81b00000</targetAddress>
                <version>N/A</version>
            </image>
            <image type="videoKernel">
                <fileName>package5/video_firmware.bin</fileName>
                <targetAddress>0x81d80000</targetAddress>
                <version>N/A</version>
            </image>
            <image type="bootloader">
                <fileName>package5/bootloader.tar</fileName>
                <version>N/A</version>
            </image>
            <image type="squash">
                <fileName>package5/squashfs1.img</fileName>
                <mountPoint>/</mountPoint>
            </image>
            <image type="yaffs2">
                <fileName>package5/yaffs2_2.img</fileName>
                <mountPoint>/usr/local/etc</mountPoint>
                <sizeBytesMin>1073741824</sizeBytesMin>
            </image>
        </nand>
    </package>
</packageFile>
[INSTALL DEBUG][./src/rtk_imgdesc.cpp][201]
(Audio Bootfile) target address not found!! skip
[INSTALL DEBUG][./src/rtk_imgdesc.cpp][201]
(Video Bootfile) target address not found!! skip
[INSTALL INFO][./src/rtk_imgdesc.cpp][253] prtkimg->option(0x3)etc_partition_size(0x40000000) preserve_partition_size(0x3200000)
[INSTALL DEBUG][./src/rtk_imgdesc.cpp][271]
The size of FW_TYPE:3 is zero!!
flash_type=0x00000004, flash_size=0x0100000000 (4194304 KB), mtd_erasesize=0x00200000, page_size=0x00002000, total_sector=2048
[INSTALL LOG][./src/rtk_imgdesc.cpp][410]

         Kernel flash_ofs:0x0003800000 allo_size:0x00800000 end:0x0004000000 img_size:0x00722f44(  7307 KBytes)(004 sectors)
   Audio kernel flash_ofs:0x0004000000 allo_size:0x00200000 end:0x0004200000 img_size:0x001cbc30(  1839 KBytes)(001 sectors)
   Video kernel flash_ofs:0x0004200000 allo_size:0x00400000 end:0x0004600000 img_size:0x0023f8c0(  2302 KBytes)(002 sectors)
 Audio Bootfile flash_ofs:0x0004600000 allo_size:0x00000000 end:0x0004600000 img_size:0x00000000(     0 KBytes)(000 sectors)
 Video Bootfile flash_ofs:0x0004600000 allo_size:0x00000000 end:0x0004600000 img_size:0x00000000(     0 KBytes)(000 sectors)
         RootFS flash_ofs:0x00a4600000 allo_size:0x0b800000 end:0x00afe00000 img_size:0x0b7dd000(188276 KBytes)(092 sectors)
       Resource flash_ofs:0x00afe00000 allo_size:0x00000000 end:0x00afe00000 img_size:0x00000000(     0 KBytes)(000 sectors)
       Preserve flash_ofs:0x00afe00000 allo_size:0x03200000 end:0x00b3000000 img_size:0x00000000(     0 KBytes)(025 sectors)
  Usr.local.etc flash_ofs:0x00b3000000 allo_size:0x40000000 end:0x00f3000000 img_size:0x00169740(  1445 KBytes)(512 sectors)
       bootcode flash_ofs:0x0000000000 allo_size:0x00000000 end:0x0000000000 img_size:0x00258000(  2400 KBytes)(000 sectors)
ROOTFS:/, USR_LOCAL_ETC:/usr/local/etc

         Kernel target_offset:0x80100000 tarfile_offset:0x00381200
   Audio kernel target_offset:0x81b00000 tarfile_offset:0x0c882e00
   Video kernel target_offset:0x81d80000 tarfile_offset:0x00e66000
 Audio Bootfile target_offset:0xffffffff tarfile_offset:0x00000000
 Video Bootfile target_offset:0xffffffff tarfile_offset:0x00000000
         RootFS target_offset:0x00000000 tarfile_offset:0x010a5c00
       Resource target_offset:0x00000000 tarfile_offset:0x00000000
       Preserve target_offset:0x00000000 tarfile_offset:0x00000000
  Usr.local.etc target_offset:0x00000000 tarfile_offset:0x00cfc600
       bootcode target_offset:0x00000000 tarfile_offset:0x00aa4400

Extract video_firmware.install.bin file...
tarfile_offset:0x0cb05a00 (2391176 Bytes = 2335 KB)
extract video_firmware.install.bin from /mnt/usbmounts/sda1/install.img
100 |******************************| 2335 KB

total_time:0 secands
extract ok

Extract uEGBK.mbf file...
tarfile_offset:0x0ca4ee00 (747522 Bytes = 730 KB)
extract uEGBK.mbf from /mnt/usbmounts/sda1/install.img
100 |******************************| 730 KB

total_time:0 secands
extract ok

Extract image/update_bg_ok.png file...
tarfile_offset:0x0002fc00 (53749 Bytes = 52 KB)
extract image/update_bg_ok.png from /mnt/usbmounts/sda1/install.img
100 |******************************| 52 KB

total_time:0 *** 476MB version...
secands
extract ok

Extract image/updauth: memory address 0x40000000...
ate_foc *****************    se open: queue = 0   *********************
us *****************    se open: initialized = 0  *********************
.pnarch/mips/rtk_dmp/drivers/se.c, 714: offset = 0, se_devices = 90190000
g arch/mips/rtk_dmp/drivers/se.c, 724: offset = 0
fiarch/mips/rtk_dmp/drivers/se.c, 768: length = 20480
learch/mips/rtk_dmp/drivers/se.c, 769: offset = 270073856
..arch/mips/rtk_dmp/drivers/se.c, 776: offset = 270073856
arch/mips/rtk_dmp/drivers/se.c, 714: offset = 98316, se_devices = 90190000

arch/mips/rtk_dmp/drivers/se.c, 724: offset = 402702336
taarch/mips/rtk_dmp/drivers/se.c, 768: length = 4096
rfarch/mips/rtk_dmp/drivers/se.c, 769: offset = 402702336
ilarch/mips/rtk_dmp/drivers/se.c, 776: offset = 402702336
e_offset:0x0003d000 (2871 Bytes = 2 KB)
extract image/update_focus.png from /mnt/usbmounts/sda1/install.img
100 |******************************| 2 KB

total_time:1 secands
extract ok

Extract image/update_bg.png file...
tarfile_offset:0x0003de00 (52790 Bytes = 51 KB)
extract image/update_bg.png from /mnt/usbmounts/sda1/install.img
93 |***************************   | 4=== GET HWSEM...
100 |******************************| 51 KB

total_time:0 secands
extract ok

Extract image/update_unfocus.png file...
tarfile_offset:0x0004b000 (2871 Bytes = 2 KB)
extract image/update_unfo=== GET HWSEM...
cus.png from /mnt/usbmounts/sda1/install.img
100 |******************************| 2 KB

total_time:0 secands
extract ok

Extract image/update_bg_fail.png file...
tarfile_offset:0x0004be00 (51773 Bytes = 50 KB)
extract image/update_bg_fail.png from /mnt/usbmounts/sda1/install.img
100 |******************************| 50 KB

total_time:0 secands
extract ok
pli initialization...
call pli_init, return 0
pli_getStartAddress() return 0x40000000
start[0-3] = {7ff1a500}
end[0-3] = {7ff1a504}
**chip_id = 1186
chip_id&0xF =0x6
SB2 DEBUG CONTROL(0)= 0x0 --> 0x0
SB2 DEBUG CONTROL(1)= 0x0 --> 0x0
SB2 DEBUG CONTROL(2)= 0x0 --> 0x0
SB2 DEBUG CONTROL(3)= 0x0 --> 0x0
SB2 DEBUG CONTROL(4)= 0x0 --> 0x0
SB2 DEBUG CONTROL(5)= 0x0 --> 0x0
SB2 DEBUG CONTROL(6)= 0x0 --> 0x0
SB2 DEBUG CONTROL(7)= 0x0 --> 0x0
SB2 INT = 0x0 --> 0x0
SB2 start addr(0)= 0x0 --> 0x0
SB2 end addr(0)= 0x0 --> 0x0
SB2 start addr(1)= 0x0 --> 0x0
SB2 end addr(1)= 0x0 --> 0x0
SB2 start addr(2)= 0x1d80000 --> 0x0
SB2 end addr(2)= 0x1ffdfff --> 0x0
SB2 start addr(3)= 0x1d80410 --> 0x0
SB2 end addr(3)= 0x1ed3a10 --> 0x0
SB2 start addr(4)= 0x2000000 --> 0x0
SB2 end addr(4)= 0x24ef7ff --> 0x0
SB2 start addr(5)= 0x0 --> 0x0
SB2 end addr(5)= 0x0 --> 0x0
SB2 start addr(6)= 0x0 --> 0x0
SB2 end addr(6)= 0x0 --> 0x0
SB2 start addr(7)= 0x0 --> 0x0
SB2 end addr(7)= 0x0 --> 0x0
IS_CHIP(SATURN)
Saturn...

 got //video_firmware.install.bin
video start addr, ptr=0x41d80000
video image size, cnt=2391176

audio_addr = 0xb081

video_addr = 0xd881

 sleep for 3 seconds...

C[RPC]open for RPC ioctl...
al[RPC]start reset...
li[RPC]done...
n  pli_resetRPC()...

Release SW Semaphore.
command:rm -rf /video_firmware.install.bin /tmp/video_firmware.install.bin, (1556) [./src/rtk_ui.cpp]

Got encoding system: 7 (PAL)
call initRPCProxy... done.
call getTVE... done.
call prepareCLNT... done.



[Video Firmware Version]   399810
[Video Binary  Built on]   Jan 12 2012 22:38:13
pli malloc order: 12
+++ ALLOC index: 0 order: 12
 zone: 80849000 page: 80849000(82000000) count: 4096
 start remap DVR zone 82000000(80849000) 4096...
total migrated:  done: 0         fail: 0
pli malloc order: 10
+++ ALLOC index: 4096 order: 10
 zone: 80849000 page: 80869000(83000000) count: 1024
 start remap DVR zone 83000000(80869000) 1024...
total migrated:  done: 0         fail: 0
pli malloc order: 10
+++ ALLOC index: 5120 order: 10
 zone: 80849000 page: 80871000(83400000) count: 1024
 start remap DVR zone 83400000(80871000) 1024...
total migrated:  done: 0         fail: 0
pli malloc order: 3
+++ ALLOC index: 6144 order: 3
 zone: 80849000 page: 80879000(83800000) count: 8
 start remap DVR zone 83800000(80879000) 8...
total migrated:  done: 0         fail: 0
pli malloc order: 12
+++ ALLOC index: 8192 order: 12
 zone: 80849000 page: 80889000(84000000) count: 4096
 start remap DVR zone 84000000(80889000) 4096...
total migrated:  done: 0         fail: 0
pli malloc order: 12
+++ ALLOC index: 12288 order: 12
 zone: 80849000 page: 808a9000(85000000) count: 4096
 start remap DVR zone 85000000(808a9000) 4096...
total migrated:  done: 0         fail: 0
pli malloc order: 12
+++ ALLOC index: 16384 order: 12
 zone: 80849000 page: 808c9000(86000000) count: 4096
 start remap DVR zone 86000000(808c9000) 4096...
total migrated:  done: 0         fail: 0
pli malloc order: 12
+++ ALLOC index: 20480 order: 12
 zone: 80849000 page: 808e9000(87000000) count: 4096
 start remap DVR zone 87000000(808e9000) 4096...
total migrated:  done: 0         fail: 0
VBM: configured to SD!
call VIDEVBM: deleting GOB id=0 ...
OVBM: deleting GOB id=1 ...
_VBM: deleting GOB id=2 ...
RVBM: deleting GOB id=3 ...
PVBM: deleting GOB id=4 ...
CVBM: deleting GOB id=5 ...
_VBM: deleting GOB id=6 ...
TVBM: deleting GOB id=7 ...
oVBM: deleting GOB id=8 ...
AVBM: deleting GOB id=9 ...
VBM: deleting GOB id=10 ...
gVBM: deleting GOB id=11 ...
eVBM: deleting GOB id=12 ...
nVBM: deleting GOB id=13 ...
tVBM: deleting GOB id=14 ...
VBM: deleting GOB id=15 ...
_VBM: deleting GOB id=16 ...
VVBM: deleting GOB id=17 ...
iVBM: deleting GOB id=18 ...
dVBM: deleting GOB id=19 ...
eoCreate_0...--- FREE index: 20480 order: 12
 done.
call pl--- FREE index: 16384 order: 12
i_alloBM: configured to HD!
cContinuousMemory... done.
call pli_IPCWriteULONG... done.
call prepareCLNT... done.
call setDebugFlag... done.
call VIDEO_RPC_ToAgent_VideoChunkConfig_0... done.
-=- create MBF engine for //uEGBK.mbf
get_os
(TVE) TVE_DAC_mode 0!! ~~comp 0, ch2 0, mode_3D 0!!
~~TVE standard#
d_language(0)
call SetVO() start.
[RPCTest] VIDEO_RPC_VOUT_ToAgent_SetVideoStandard
[RPCTest] VIDEO_RPC_VOUT_ToAgent_SetVideoStandard = S_OK
vo.SetBackground()
vo.ConfigureOSD()
vo.SetDeintMode()
vo.SetRescaleMode()
vo.ConfigureDisplayWindow()
vo.ConfigGraphicCanvas()
call SetVO() end.
call SetHDMI() start.
[HDMI]: Turn off HDMI
[HDMI]: Set AVMute
[HDMI]: TURN OFF HDMI PHY for Jupiter/Saturn
-----------------------------------------
[I2C0] Xfer fail - TXABORT (1/2), Reason=0001
msg->addr  = 50
msg->flags = 0001
msg->len   = 4
msg->buf   = 98395c00
-----------------------------------------
[HDMI]:
(VO_ConfigHDMI_InfoFrame) L:219, is_hdmi_plugin 1, hdmiMode 1!!
(HDMI_3D) mode 1, HDMI_gen 0, En_3D 0, Format_3D 0!!
 go back SET_HDMI!! Read Epli malloc order: 12
DI+++ ALLOC index: 16384 order: 12
D  zone: 80849000 page: 808c9000(86000000) count: 4096
fa start remap DVR zone 86000000(808c9000) 4096...
nls, total migrated:    A dIon[e::TVE 0-         dfafilw:  0
  313
WARNING[3]:TVE p-underflow @ line 1
WARNING[3]:TVE h-underflow @ line 1
i=0
[HDMI]: Turn on HDMI mode...................
[RPCTest] VIDEO_RPC_VOUT_ToAgent_ConfigHdmiInfoFrame_0 = S_OK
[HDMI]: Turn on HDMI
[HDMI]: Clear AVMute
[HDMI]: TURN ON HDMI PHY for Jupiter/Saturn
call SetHDMI() end.
call EnableUI()
DG_CreateSurface()
DG_GetDisplayHandle()
DG_DisplayArea() start.
DG_DisplayArea() end.
call EnableUI() end.
---------- g_totalSize(199725)KB

Extract bootloader.tar file...
tarfile_offset:0x00aa4400 (2457600 Bytes = 2400 KB)
extract bootloader.tar from /mnt/usbmounts/sda1/install.img
100 |******************************| 2400 KB

total_time:0 secands
extract ok
command:mkdir -p /tmp/tar_file_tmp;tar -xf /tmp/bootfw -C /tmp/tar_file_tmp, (55) [./src/rtk_burn.cpp]
/tmp/tar_file_tmp/logo10.bin not exist.
/tmp/tar_file_tmp/logo11.bin not exist.
/tmp/tar_file_tmp/logo12.bin not exist.
/tmp/tar_file_tmp/logo13.bin not exist.
/tmp/tar_file_tmp/logo14.bin not exist.
/tmp/tar_file_tmp/logo15.bin not exist.
/tmp/tar_file_tmp/logo16.bin not exist.
/tmp/tar_file_tmp/logo17.bin not exist.
/tmp/tar_file_tmp/logo18.bin not exist.
/tmp/tar_file_tmp/logo19.bin not exist.
/tmp/tar_file_tmp/logo20.bin not exist.
flapli malloc order: 9
sh+++ ALLOC index: 6656 order: 9
 t zone: 80849000 page: 8087d000(83a00000) count: 512
yp start remap DVR zone 83a00000(8087d000) 512...
e: nand
total migrated:  done: 512       fail: 0
pli malloc order: 4
+++ ALLOC index: 6160 order: 4
 zone: 80849000 page: 80879200(83810000) count: 16
 start remap DVR zone 83810000(80879200) 16...
total migrated:  done: 16        fail: 0
pli malloc order: 7
+++ ALLOC index: 6272 order: 7
 zone: 80849000 page: 8087a000(83880000) count: 128
 start remap DVR zone 83880000(8087a000) 128...
total migrated:  done: 128       fail: 0
pli malloc order: 10
+++ ALLOC index: 7168 order: 10
 zone: 80849000 page: 80881000(83c00000) count: 1024
 start remap DVR zone 83c00000(80881000) 1024...
total migrated:  done: 1024      fail: 0
Begin:[H27UBG8T2B][20202020 20 20]
[20202020 20 20]
[20202020 20 20]
blk_state_len =0x19
get original param in block b, size 0x520
............/...............--- FREE index: 6656 order: 9
..--- FREE index: 6160 order: 4
....--- FREE index: 7168 order: 10
..--- FREE index: 6272 order: 7
................../............................................................................................................................................................................................................................................................././........................................./............................................................................................................................................................................................................................................................././........................................./............................................................................................................................................................................................................................................................././........................................./.............................................................................................................................................................................................................................................................do_exit_n
blk_state:
d0 bb bb 23 23 23 23 79 79 79 79 80 80 80 80 81
ff ff ff ff ff ff ff ff ff
Finish
write bootcode success
[INSTALL LOG][./src/rtk_burn.cpp][58]
boot_main:ret:0
[INSTALL LOG][./src/rtk_main.cpp][44]
In NAND FLASH
command:echo -n RESCUE__ | dd of=/dev/mtdblock0 bs=1 seek=56623104, (103) [./src/rtk_burn.cpp]
.8+0 records in
8+0 records out

Extract mkyaffs2image file...
tarfile_offset:0x00365e00 (48052 Bytes = 46 KB)
extract mkyaffs2image from /mnt/usbmounts/sda1/install.img
100 |******************************| 46 KB

total_time:0 secands
extract ok

Extract nandwrite file...
tarfile_offset:0x00371c00 (61668 Bytes = 60 KB)
extract nandwrite from /mnt/usbmounts/sda1/install.img
100 |******************************| 60 KB

total_time:0 secands
extract ok

Extract flash_erase file...
tarfile_offset:0x00023e00 (47504 Bytes = 46 KB)
extract flash_erase from /mnt/usbmounts/sda1/install.img
100 |******************************| 46 KB

total_time:0 secands
extract ok
command:chmod 777 /usr/sbin/mkyaffs2image;chmod 777 /usr/sbin/nandwrite;chmod 777 /usr/sbin/flash_erase, (202) [./src/rtk_burn.cpp]

Burning Kernel efwtype(0) image with mem_offset(0x80100000)  ...
flash_offset:0x0003800000 flash_allo_size:0x00800000 bytes(4 sector)
tarfile_offset:0x00381200      image_size:0x00722f44 bytes(7307 KB)
command:/usr/sbin/flash_erase /dev/mtd0 58720256 4, (572) [./src/rtk_burn.cpp]
Erase Total 4 Units
Performing Flash Erase of length 2097152 at offset 0x3e00000 done
popen(cmd):/usr/sbin/nandwrite -c -x -X -s 58720256 -l 7483204 /dev/mtd0 -
start burning
progress_callback---------- totalLen(7483204) g_burnSize(0)
nandwrite $ Revision: 1.63 release Version.$
struct64...
Linux version 0x2060c
....checksum:0x215994C5

total_time:2 secands
Writing data finishes !!
Complete!!


Burning Audio kernel efwtype(1) image with mem_offset(0x81b00000)  ...
flash_offset:0x0004000000 flash_allo_size:0x00200000 bytes(1 sector)
tarfile_offset:0x0c882e00      image_size:0x001cbc30 bytes(1839 KB)
command:/usr/sbin/flash_erase /dev/mtd0 67108864 1, (572) [./src/rtk_burn.cpp]
Erase Total 1 Units
Performing Flash Erase of length 2097152 at offset 0x4000000 done
popen(cmd):/usr/sbin/nandwrite -c -x -X -s 67108864 -l 1883184 /dev/mtd0 -
start burning
progress_callback---------- totalLen(1883184) g_burnSize(7483204)
nandwrite $ Revision: 1.63 release Version.$
struct64...
Linux version 0x2060c
.checksum:0x0877547B

total_time:1 secands
Writing data finishes !!
Complete!!


Burning Video kernel efwtype(2) image with mem_offset(0x81d80000)  ...
flash_offset:0x0004200000 flash_allo_size:0x00400000 bytes(2 sector)
tarfile_offset:0x00e66000      image_size:0x0023f8c0 bytes(2302 KB)
command:/usr/sbin/flash_erase /dev/mtd0 69206016 2, (572) [./src/rtk_burn.cpp]
Erase Total 2 Units
Performing Flash Erase of length 2097152 at offset 0x4400000 done
popen(cmd):/usr/sbin/nandwrite -c -x -X -s 69206016 -l 2357440 /dev/mtd0 -
start burning
progress_callback---------- totalLen(2357440) g_burnSize(9366388)
nandwrite $ Revision: 1.63 release Version.$
struct64...
Linux version 0x2060c
..checksum:0x07165C5A

total_time:1 secands
Writing data finishes !!
Complete!!


Burning Audio Bootfile efwtype(3) image with mem_offset(0xffffffff)  ...
flash_offset:0x0004600000 flash_allo_size:0x00000000 bytes(0 sector)
tarfile_offset:0x00000000      image_size:0x00000000 bytes(0 KB)
[INSTALL DEBUG][./src/rtk_burn.cpp][562]
Audio Bootfile don't exist
[INSTALL DEBUG][./src/rtk_main.cpp][78]
Audio bootfile none

Burning Video Bootfile efwtype(4) image with mem_offset(0xffffffff)  ...
flash_offset:0x0004600000 flash_allo_size:0x00000000 bytes(0 sector)
tarfile_offset:0x00000000      image_size:0x00000000 bytes(0 KB)
[INSTALL DEBUG][./src/rtk_burn.cpp][562]
Video Bootfile don't exist
[INSTALL DEBUG][./src/rtk_main.cpp][83]
Video bootfile none

Burning RootFS efwtype(5) image with mem_offset(0x00000000)  ...
flash_offset:0x00a4600000 flash_allo_size:0x0b800000 bytes(92 sector)
tarfile_offset:0x010a5c00      image_size:0x0b7dd000 bytes(188276 KB)
command:/usr/sbin/flash_erase /dev/mtd0 2757754880 92, (572) [./src/rtk_burn.cpp]
Erase Total 92 Units
Performing Flash Erase of length 2097152 at offset 0xafc00000 done
popen(cmd):/usr/sbin/nandwrite -c -x -X -s 2757754880 -l 192794624 /dev/mtd0 -
start burning
progress_callback---------- totalLen(192794624) g_burnSize(11723828)
nandwrite $ Revision: 1.63 release Version.$
struct64...
Linux version 0x2060c
..............................................
..............................................................checksum:0xE61C5466

total_time:66 secands
Writing data finishes !!
Complete!!


Burning Resource efwtype(6) image with mem_offset(0x00000000)  ...
flash_offset:0x00afe00000 flash_allo_size:0x00000000 bytes(0 sector)
tarfile_offset:0x00000000      image_size:0x00000000 bytes(0 KB)
[INSTALL DEBUG][./src/rtk_burn.cpp][562]
Resource don't exist
[INSTALL DEBUG][./src/rtk_main.cpp][94]
burn Resource fail

Burning Preserve efwtype(7) image with mem_offset(0x00000000)  ...
flash_offset:0x00afe00000 flash_allo_size:0x03200000 bytes(25 sector)
tarfile_offset:0x00000000      image_size:0x00000000 bytes(0 KB)
command:/usr/sbin/flash_erase /dev/mtd0 2950692864 25, (491) [./src/rtk_burn.cpp]
Erase Total 25 Units
Performing Flash Erase of length 2097152 at offset 0xb2e00000 done
preserve partition Complete!!


Burning Usr.local.etc efwtype(8) image with mem_offset(0x00000000)  ...
flash_offset:0x00b3000000 flash_allo_size:0x40000000 bytes(512 sector)
tarfile_offset:0x00cfc600      image_size:0x00169740 bytes(1445 KB)

Burning Usr.local.etc efwtype(8) image with mem_offset(0x00000000)  ...
flash_offset:0x00b3000000 flash_allo_size:0x40000000 bytes(512 sector)
tarfile_offset:0x00cfc600      image_size:0x00169740 bytes(1445 KB)
command:/usr/sbin/flash_erase /dev/mtd0 3003121664 512, (572) [./src/rtk_burn.cpp]
Erase Total 512 Units
Performing Flash Erase of length 2097152 at offset 0xf2e00000 done
popen(cmd):/usr/sbin/nandwrite -c -y -n -o -X -s 3003121664 -l 1480512 /dev/mtd0 -
start burning

0 |                              | 8 KBnandwrite $ Revision: 1.63 release Version.$
struct64...
Linux version 0x2060c
100 |******************************| 1445 KB
checksum:0x05C4FD60

total_time:1 secands
Data buf File I/O error on input file: Unknown error 0
ERR readlen is 8192, cnt is 3072
Complete!!

[INSTALL INFO][./src/rtk_burn.cpp][1010]          RootFS offset(0xa4600000)
[INSTALL INFO][./src/rtk_burn.cpp][1041]        Preserve offset(0xafe00000)
[INSTALL INFO][./src/rtk_burn.cpp][1054]   Usr.local.etc offset(0xb3000000)
[INSTALL INFO][./src/rtk_burn.cpp][1066]       remapping offset(0xf3000000)
[INSTALL INFO][./src/rtk_burn.cpp][1099] partition(0) length(0xa4600000)
[INSTALL LOG][./src/rtk_burn.cpp][1128]
BOOTTABLE PRESERVE[INSTALL INFO][./src/rtk_burn.cpp][1158] rtk_fw_head.part_count:5
[INSTALL LOG][./src/rtk_fwdesc.cpp][351]
veraion:0x01 fw_count:7, part_count:5
checksum:0x00001efc
[INSTA.L INFO][./src/rtk_mtd.cpp][101] Open MTD_BLOCK /dev/mtdblock0 with 56623104(0x3600000) offset
56 45 52 4f 4e 41 5f 5f 00 00 1e fc 01 00 00 00
00 00 00 00 00 20 00 00 00 00 00 f0 00 00 00 e0

01 80 a4 60 00 00 03 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02 00 0b 80 00 00 01 06 00 00 00 00 00 00 00 00
2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02 00 03 20 00 00 01 09 00 00 00 00 00 00 00 00
63 61 63 68 65 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02 00 40 00 00 00 01 09 00 00 00 00 00 00 00 00
2f 75 73 72 2f 6c 6f 63 61 6c 2f 65 74 63 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01 80 0d 00 00 00 01 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02 80 00 00 00 00 80 10 00 00 03 80 00 00 00 72
2f 44 00 80 00 00 00 00 00 00 00 00 00 00 00 00

03 80 00 00 00 00 81 b0 00 00 04 00 00 00 00 1c
bc 30 00 20 00 00 00 00 00 00 00 00 00 00 00 00

04 80 00 00 00 00 81 d8 00 00 04 20 00 00 00 23
f8 c0 00 40 00 00 00 00 00 00 00 00 00 00 00 00

06 80 00 00 00 00 00 00 00 00 a4 60 00 00 0b 7d
d0 00 0b 80 00 00 00 00 00 00 00 00 00 00 00 00

09 00 00 00 00 00 00 00 00 00 af e0 00 00 00 00
00 00 03 20 00 00 00 00 00 00 00 00 00 00 00 00

09 00 00 00 00 00 00 00 00 00 b3 00 00 00 00 16
97 40 40 00 00 00 00 00 00 00 00 00 00 00 00 00

00 80 00 00 00 00 00 00 00 00 f3 00 00 00 0d 00
00 00 0d 00 00 00 00 00 00 00 00 00 00 00 00 00

..

rtk_burn_rtkimg_from_usb():0

install time:92 secands
command:pci stop, (138) [install_a.cpp]
sh: pci: not found
[INSTALL DEBUG][./src/rtk_common.cpp][190]
Can't exec command:pci stop, (138) [install_a.cpp]
command:reboot, (139) [install_a.cpp]
The system is going down NOW!
Sending SIGTERM to all processes
clear pli setting....
se release, count = 0
Sending SIGKILL to all processes
Requesting system reboot
#######[cfyeh-debug] hub_events(3615) usb_plug_status 1
usb 1-1: USB disconnect, address 2
#######[cfyeh-debug] usb_stor_disconnect(1021) usb_plug_status 2
#@#[cfyeh-debug] sd_remove(2385) sd_flag 1
#@#[cfyeh-debug] sd_remove(2403) sd_flag 0
#######[cfyeh-debug] usb_stor_disconnect(1025) usb_plug_status 1
testclear_lockdata_once open lock file error.
Hotplug: umount -f -l /tmp/usbmounts/sda1       ret: 0
Hotplug: Umount sda1 successfully.
Restarting system.
#######[cfyeh-debug] hub_events(3619) usb_plug_status 0



Буду пробывать проверку на BB сектора.
Densys
 
Posts: 5
Joined: 23 Jul 2020, 00:44

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 24 Jul 2020, 16:59

где логи с темы: (они на флешке создадустся в процессе лечения)

Универсальный бут для RTD1186 и скрипты
те нужно пройти квест сброса битых блоков 0+1 (скачать файлы из этих пунктов и строго по инструкции)
там будет полное стирание NAND вместе с бутом! и пересоздание BBT
реска те нужна была ток для входа в восстановление, но у тя битый бут и битая нанд
пока 27 блок бит -
[dump_BBT] Nand BBT Content
[0] (0, 27, 0, 2047)

ни одна прошивка не взлетит.

PS
Linux version 2.6.34-VENUS (william@rtdmpsa-05) (gcc version 4.3.6 20110218 (prerelease) (GCC) ) #21 PREEMPT Wed Dec 4 13:08:14 CST 2013
...
Bootloader version: KIIE.0402.1067. This version string is of new format.

это не мой бут! - ты не проходил процедуру сброса.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Densys » 29 Jul 2020, 14:35

квест сброса битых блоков 0+1 прошел.
потом прошился нормальной прошивкой.
Все работает.
Densys
 
Posts: 5
Joined: 23 Jul 2020, 00:44

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Gena_cross » 01 Mar 2021, 18:25

помогите советом, заменил в XDS73D Nand и теперь пишет NOR, как восстановить загрузчик?
Iconbit XDS73D - inext_hd1_225_r0
User avatar
Gena_cross
 
Posts: 4
Joined: 04 Nov 2017, 22:08
Location: Ангарск

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 02 Mar 2021, 21:45

просто скормить прошивку с бутом!
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby sghari » 30 Apr 2021, 14:18

Здравствуйте, я не слишком разбираюсь в прошивках, но хотелось бы восстановить мой XDS1003DW, который после пяти лет исправной работы вдруг начал выбрасывать NUPGRADE и стрелку на выход. Может кто-то захочет починить мой плеер за плату? Я живу в Москве. Жду предложений. Могу выслать почтой CDEK.
Iconbit XDS1003DW
1075C3A00546
sghari
 
Posts: 1
Joined: 30 Apr 2021, 13:59

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Gena_cross » 16 Apr 2022, 18:10

Подскажите пожалуйста как подключить Ttl к Iconbit XDS73d? К каким контактам, нет в терминале сигнала
Iconbit XDS73D - inext_hd1_225_r0
User avatar
Gena_cross
 
Posts: 4
Joined: 04 Nov 2017, 22:08
Location: Ангарск

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 17 Apr 2022, 10:50

там стандартный разьем mele у самого проца, 4 пин....
с одного края 3,3в оно нам не нужно
а с другого gnd tx rx , земля с краю а tx отличить от rx легко, достаточно rx адаптера подключить на один из двух пинов и включить плеер, там где пойдет лог - значит оно.
Снимок экрана от 2022-04-17 11-51-07.png
Снимок экрана от 2022-04-17 11-51-07.png (327.16 KiB) Viewed 9316 times
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Gena_cross » 19 Apr 2022, 10:32

после заливки в 25L1606 прошивки на экране флэшка , могу приложить лог файл, как быть дальше?
Attachments
Log.rtf
(16.27 KiB) Downloaded 148 times
Iconbit XDS73D - inext_hd1_225_r0
User avatar
Gena_cross
 
Posts: 4
Joined: 04 Nov 2017, 22:08
Location: Ангарск

Re: Восстановление при самой неудачной прошивке Saturn(1186)

Postby Virtual » 19 Apr 2022, 17:45

на экране флэшка это NOR бут сообщает что дай флешку с NAND бут кодом., но!
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
READ ID:0x20 0x20 0x20 0x20 0x20 0x20
Warning: Lookup Table do not have this nand flash !!
rtk_nand: Manufacture ID=0x20, Chip ID=0x20, 3thID=0x20, 4thID=0x20, 5thID=0x20, 6thID=0x20

Warning я не знаю таких флешек!!
ID:0x20 0x20 0x20 0x20 0x20 0x20 - таких флешек не бывает! тоесть или чип не читается или ему писец, но 8-) мы уже встречали такое, много раз это было просто кривой бут, и многим помогло установка моего.
ставь мой NORBoot60 из шапки темы. после чего в логах NAND чип должен начать опознаватся.... ну уж после этого корми прошивку с NAND бут кодом.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 15 guests