Восстановление при самой неудачной прошивке Mars(1073/1283)

о железе плеера и о периферии

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 03 Jan 2020, 16:45

больше похоже что или RAM не пашет или с ошибками вливается. CRC не сходится
1073-l.PNG
1073-l.PNG (6.69 KiB) Viewed 6735 times

PS кст в пр. раз с таким-же плеером как то умудрились повредить дорожки к чипу RAM
u_ps.PNG
u_ps.PNG (348.17 KiB) Viewed 6733 times


PSPS
Похоже не видит он NAND

до этого даже не доходит, бинарник прошивальщика бута даже не запускается.
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby kliaoz » 29 Nov 2022, 22:11

Здравствуйте.Есть девайс Konoos GV-3765 (RTD1073DD).Стояла там заводская прошивка.Решил перепрошить ,т.к. USB мёртво на нём подцепил по SATA ноутбучный винт с прошивкой amp_r13_vrtn_42 .По кнопке power не прошивался ну и сдуру через меню в плеере нажал обновить.Девайс перезагрузился и застрял на логотипе.Всё ...приехали.
Разобрал ,подключил консольный кабель к UART но erase -m и erase -e не помогают .Хотел бы спросить совета как дальше быть ?
| +
IMG20221129194615.jpg
фото платы
IMG20221129194615.jpg (5.79 MiB) Viewed 3246 times


putty.log
| +
?hеllo wпrld!
Љ528°µ w28a° iwatйA[HDMI]: Set I2C Speed = 100 kHz

[HDMI]: Chk_HotPlug() TV is not connected.

[HDMI]: Read_EDID abort, HDMI cable plug off.

[HDMI]: TV is not connected.

PAL logo


REALTEK ROM Monitor, Revision noon.0202.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Nov 9 2010 11:27:40 /noon.0202.0026

MAC address = 00.11.22.c4.3d.61

Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision = 0x93 / 0x78

Endianness = Little
Flash memory size = 256 MByte

SDRAM size = 128 MByte

First free SDRAM address = 0x800fab00


Press 'ESC' to Monitor mode

Signature(яяяяяяяя) error! Entering rescue linux...

Rescue kernel in FLASH, total size = 0xf6413



seg.1 addr 0xa0a056f8, size = 0xf6413



seg.2 addr 0x0, size = 0x0

copy rescue0: from a0a056f8 to 81000000, len = f6413

decompressing rescue: from 81000000 to 80100000: size = f6413

lzma finished

decompressing rescue done

go 0x80100000

Reset Ethernet Mac.




Address = 0x80100000


Realtek LINUX (DC ALIAS) started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 1 UART.
System CPU uses external timer interrupt.
Bootloader version: noon.0202.0026. This version string is of new format.
Error! Unknown SB2_CHIP_INFO. Linux is too old?
Ethernet Mac address: 00.11.22.C4.3D.61
Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (alan@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.01-20051114) #43 Tue Apr 27 15:39:36 CST 2010

**************************************************************

You didn't specify audio image address, use default instead...

**************************************************************

audio addr: 0

CPU revision is: 00019378

Determined physical RAM map:

memory: 00100000 @ 00000000 (usable)

memory: 002bc000 @ 00100000 (reserved)

memory: 019c4000 @ 003bc000 (usable)

memory: 00280000 @ 01d80000 (reserved)

memory: 06000000 @ 02000000 (usable)

show info: max_low_pfn:32768

show info: min_low_pfn:956

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Estimate value: CPU frequency 405.02 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 123532k/125712k available (1981k kernel code, 2112k reserved, 302k data, 436k init, 0k highmem)

Warning! Unknown board id.

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction... available.

Linux NoNET1.0 for Linux 2.6

SCSI subsystem initialized

usbcore: registered new driver hub

se init module major number = 254

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

Hello, Realtek TLB Mapper

AllocBP size: 294912 order: 7

<<<DVR FREE AREA>>>

0: 0

1: 0

2: 0

3: 0

4: 0

5: 0

6: 0

7: 0

8: 0

9: 0

10: 0

11: 0

12: 6

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x0

NTFS driver 2.1.28 [Flags: R/O].

Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

Mars no support IDE

ide generic info: ide_generic_init

Mars no support IDE

libata version 1.12 loaded.

sata driver initial...2009/12/30 14:50

mars_init_sata(1255)dev_addr:80336178

ata_device_add(4891)probe begin

scsi0 : SATA_DRV

sata dma reset

sata1: reset phy again!

sata phy reset

sata1: reset phy again!

sata phy reset

sata1: reset phy extra!

sata phy reset

sata1: reset phy extra!

sata phy reset

sata1: reset phy extra!

sata phy reset

sata1: phy reset timeout!

sata1: no device found (phy stat 00000000)

sata1: ata_bus_probe failed

scsi1 : SATA_DRV

sata dma reset

sata2: reset phy again!

sata phy reset

sata2: reset phy again!

sata phy reset

sata2: phy reset timeout!

sata2: no device found (phy stat 00000000)

sata2: ata_bus_probe failed

VenusSFC MTD init

serial flash inaccessible

physmap flash device: 10000000 at fd00000

Realtek NAND Flash Driver Rev:305341 (2010-04-13)

One HY27UF082G2B chip has 1 die(s) on board

nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

[0] (0, 1343, 0, 2047)

[1] (0, 1424, 0, 2046)

RTK: using the whole nand as a partitoin

Realtek Nand Flash Driver is successfully installing.

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[cfyeh] set PPE = 0

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

Initializing USB Mass Storage driver...

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

Setting registers , Enable OTG

dwc_otg: version 2.60a 22-NOV-2006

DWC_otg: Shared Tx FIFO mode

i2c /dev entries driver

[I2C0] i2c speed changed to 100 KHz

I2C0 Bus Status Check.... OK

=========================

= VER : 2.0a

=========================

DWC_otg: USB RESET

= PHY : 0

= MODE: MARS

= SPD : 100

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 8

= RX FIFO DEPTH : 8

= FIFO THRESHOLD: 4

= BUS JAM RECORVER : ON

= NON STOP WRITE : OFF

= SP PROTECT : ON

=========================

FATAL : I2C 1 pins have been occupied by PCI

Trying to free free IRQ3

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 436k freed


init started: BusyBox v1.1.3 (2010.04.27-07:38+0000) multi-call binary

Starting pid 334, console /dev/console: '/etc/init.d/rcS'
120+0 records in
120+0 records out
Welcome to Realtek Rescue Linux for PhotoViewer
mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: Unknown error 19
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2

>>>>>> loader start! (Apr 27 2010:15:39:10, version=00.01.01)
Secure Boot is off.

Please press Enter to activate this console. Hotplug: device "ram0" is skipped.
Hotplug: device "loop0" is skipped.
Hotplug: device "loop1" is skipped.
Hotplug: device "loop2" is skipped.
Hotplug: device "loop3" is skipped.
Hotplug: device "loop4" is skipped.
Hotplug: device "loop5" is skipped.
Hotplug: device "loop6" is skipped.
Hotplug: device "loop7" is skipped.
Hotplug: device "mtdblock0" is skipped.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.


Starting pid 364, console /dev/console: '/bin/sh'


BusyBox v1.1.3 (2010.04.27-07:38+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# Secure Boot is off.
heSecure Boot is off.
lp

Built-in commands:
-------------------
. : break cd chdir continue eval exec exit export false hash
help local pwd read readonly return set shift times trap true
type ulimit umask unset wait

# Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.

#
# Secure Boot is off.
buSecure Boot is off.
sybSecure Boot is off.
ox
BusyBox v1.1.3 (2010.04.27-07:38+0000) multi-call binary

Usage: busybox [function] [arguments]...
or: [function] [arguments]...

BusyBox is a multi-call binary that combines many common Unix
utilities into a single executable. Most people will create a
link to busybox for each function they wish to use and BusyBox
will act like whatever it was invoked as!

Currently defined functions:
[, [[, ash, busybox, chmod, cp, cut, dd, echo, grep, halt, init,
insmod, ln, ls, lsmod, lzmacat, mkdir, mknod, modprobe, mount,
mv, poweroff, reboot, rm, rmdir, rmmod, sh, sleep, swapoff, swapon,
sync, tar, test, touch, umount, unlzma, unzip

# Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.


С зажимаеием Esc
| +
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2006.05.02 00:20:11 =~=~=~=~=~=~=~=~=~=~=~=
Ддддддддддддддддджджжджжджжжжжжжджджжджжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжджжж
їhelмo worмd!
5І805 wІ8a0 iwбtiA~AюA~A~A~A~A~Б~A~Б~Б~AюA~AюAюA~A~A~A~Б~A~A~Б~AюA~AюAюA~A~A~A~Б~A~A~Б~AюA~A~AюA~A~A~A~Б~Б~A~Б~A
[HDMI]: Set I2C Speed = 100 kHz

[HDMI]: Chk_HotPlug() TV is not connected.

[HDMI]: Read_EDID abort, HDMI cable plug off.

[HDMI]: TV is not connected.

PAL logo


REALTEK ROM Monitor, Revision noon.0202.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Nov 9 2010 11:27:40 /noon.0202.0026

MAC address = 00.11.22.c4.3d.61

Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision = 0x93 / 0x78

Endianness = Little
Flash memory size = 256 MByte

SDRAM size = 128 MByte

First free SDRAM address = 0x800fab00


Press 'ESC' to Monitor mode

Realtek> elp

Error : Command not found : elp

Realtek> help

Available commands :

. . (repeat last command line)
; ; (command separator)
+ + <repeat count> ;
compare compare <address1> <address2> <size>
continue continue
copy copy [-f] <src> <dst> <size>
disk disk [-f] (id [hda|hdb|hdc|hdd] ) |
(read hda|hdb|hdc|hdd <sector> <count> <addr> ) |
(write hda|hdb|hdc|hdd <sector> <count> <addr> )
dump dump [-m][-8|-16|-32] <address> [<size>]
erase erase -e|-m| <address> <size>
fill fill [-8|-16|-32] <address> <size> <data>
fread fread tftp://<ipaddr>/<filename> <address>
fwrite fwrite tftp://<ipaddr>/<filename> <address> <size>
go go [?|.|<address> [<args>]]
help help [<command>]
info info [boot|board|cpu|sysctrl|memory|uart|all|pll]
load load [-r]
([tftp:][//<ipaddr>][/<filename>]) |
Press any key (Ctrl-C to break, Enter to singlestep)
Stopped due to Ctrl-C

Realtek> info

REALTEK ROM Monitor, Revision noon.0202.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Nov 9 2010 11:27:40 /noon.0202.0026

MAC address = 00.11.22.c4.3d.61

Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision = 0x93 / 0x78

Endianness = Little
Flash memory size = 256 MByte

SDRAM size = 128 MByte

First free SDRAM address = 0x800fab00
Konos GV3765,Iconbit XDS1003D,Ugoos X3Pro,Vontar x3,Tanix W2
User avatar
kliaoz
 
Posts: 5
Joined: 29 Nov 2022, 02:15

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 30 Nov 2022, 05:28

да USB мертв точнее не сам USB а 99% хаб (при желании можно его отпаять и получить хотя-б один прямой USB)
второй USB занят USB-B (так же можно поменять разьем на тип А и задействовать)

по логу rescue вполне себе рабочее.... только в логе нет подключеного SATA диска
PS подкинь диск по SATA и сними лог (можеш заранее на диске создать маленький раздел типа FAT :twisted: )
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby kliaoz » 30 Nov 2022, 10:33

"Virtual"
вот лог с подключеным HDD
| +
жжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжжж
?иello  worldЎЌ
5285°2 80w чaaiitA[HDMI]: Set I2C Speed = 100 kHz[HDMI]: Chk_HotPlug() TV is not connected.
[HDMI]: Read_EDID abort, HDMI cable plug off.[HDMI]: TV is not connected.PAL logo
REALTEK ROM Monitor, Revision noon.0202.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=Nov 9 2010 11:27:40 /noon.0202.0026
MAC address =00.11.22.c4.3d.61
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00Processor ID/revision = 0x93 / 0x78Endianness = Little
Flash memory size = 256 MByteSDRAM size = 128 MByte
First free SDRAM address = 0x800fab00
Press 'ESC' to Monitor mode
Signature(яяяяяяяя) error! Entering rescue linux...Rescue kernel in FLASH, total size = 0xf6413
seg.1 addr 0xa0a056f8, size = 0xf6413 seg.2 addr 0x0, size = 0x0copy rescue0:
from a0a056f8 to 81000000, len = f6413decompressing rescue: from 81000000 to 80100000:
size = f6413lzma finished decompressing rescue donego 0x80100000 Reset Ethernet Mac.
Address = 0x80100000
Realtek LINUX (DC ALIAS) started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 1 UART.
System CPU uses external timer interrupt.
Bootloader version: noon.0202.0026. This version string is of new format.
Error! Unknown SB2_CHIP_INFO. Linux is too old?
Ethernet Mac address: 00.11.22.C4.3D.61
Model Config length=0
Base year of RTC is 2010.
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (alan@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.01-20051114) #43 Tue Apr 27 15:39:36 CST 2010

**************************************************************

You didn't specify audio image address, use default instead...

**************************************************************

audio addr: 0

CPU revision is: 00019378

Determined physical RAM map:

memory: 00100000 @ 00000000 (usable)

memory: 002bc000 @ 00100000 (reserved)

memory: 019c4000 @ 003bc000 (usable)

memory: 00280000 @ 01d80000 (reserved)

memory: 06000000 @ 02000000 (usable)

show info: max_low_pfn:32768

show info: min_low_pfn:956

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

PID hash table entries: 256 (order: 8, 4096 bytes)

Estimate value: CPU frequency 405.02 MHz

Using 27.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 123532k/125712k available (1981k kernel code, 2112k reserved, 302k data, 436k init, 0k highmem)

Warning! Unknown board id.

Warning! Unknown board id.

==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================

Mount-cache hash table entries: 512

Checking for 'wait' instruction... available.

Linux NoNET1.0 for Linux 2.6

SCSI subsystem initialized

usbcore: registered new driver hub

se init module major number = 254

size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...

Hello, Realtek TLB Mapper

AllocBP size: 294912 order: 7

<<<DVR FREE AREA>>>

0: 0

1: 0

2: 0

3: 0

4: 0

5: 0

6: 0

7: 0

8: 0

9: 0

10: 0

11: 0

12: 6

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x0

NTFS driver 2.1.28 [Flags: R/O].

Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize

loop: loaded (max 8 devices)

Mars no support IDE

ide generic info: ide_generic_init

Mars no support IDE

libata version 1.12 loaded.

sata driver initial...2009/12/30 14:50

mars_init_sata(1255)dev_addr:80336178

ata_device_add(4891)probe begin

scsi0 : SATA_DRV

sata dma reset

sata1: occupy port0, COMRESET ok, sstatus = 113, SCRstatus = 113

__mars_sata_phy_reset(925)check taskfile state

ata_dev_identify(1477)do ATA identify

sata1: dev 0 ATA, max UDMA/100, 1465149168 sectors: lba48

Vendor: ATA Model: TOSHIBA MQ01ABD0 Rev: AX00

Type: Direct-Access ANSI SCSI revision: 05

scsi1 : SATA_DRV

sata dma reset

modprobe: module sd_mod not found.
modprobe: failed to load module sd_mod
sata2: reset phy again!

sata phy reset

sata2: reset phy again!

sata phy reset

sata2: phy reset timeout!

sata2: no device found (phy stat 00000000)

sata2: ata_bus_probe failed

SCSI device sda: 1465149168 512-byte hdwr sectors (750156 MB)

SCSI device sda: drive cache: write back

SCSI device sda: 1465149168 512-byte hdwr sectors (750156 MB)

SCSI device sda: drive cache: write back

/dev/scsi/host0/bus0/target0/lun0: p1

data[0] 0x0 signature[0] 0xbabeface

data[1] 0x0 signature[1] 0xdeadbeef

Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0

VenusSFC MTD init

serial flash inaccessible

physmap flash device: 10000000 at fd00000

Realtek NAND Flash Driver Rev:305341 (2010-04-13)

One HY27UF082G2B chip has 1 die(s) on board

nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0

[rtk_nand_scan_bbt] have created bbt B0, just loads it !!

[dump_BBT] Nand BBT Content

[0] (0, 1343, 0, 2047)

[1] (0, 1424, 0, 2046)

RTK: using the whole nand as a partitoin

Realtek Nand Flash Driver is successfully installing.

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ehci_hcd ehci_hcd: EHCI Host Controller

ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1

ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000

ehci_hcd ehci_hcd: park 0

ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

hub : individual port power switching

hub : individual port over-current protection

[cfyeh] set PPE = 0

[usb_param] setting for mars

Setting for MARS-B

[usb_param] set port two for host!

[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit

[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit

[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit

[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit

[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit

ohci_hcd ohci_hcd: OHCI Host Controller

ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2

ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

hub : no power switching (usb 1.0)

hub : no over-current protection

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

Initializing USB Mass Storage driver...

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

ehci_hcd ehci_hcd: port 1 reset error -145

hub 1-0:1.0: hub_port_status failed (err = -32)

hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

Setting registers , Enable OTG

dwc_otg: version 2.60a 22-NOV-2006

DWC_otg: Shared Tx FIFO mode

i2c /dev entries driver

[I2C0] i2c speed changed to 100 KHz

I2C0 Bus Status Check.... OK

=========================

= VER : 2.0a

=========================

DWC_otg: USB RESET

= PHY : 0

= MODE: MARS

= SPD : 100

= SAR : 0x024 (7 bits)

= TX FIFO DEPTH : 8

= RX FIFO DEPTH : 8

= FIFO THRESHOLD: 4

= BUS JAM RECORVER : ON

= NON STOP WRITE : OFF

= SP PROTECT : ON

=========================

FATAL : I2C 1 pins have been occupied by PCI

Trying to free free IRQ3

Freeing prom memory: 0kb freed

Reclaim bootloader memory from 80020000 to 80100000

Freeing unused kernel memory: 436k freed


init started: BusyBox v1.1.3 (2010.04.27-07:38+0000) multi-call binary

Starting pid 340, console /dev/console: '/etc/init.d/rcS'
120+0 records in
120+0 records out
Welcome to Realtek Rescue Linux for PhotoViewer
mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: Unknown error 19
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2

>>>>>> loader start! (Apr 27 2010:15:39:10, version=00.01.01)
Secure Boot is off.

Please press Enter to activate this console. Hotplug: device "ram0" is skipped.
Hotplug: device "loop0" is skipped.
Hotplug: device "loop1" is skipped.
Hotplug: device "loop2" is skipped.
Hotplug: device "loop3" is skipped.
Hotplug: device "loop5" is skipped.
Hotplug: device "loop6" is skipped.
Hotplug: device "loop7" is skipped.
Hotplug: device "mtdblock0" is skipped.
Hotplug: device "loop4" is skipped.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.
Secure Boot is off.


То есть если сварганить переходник USB-B(штекер папа) -- USB-A (гнездо мама) то можно читать флэшки ?
Konos GV3765,Iconbit XDS1003D,Ugoos X3Pro,Vontar x3,Tanix W2
User avatar
kliaoz
 
Posts: 5
Joined: 29 Nov 2022, 02:15

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 30 Nov 2022, 18:06

Code: Select all
sata1: dev 0 ATA, max UDMA/100, 1465149168 sectors: lba48
Vendor: ATA Model: TOSHIBA MQ01ABD0 Rev: AX00
Type: Direct-Access ANSI SCSI revision: 05
scsi1 : SATA_DRV
sata dma reset

диск подключается но не монтируется, вручную его смонтировать то есть шанс что пойдет прошивка...
игнорить флуд loader (Secure Boot is off.)
несколько раз нажать энтер в консоли и влоб (лучше копипастом)
Code: Select all
mkdir -p /tmp/usbmounts/sda1
mount /dev/sda1 /tmp/usbmounts/sda1

То есть если сварганить переходник USB-B(штекер папа) -- USB-A (гнездо мама) то можно читать флэшки ?

в теории да, если не помешает
Code: Select all
Setting registers , Enable OTG
так обычно переводят порт USB-B в отг режим... или по перемычке в разьеме USB-B или если производитель гвоздем в буте переключил порт то безусловно....
но в любом случае если сменить бут и прошивку с отключеным OTG режимиом - порт ваш :D , как и тот что не работает (выпаяв дохлый чип хаба и подключив один разьем напрямую к порту проца)
| +
Снимок экрана от 2022-11-30 19-15-13.png
Снимок экрана от 2022-11-30 19-15-13.png (1.63 MiB) Viewed 3231 times
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby kliaoz » 01 Dec 2022, 20:02

диск подключается но не монтируется, вручную его смонтировать то есть шанс что пойдет прошивка...
игнорить флуд loader (Secure Boot is off.)
несколько раз нажать энтер в консоли и влоб (лучше копипастом)

mkdir -p /tmp/usbmounts/sda1
mount /dev/sda1 /tmp/usbmounts/sda1

Вот тут всё и поехало .,,,,Прошился , Спасибо Virtual ! :o
А USB я обязательно зделаю по вашей наводке.

putty.zip
(18.28 KiB) Downloaded 99 times


У меня вопрос - при следующей прошивке опять проходить этот квест ? Или подключиться телнетом и дать команду echo " " | dd of=/dev/mtdblock/0 bs=2048 seek=8192 или команду kill -6 1
Konos GV3765,Iconbit XDS1003D,Ugoos X3Pro,Vontar x3,Tanix W2
User avatar
kliaoz
 
Posts: 5
Joined: 29 Nov 2022, 02:15

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 01 Dec 2022, 21:39

У меня вопрос - при следующей прошивке опять проходить этот квест ?

обязательно, если USB не починеш :twisted: ток реска в моем буте автоматом монтирует еще и SATA для установки прош....
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby kliaoz » 01 Dec 2022, 22:07

То есть лучше мне поставить бут 1073_7L_avhdd_128x1_pal_rsq.0000.0202.1019.bin это в теме где делается гипертерминалом http://www.moservices.org/forum/viewtopic.php?f=21&t=1463 ?
Konos GV3765,Iconbit XDS1003D,Ugoos X3Pro,Vontar x3,Tanix W2
User avatar
kliaoz
 
Posts: 5
Joined: 29 Nov 2022, 02:15

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby Virtual » 02 Dec 2022, 05:16

да бут 1073_7L_avhdd_128x1_pal_rsq.0000.0202.1019.bin
можно через гипер терминал а можно по tftp
http://www.moservices.org/forum/viewtopic.php?f=8&t=79
марсы: HDS7 (смотрелка AMP скин vrt )
HDR12 AMP (обычно сервер с RAM 256 и 2 SATA диска 2T+)//но очень иногда оцифровка видео
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6862
Joined: 01 Oct 2010, 17:17
Location: RU

Re: Восстановление при самой неудачной прошивке Mars(1073/12

Postby kliaoz » 02 Dec 2022, 19:26

Поставил ваш бут , на всякий пожарный случай - сейчас 0000.0202.1019 . Спасибо Virtual !
Konos GV3765,Iconbit XDS1003D,Ugoos X3Pro,Vontar x3,Tanix W2
User avatar
kliaoz
 
Posts: 5
Joined: 29 Nov 2022, 02:15

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 14 guests

cron