uShare UPnP/DLNA server 1.1a

[kurer]

Спасибо!
Поставил xupnpd, он заработал сразу же.
Показывает какое то видео онлайн, но не нашел как указать локальный каталог с фильмами.

В конфиге найдите строку
-- { './localfiles', 'Local Media Files' }
уберите минусы и поправьте путь. Должно получить типа так
{ '/tmp/usbmounts/sda1', 'Local Media Files' }

Здравствуйте!
К сожалению не смог попробовать предложенные Вами рекомендации.
Сервис перестал запускаться
Ручной запуск, удаление -> установка сервиса непомогла.
Помогите пожалуйста.

[FarVoice]

Может, у вас параллельно запущен ещё mediatomb | ushare | pshare ? Так удалите его

[kurer]

Запущен только Transmission

[FarVoice]

А в логе при попытке запуска модуля что пишет?

[kurer]

/usr/local/etc/mos/etc/init/S35xupnpd start
Starting xupnpd service...

видеоскрин http://www.youtube.com/watch?v=J5TSnIltsmg

[FarVoice]

Ояень странно...
Сделайте
/usr/local/etc/mos/etc/init//S35xupnpd start
dmesg
и покажите лог

[kurer]

Ояень странно...
Сделайте
/usr/local/etc/mos/etc/init//S35xupnpd start
dmesg
и покажите лог

А как?
Через телнет зайти?

[FarVoice]

Да, в телнете

[kurer]

Лог | +

bEndpointAddress=3
#@# cfyeh-debug usb3_mac_setting_saturn(274) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(275) 0xb8028108 = 0x02400008
wMaxPacketSize=200
bInterval=0
RT_usb_endpoint_is_bulk_out = 3

usb_endpoint_descriptor(3):
bLength=7
#@# cfyeh-debug usb3_mac_setting_saturn(280) 0xb8028108 = 0x21010000
bDescriptorType=5
bEndpointAddress=84
wMaxPacketSize=40
bInterval=1
RT_usb_endpoint_is_int_in = 4, Interval = 1
#@# cfyeh-debug usb3_mac_setting_saturn(283) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(284) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(289) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(294) disable usb mulit request
nr_endpoint=4, in_num=2, out_num=2

USB_SPEED_HIGH
Chip Version ID: VERSION_NORMAL_UMC_CHIP_88C_B_CUT.
#@# cfyeh-debug usb3_mac_setting_saturn(295) *(unsigned int volatile *)0xb801320
0=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(297) *(unsigned int volatile *)0xb801320
0=0x0
RF_Type is 3!!
#@# cfyeh-debug usb3_mac_setting_saturn(302) GUSB3PIPECTL
EEPROM type is E-FUSE
====> ReadAdapterInfo8192C
Boot from EFUSE, Autoload OK !
#@# cfyeh-debug usb3_mac_setting_saturn(303) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(306) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(309) ---
EEPROMVID = 0x0bda
EEPROMPID = 0x8176
EEPROMCustomerID : 0x00
EEPROMSubCustomerID: 0x00
RT_CustomerID: 0x00
_ReadMACAddress MAC Address from EFUSE = 0-47-13-0-5f-b5
EEPROMRegulatory = 0x0
_ReadBoardType(0)
BT Coexistance = disable
RT_ChannelPlan: 0x0a
_ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
Realtek Bulid-In SATA Driver Rev:SATURN (2011-02-24 15:10)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
### PS params=> power_mgnt(0),usbss_enable(0) ###
### AntDivCfg(0)
readAdapterInfo_8192CU(): REPLACEMENT = 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA Package<==== ReadAdapterInfo8192C in 340 ms
dvr malloc order: 3
+++ ALLOC index: 9752 order: 3
zone: 80915000 page: 80961300(84618000) count: 8
start remap DVR zone 84618000(80961300) 8...
total migrated: done: 8 fail: 0
dvr malloc order: 3
+++ ALLOC index: 9760 order: 3
zone: 80915000 page: 80961400(84620000) count: 8
start remap DVR zone 84620000(80961400) 8...
total migrated: done: 8 fail: 0
dvr malloc order: 3
+++ ALLOC index: 9768 order: 3
zone: 80915000 page: 80961500(84628000) count: 8
start remap DVR zone 84628000(80961500) 8...
total migrated: done: 8 fail: 0
dvr malloc order: 3
+++ ALLOC index: 9776 order: 3
zone: 80915000 page: 80961600(84630000) count: 8
start remap DVR zone 84630000(80961600) 8...
total migrated: done: 8 fail: 0
rtw_macaddr_cfg MAC Address = 0-47-13-0-5f-b5
MAC Address from pnetdev->dev_addr= 00:47:13:00:5f:b5
bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
usbcore: registered new interface driver rtl8192cu
+rtw_wx_set_enc, flags=0x8403
EncryptionDisabled
+871x_drv - drv_open, bup=0
===> FirmwareDownload91C() fw:Rtl819XFwImageArray_UMC_B
fw_ver=v75, fw_subver=0, sig=0x88c0
fw download ok!
HalDetectPwrDownMode(): PDN=0
HalDetectSelectiveSuspendMode(): SS
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Disable
Set RF Chip ID to RF_6052 and RF type to 1T1R.
ata1.00: HPA detected: current 312581808, native 177702923509424
ata1.00: ATA-8: ST3160813AS, SD22, max UDMA/133
ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3160813AS SD22 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
GPIO_IN=0f
eRfPowerStateToSet=0
IQK:Start!!!
Path A IQK Success!!
Path A IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=ff RegE9C=8 RegEA4=fe RegEAC=2 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
Path A IQ Calibration Success !
pdmpriv->TxPowerTrackControl = 1
MAC Address from REG_MACID = 0-47-13-0-5f-b5
MAC Address = 0-47-13-0-5f-b5
-871x_drv - drv_open, bup=1
ADDRCONF(NETDEV_UP): wlan0: link is not ready
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
set_mode = IW_MODE_INFRA
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
survey done event(b)
sda: sda1 sda2 sda3
data[0] 0xbabeface signature[0] 0xbabeface
data[1] 0xdeadbeef signature[1] 0xdeadbeef
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.5 (Sep 19 2011 18:35:58) LBD=ON with delayalloc with ioctl loaded
at c09b9000
NTFS read/write support included
Hfs+/HfsX read/write support included
Built for: realtek_new_ic_2011-04-29IW_SCAN_THIS_ESSID, ssid=ZyXEL 99:f0:40, len
=14
sd 0:0:0:0: [sda] Attached SCSI disk
ufsd: use builtin utf8 instead of kernel utf8
0xb800036c = 0x555d4844
Realtek Card-Reader Driver Rev:SATURN (2011-07-21 10:50)
rtksdio: power_gpio = 0xb801b110
rtksdio: power_bits = 31
Realtek Card-Reader Controller Driver installation fails.

rtksdio: clk change to 15MHz
mmc0: rtksdio driver initialized,
Realtek Card-Reader Controller Driver is successfully installing.

ufsd: sda1 without journal
EXT4-fs (sda3): warning: mounting unchecked fs, running e2fsck is recommended
EXT4-fs (sda3): mounted filesystem without journal
survey done event(8)
set_mode = IW_MODE_INFRA
wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM

wpa_ie(length:22):
0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x04
0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
=>rtw_wx_set_essid
ssid=ZyXEL 99:f0:40, len=14
#### dst_ssid=(ZyXEL 99:f0:40) Opt_Ant_(B) , cur_Ant(B)
link to new AP
<=rtw_wx_set_essid
link to Ralink AP
OnAction_back
OnAction_back
OnAction_back
OnAuthClient
OnAssocRsp
report_join_res(1)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
WMM(0): 0, a42b
WMM(1): 0, a44f
WMM(2): 0, 5e4322
WMM(3): 0, 2f3222
HTOnAssocRsp
update raid entry, mask=0xfffff, arg=0x80
HW_VAR_BASIC_RATE: BrateCfg(0x15d)
rtl8192c_set_FwJoinBssReport_cmd
SetFwRsvdPagePkt
Set RSVD page location to Fw.
=>mlmeext_joinbss_event_callback

~~~~stastakey:unicastkey

~~~~stastakey:groupkey
==> rtw_set_key algorithm(4),keyid(1),key_mask(2)
save exit: isCheckpointed 1
save exit: isCheckpointed 0
save exit: isCheckpointed 0
init: untracked pid 786 exited
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
rtw_issue_addbareq_cmd, p=0
issue_action_BA, category=3, action=0, status=0
OnAction_back
OnAction_back, action=1
rtw_issue_addbareq_cmd, p=6
issue_action_BA, category=3, action=0, status=6
OnAction_back
OnAction_back, action=1
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
wlan0: no IPv6 routers present
init: untracked pid 421 exited
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
-----------------------------------------
[I2C1] Xfer fail - TXABORT (0/1), Reason=0001
msg->addr = 68
msg->flags = 0000
msg->len = 8
msg->buf = 9ae01e00
-----------------------------------------
==========================================================
do_page_fault() #2: sending SIGSEGV to HiMediaDMA for invalid read access from
00001000 (epc == 1ab4fff0, ra == 1ab48efc)
==========================================================
init: untracked pid 846 exited
IQK:Start!!!
Path A IQK Success!!
Path A IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=fe RegE9C=5 RegEA4=fc RegEAC=3 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
Path A IQ Calibration Success !
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
rtw_issue_addbareq_cmd, p=3
issue_action_BA, category=3, action=0, status=3
OnAction_back
OnAction_back, action=1
init: untracked pid 909 exited
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
rtw_issue_addbareq_cmd, p=1
issue_action_BA, category=3, action=0, status=1
OnAction_back
OnAction_back, action=1
OnAction_back
OnAction_back, action=2
OnAction_back(): DELBA: 0(0)
OnAction_back
OnAction_back, action=2
OnAction_back(): DELBA: 0(0)
OnAction_back
OnAction_back, action=2
OnAction_back(): DELBA: 0(0)
OnAction_back
OnAction_back, action=2
OnAction_back(): DELBA: 0(0)
OnAction_back
OnAction_back, action=2
OnAction_back(): DELBA: 0(0)
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
init: untracked pid 1042 exited
init: untracked pid 1308 exited
init: untracked pid 1310 exited
init: untracked pid 1348 exited
init: untracked pid 1493 exited
init: untracked pid 1841 exited
init: untracked pid 1843 exited
init: untracked pid 1881 exited
init: untracked pid 2026 exited
init: untracked pid 2373 exited
init: untracked pid 2375 exited
init: untracked pid 2413 exited
init: untracked pid 2558 exited
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
Venus IR: report key 0xbd42 217
Venus IR: report key 0xbd42 217
Venus IR: report key 0xff00 158
pli malloc order: 6
+++ ALLOC index: 9792 order: 6
zone: 80915000 page: 80961800(84640000) count: 64
start remap DVR zone 84640000(80961800) 64...
total migrated: done: 64 fail: 0
save exit: isCheckpointed 1
save exit: isCheckpointed 0
save exit: isCheckpointed 0
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
init: untracked pid 3626 exited
init: untracked pid 3628 exited
init: untracked pid 3817 exited
~ #

[FarVoice]

Ничо не понял. У меня абсолютно нормально стартует...
Неплохо бы глянуть, что там в плеере делается... Свяжитесь со мной в скайп farvoice-home