К UART подключился, получил "s/d/g/c>". Путем долгих гуглений нашел нужный hw_settings (https://www.dropbox.com/s/wdl9bkpvb2vpjph/mars.QFP.128x1.t1.bin).
Путем сомнительных манипуляций (честно - сам не понял), с помощью попыток частями загнать во флеш дамп нулевого блока (использовал rtdsr) с последующим запуском 1283.hz.goo_ntsc_rsq.0019.bin, получил рабочий REALTEK ROM Monitor, Revision 0000.0201.1026U. В нем: erase -e и erase -m и получаем запуск rescue образа.
Скачал последний install.img с сайта g-mini, флешку в тело. Наблюдаю процесс запуска обновления, но там "Kernel panic - not syncing: Attempted to kill init!" (лог в конце поста)
Перепробовал разные файлы обновлений, результат практически идентичный...
Других рабочих версий буткодов не нашел...
Подскажите, куда дальше копать?
- Лог | +
- ?hello world!
552820 8wa0it waiA~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A
REALTEK ROM Monitor, Revision 0000.0201.1026U.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.
For a list of available commands, type 'help'.
Compilation time /version= Jan 25 2012 21:38:32 /0000.0201.1026U
MAC address = 00.11.22.33.44.55
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x78
Endianness = Little
Flash memory size = 256 MByte
SDRAM size = 256 MByte
First free SDRAM address = 0x800fe000
Press 'ESC' to Monitor mode
NTSC logo
Realtek> erase -e
Erasing...Done
save env (addr 0xa0010000, size 64KB) to flash...
Realtek> erase -m
/Done
Realtek> reset
Performing reset...
?hello world!
52850 2wa8it0 waiA
REALTEK ROM Monitor, Revision 0000.0201.1026U.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.
For a list of available commands, type 'help'.
Compilation time /version= Jan 25 2012 21:38:32 /0000.0201.1026U
MAC address = 00.11.22.33.44.55
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x78
Endianness = Little
Flash memory size = 256 MByte
SDRAM size = 256 MByte
First free SDRAM address = 0x800fe000
Press 'ESC' to Monitor mode
Signature(яяяяяяяя) error! Entering rescue linux...
Rescue kernel in FLASH, total size = 0xef9f1
seg.1 addr 0xa0a09414, size = 0xef9f1
seg.2 addr 0x0, size = 0x0
copy rescue0: from a0a09414 to 81000000, len = ef9f1
decompressing rescue: from 81000000 to 80100000: size = ef9f1
lzma finished
decompressing rescue done
go 0x80100000 BOOT_TAG=яяяяяяяя
NTSC logo
Reset Ethernet Mac.
Address = 0x80100000
Realtek LINUX (DC ALIAS) started...
Venus setting:
ROSs have 2621440 bytes RAM.
System CPU has 1 UART.
System CPU uses external timer interrupt.
Bootloader version: 0000.0201.1026U. This version string is of new format.
[0m[31;5mError! Unknown SB2_CHIP_INFO. Linux is too old?[0m
Ethernet Mac address: 00.11.22.33.44.55
Model Config length=0
Config serial console: console=ttyS0,115200n8r
prom_flashsize = 0x10000000
Linux version 2.6.12.6-VENUS (alan@localhost.localdomain) (gcc version 3.4.4 mipssde-6.03.01-20051114) #23 Tue Oct 6 10:10:27 CST 2009
**************************************************************
You didn't specify audio image address, use default instead...
**************************************************************
audio addr: 0
CPU revision is: 00019378
Determined physical RAM map:
memory: 00100000 @ 00000000 (usable)
memory: 0032c000 @ 00100000 (reserved)
memory: 01954000 @ 0042c000 (usable)
memory: 00280000 @ 01d80000 (reserved)
memory: 0e000000 @ 02000000 (usable)
show info: max_low_pfn:65536
show info: min_low_pfn:1068
Built 1 zonelists
Kernel command line: BOOT_TAG=яяяяяяяя console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 1024 (order: 10, 16384 bytes)
Estimate value: CPU frequency 405.03 MHz
Using 27.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 252868k/256336k available (1941k kernel code, 3292k reserved, 294k data, 420k init, 0k highmem)
Warning! Unknown board id.
Warning! Unknown board id.
==================== Warning! The calculated loops_per_jiffy is not similar to the default one. ====================
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
Linux NoNET1.0 for Linux 2.6
SCSI subsystem initialized
usbcore: registered new driver hub
se init module major number = 254
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
Hello, Realtek TLB Mapper
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
NTFS driver 2.1.28 [Flags: R/O].
Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize
loop: loaded (max 8 devices)
Mars no support IDE
ide generic info: ide_generic_init
Mars no support IDE
libata version 1.12 loaded.
sata driver initial...2009/09/03
sata dma reset
sata1: reset phy again!
sata phy reset
sata1: reset phy again!
sata phy reset
sata1: reset phy extra!
sata phy reset
sata1: reset phy extra!
sata phy reset
sata1: reset phy extra!
sata phy reset
sata1: phy reset timeout!
sata1: no device found (phy stat 00000000)
sata1: ata_bus_probe failed
scsi0 : SATA_DRV
sata dma reset
sata2: reset phy again!
sata phy reset
sata2: reset phy again!
sata phy reset
sata2: phy reset timeout!
sata2: no device found (phy stat 00000000)
sata2: ata_bus_probe failed
scsi1 : SATA_DRV
VenusSFC MTD init
serial flash inaccessible
physmap flash device: 10000000 at fd00000
Realtek NAND Flash Driver Rev:268236 (2009-09-17)
One HY27UF082G2B chip has 1 die(s) on board
nand part=HY27UF082G2B, id=adda1095, device_size=268435456, chip_size=268435456, num_chips=1, isLastPage=0
[rtk_nand_scan_bbt] have created bbt B0, just loads it !!
[dump_BBT] Nand BBT Content
Congratulation!! No BBs in this Nand.
RTK: using the whole nand as a partitoin
Realtek Nand Flash Driver is successfully installing.
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ehci_hcd ehci_hcd: EHCI Host Controller
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub : individual port power switching
hub : individual port over-current protection
[cfyeh] set PPE = 0
[usb_param] setting for mars
Setting for MARS-B
[usb_param] set port two for host!
[usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
[usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit
[usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit
[usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub : ganged power switching
hub : global over-current protection
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Setting registers , Enable OTG
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Shared Tx FIFO mode
i2c /dev entries driver
=========================
= VER : 1.8
=========================
= PHY : 0
= MODE: MARS
DWC_otg: USB RESET
= SPD : 1
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 8
= RX FIFO DEPTH : 8
= FIFO THRESHOLD: 4
= BUS JAM RECORVER : ON
= NON STOP WRITE : OFF
= SP PROTECT : ON
=========================
=========================
= VER : 1.8
=========================
= PHY : 1
= MODE: MARS
= SPD : 1
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 8
= RX FIFO DEPTH : 8
= FIFO THRESHOLD: 4
= BUS JAM RECORVER : ON
= NON STOP WRITE : OFF
= SP PROTECT : ON
=========================
Freeing prom memory: 0kb freed
Reclaim bootloader memory from 80020000 to 80100000
Freeing unused kernel memory: 420k freed
init started: BusyBox v1.1.3 (2009.10.06-02:08+0000) multi-call binary
Starting pid 336, console /dev/console: '/etc/init.d/rcS'
120+0 records in
120+0 records out
Welcome to Realtek Rescue Linux for PhotoViewer
mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: Unknown error 19
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2
>>>>>> loader start! (Oct 6 2009:10:09:51, version=00.01.01)
Please press Enter to activate this console. usb 1-1.1: new high speed USB device using ehci_hcd and address 3
scsi2 : SCSI emulation for USB Mass Storage devices
Hotplug: device "ram0" is skipped.
Hotplug: device "loop0" is skipped.
Hotplug: device "loop1" is skipped.
Hotplug: device "loop2" is skipped.
Hotplug: device "loop3" is skipped.
Hotplug: device "loop4" is skipped.
Hotplug: device "loop5" is skipped.
Hotplug: device "loop6" is skipped.
Hotplug: device "loop7" is skipped.
Hotplug: device "mtdblock0" is skipped.
usb 1-1.4: new high speed USB device using ehci_hcd and address 4
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB DISK Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
modprobe: module sd_mod not found.
modprobe: failed to load module sd_mod
Vendor: Generic Model: STORAGE DEVICE Rev: 9451
Type: Direct-Access ANSI SCSI revision: 00
modprobe: module sd_mod not found.
modprobe: failed to load module sd_mod
SCSI device sda: 8212480 512-byte hdwr sectors (4205 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 8212480 512-byte hdwr sectors (4205 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0:rmdir: `/var/lock/hotplug/mount_tmp/.sda': Unknown error 2
p1
Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi3, channel 0, id 0, lun 0, type 0
Hotplug: "sda" has partitions.
rmdir: `/var/lock/hotplug/mount_tmp/.sda1': Unknown error 2
rmdir: `/var/lock/hotplug/mount_tmp/.sdb': Unknown error 2
mount: Mounting /dev/scsi/host2/bus0/target0/lun0/part1 on /var/lock/hotplug/mount_tmp/.sda1 failed: Unknown error 19
mount: Mounting /dev/scsi/host2/bus0/target0/lun0/part1 on /var/lock/hotplug/mount_tmp/.sda1 failed: Unknown error 22
Hotplug: mount -t ufsd -o ro,sparse -o nls=utf8 -o umask=0 /dev/scsi/host2/bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1 ret: 255
Hotplug: mount -t ntfs -o ro -o nls=utf8 -o umask=0 /dev/scsi/host2/bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1 ret: 255
Hotplug: mount -t vfat -o ro,shortname=winnt -o utf8 -o umask=0 /dev/scsi/host2/bus0/target0/lun0/part1 /var/lock/hotplug/mount_tmp/.sda1 ret: 0
Hotplug: Mount "sda1" successfully.
mount: Mounting /dev/scsi/host3/bus0/target0/lun0/disc on /var/lock/hotplug/mount_tmp/.sdb failed: Unknown error 19
mount: Mounting /dev/scsi/host3/bus0/target0/lun0/disc on /var/lock/hotplug/mount_tmp/.sdb failed: Unknown error 159
mount: Mounting /dev/scsi/host3/bus0/target0/lun0/disc on /var/lock/hotplug/mount_tmp/.sdb failed: Unknown error 159
mount: Mounting /dev/scsi/host3/bus0/target0/lun0/disc on /var/lock/hotplug/mount_tmp/.sdb failed: Unknown error 159
mount: Mounting /var/lock/hotplug/mount_tmp/.sdb on /mnt/usbmounts/sdb failed: Unknown error 22
Hotplug: "sdb" has no partition.
Hotplug: mount -t ufsd -o ro,sparse -o nls=utf8 -o umask=0 /dev/scsi/host3/bus0/target0/lun0/disc /var/lock/hotplug/mount_tmp/.sdb ret: 255
Hotplug: mount -t ntfs -o ro -o nls=utf8 -o umask=0 /dev/scsi/host3/bus0/target0/lun0/disc /var/lock/hotplug/mount_tmp/.sdb ret: 255
Hotplug: mount -t vfat -o ro,shortname=winnt -o utf8 -o umask=0 /dev/scsi/host3/bus0/target0/lun0/disc /var/lock/hotplug/mount_tmp/.sdb ret: 255
Hotplug: mount -t ext3 -o ro /dev/scsi/host3/bus0/target0/lun0/disc /var/lock/hotplug/mount_tmp/.sdb ret: 255
Hotplug: Mount --move "/mnt/usbmounts/sdb" fail.
command: tar -xaOf /mnt/usbmounts/sda1/install.img install_a > /install_a
tar: memory exhausted
tar: Short header
loader_a.c:verona_load_func:1129 Can not execute command, tar -xaOf /mnt/usbmounts/sda1/install.img install_a > /install_a!
command: tar -xOf /mnt/usbmounts/sda1/install.img install_a > /install_a
AVHDD Verona installer (src rev:***256MB version...
0.97b)......Oct 22 2011 18:15:33
opt_str=(null) , tgt_dev=(nul Memory address 0x40000000
l), compress_strFreeing memory...
ing=(null)
package_file_path=/mnt/usbmounts/sda1/install.img
*******************************try_to_free_pages: free 562
***********
call pli_init
pli initialization...
try_to_free_pages: free 216
try_to_free_pages: free 0
done (778 pages freed)
try_to_free_pages: free 0
1. start remap DVR zone...
fastmode is 100...
map_done is 919...
map_fail is 0...
start[0-3] = {7001a500, 7001a504, 7001a508, 7001a50c}
end[0-3] = {7001a510, 7001a514, 7001a518, 7001a51c}
In my system...
[time] t=000.257
**chip_id = 1283
chip_id&0xF =0x3
SB2 DEBUG CONTROL(0)= 0x0 --> 0x0
SB2 DEBUG CONTROL(1)= 0x0 --> 0x0
SB2 DEBUG CONTROL(2)= 0x0 --> 0x0
SB2 DEBUG CONTROL(3)= 0x0 --> 0x0
SB2 DEBUG CONTROL(4)= 0x0 --> 0x0
SB2 DEBUG CONTROL(5)= 0x0 --> 0x0
SB2 DEBUG CONTROL(6)= 0x0 --> 0x0
SB2 DEBUG CONTROL(7)= 0x0 --> 0x0
SB2 INT = 0x0 --> 0x0
SB2 start addr(0)= 0x12013069 --> 0x0
SB2 end addr(0)= 0x642214 --> 0x0
SB2 start addr(1)= 0x8000301 --> 0x0
SB2 end addr(1)= 0x8001420 --> 0x0
SB2 start addr(2)= 0x10000420 --> 0x0
SB2 end addr(2)= 0x14201880 --> 0x0
SB2 start addr(3)= 0x820002 --> 0x0
SB2 end addr(3)= 0x10d084c6 --> 0x0
SB2 start addr(4)= 0x8001054 --> 0x0
SB2 end addr(4)= 0xa0d0 --> 0x0
SB2 start addr(5)= 0x800484 --> 0x0
SB2 end addr(5)= 0x1041c04 --> 0x0
SB2 start addr(6)= 0x120000 --> 0x0
SB2 end addr(6)= 0x880132 --> 0x0
SB2 start addr(7)= 0x1120b060 --> 0x0
SB2 end addr(7)= 0x3040ac --> 0x0
IS_CHIP(MARS)
Mars...
5280 wait
got .//video_firmware.install.bin
video start addr, ptr=0x41e00000
video image size, cnt=1623760
audio_addr = 0xc081
video_addr = 0xe081
sleep for 3 seconds...
Calling pli_rese[RPC]open for RPC ioctl...
tRPC()...
[RPC]start reset...
[RPC]done...
5280Go Release HW Semaphore.
In my system...
Got encoding system: 1 (NTSC)
call initRPCProxy... done.
call getTVE... done.
call prepareCLNT... done.
[Video Firmware Version] 202884
[Video Binary Built on] Jun 8 2009 10:04:31
try_to_free_pages: free 505
1. start remap DVR zone...
fastmode is 100...
map_done is 45...
map_fail is 0...
try_to_free_pages: free 0
1. start remap DVR zone...
fastmode is 100...
map_done is 0...
map_fail is 0...
try_to_free_pages: free 0
1. start remap DVR zone...
fastmode is 100...
map_done is 0...
map_fail is 0...
==========================================================
#2: sending SIGBUS to install_a for Read or Instruction bus error
address == 063b85f6 (epc == 80110f6c, ra == 8010945c)
==========================================================
Unhandled kernel unaligned access in arch/mips/kernel/unaligned.c::emulate_load_store_insn, line 502[#1]:
Cpu 0
$ 0 : 00000000 10007f01 063fe59e 00000000
$ 4 : 063fe596 8ce40004 00000000 8180bdfc
$ 8 : 8180bdf8 8180be18 00000001 fffffff8
$12 : fffffffe 00000001 00000000 fffffffe
$16 : 8180be18 00000000 00000000 80000000
$20 : 00001005 7ea01000 00000005 ffffffff
$24 : 00000000 0058a61c
$28 : 8180a000 8180bdd0 7ebffbf0 8010945c
Hi : 00000000
Lo : 00000004
epc : 80110f6c Not tainted
ra : 8010945c Status: 10007f03 KERNEL EXL IE
Cause : 48808010
BadVA : 063b85f6
PrId : 00019378
Modules linked in:
Process install_a (pid: 456, threadinfo=8180a000, task=81b31428)
Stack : 8031f3a8 8031f2bc 00000064 00000002 00000000 10007f01 00000000 00000000
8ce532d0 001acd20 00000000 00000012 8180bf30 00000000 00000000 00000000
8010945c 8042c074 8042c07c 0000ffff 8c000000 0000000c 01000000 00000000
00000000 10007f01 00000000 00000000 00000000 0058a208 00108e5c 00108e58
10007f01 8180bf30 00000001 fffffff8 fffffffe 00000001 00000000 fffffffe
...
Call Trace: [<8010945c>] [<80110e78>] [<801290d4>] [<80110e78>] [<801a90f4>] [<8018a4d8>] [<801a7e94>] [<8010945c>] [<80109988>]
Code: 00621824 14600065 00000000 <88830003> 98830000 24020000 1000000c 00000000 24820002
do_page_fault() #2: sending SIGSEGV to install_a for invalid read access from
00000620 (epc == 005891e0, ra == 00663ee0)
current context: 2b4
dvr_asid: 0xb4
########## User stack address: 81a9e000
Page flags: 100007c, index: 1635, count: 0, mapcount: 0
sending signal: 11
Call Trace: [<8013e81c>] [<80114300>] [<80113fd4>] [<8010d780>] [<801a9d60>] [<801a9d40>] [<801aaa04>] [<801aa9f4>] [<801a9d78>] [<801148a0>] [<80108f70>]
clear pli setting....
==========================================================
#2: sending SIGBUS to init for Read or Instruction bus error
address == 55555aa9 (epc == 80110f6c, ra == 8010945c)
==========================================================
Unhandled kernel unaligned access in arch/mips/kernel/unaligned.c::emulate_load_store_insn, line 502[#2]:
Cpu 0
$ 0 : 00000000 10007f00 5555555d 00000000
$ 4 : 55555559 8ce40004 00000000 81d1fdfc
$ 8 : 81d1fdf8 81d1fe18 00000000 807fc000
$12 : 00000001 00000000 9400a600 00989645
$16 : 81d1fe18 00000000 00000000 80000000
$20 : 00000001 00000000 00000000 00000000
$24 : ffffffff 0043e4f0
$28 : 81d1e000 81d1fdd0 00000000 8010945c
Hi : 00000000
Lo : 00000009
epc : 80110f6c Not tainted
ra : 8010945c Status: 10007f03 KERNEL EXL IE
Cause : 48808010
BadVA : 55555aa9
PrId : 00019378
Modules linked in:
Process init (pid: 1, threadinfo=81d1e000, task=8066bbd8)
Stack : 801148a0 00000001 81908f1c 00000001 81908e00 81d1ff30 81d1ff30 00000000
00000000 10007f01 00000000 00000000 81d1ff30 00000000 7f919db8 00000001
8010945c 00007f00 00000000 807fc000 00000001 00000000 9400a600 00989645
00000000 10007f00 00000000 00000000 00000000 7f919db8 0043e514 0043e510
10007f01 81d1ff30 00000000 807fc000 00000001 00000000 9400a600 00989645
...
Call Trace: [<801148a0>] [<8010945c>] [<80110e78>] [<801290d4>] [<8012ac1c>] [<80110e78>] [<80136aa4>] [<8010945c>] [<80108f2c>]
Code: 00621824 14600065 00000000 <88830003> 98830000 24020000 1000000c 00000000 24820002
Kernel panic - not syncing: Attempted to kill init!
