Wi-Fi USB адаптеры (проверенные)

о железе плеера и о периферии

Re: Wi-Fi USB адаптеры (проверенные)

Postby 123serge123 » 08 May 2016, 21:58

А в логах чего-нибудь пишет? В смысле вывод команды dmesg хотелось бы глянуть во время попыток подключения или сканирования.
123serge123
 
Posts: 186
Joined: 02 Oct 2010, 08:49

Re: Wi-Fi USB адаптеры (проверенные)

Postby fakir » 08 May 2016, 22:23

Вывод команды ifconfig -a
Code: Select all
~ # ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:CE:39:B4:8B:F9
          inet addr:192.168.1.6  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:898275 errors:0 dropped:0 overruns:0 frame:0
          TX packets:232054 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1309411846 (1.2 GiB)  TX bytes:18398896 (17.5 MiB)
          Interrupt:2 Base address:0x6000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:49 errors:0 dropped:0 overruns:0 frame:0
          TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4475 (4.3 KiB)  TX bytes:4475 (4.3 KiB)

wlan0     Link encap:Ethernet  HWaddr 00:E0:4C:82:07:AB
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Если даю команду iwlist wlan0 scanning приходит ответ
Code: Select all
wlan0     Interface doesn't support scanning.

В dmesg при этом чисто.
Iconbit XDS7GL, inext_tv_1.24_moS_r1
fakir
 
Posts: 13
Joined: 25 Apr 2016, 16:32

Re: Wi-Fi USB адаптеры (проверенные)

Postby Witold » 30 Sep 2016, 00:12

Люди! Кто умеет! Соберите драйвер для TP-LINK TL-WN823N
Realtek chip set RTL8192EU
VID_2357 PID_0109
Нужен для плеера
Konoos GV-4000
прошивка inext_tv_1.24_moS_r1

Пробовал сам запустить но не получилось
8192eu.ko добавил, в modules.alias, modules.dep, modules.usbmap прописал, но не гугу
Konoos GV-4000
прошивка inext_tv_1.24_moS_r1 - UPD 25.02.2016 17:40
буткод 0000.0303.0025-iNe2T-5
User avatar
Witold
 
Posts: 17
Joined: 14 May 2015, 00:57

Re: Wi-Fi USB адаптеры (проверенные)

Postby Witold » 01 Oct 2016, 06:18

(cut) overquoting! Пункт 4.19 Правил форума!

Чип по началу искал по FCC ID TE7WN823NV2 тут
но после многих неудач, взял и вскрыл свое устройство и убедился что так и есть RTL8192EU
Konoos GV-4000
прошивка inext_tv_1.24_moS_r1 - UPD 25.02.2016 17:40
буткод 0000.0303.0025-iNe2T-5
User avatar
Witold
 
Posts: 17
Joined: 14 May 2015, 00:57

Re: Wi-Fi USB адаптеры (проверенные)

Postby Witold » 02 Oct 2016, 00:44

Так и не заработал TP-LINK TL-WN823N
драйвер не подошел, подозреваю что в драйвере 8192eu.ko.1186.tar.bz2 нет VID_2357 PID_0109
даже не знаю куда дальше копать
можно купить другой, но не попаду снова в тукую же ситуацию
Konoos GV-4000
прошивка inext_tv_1.24_moS_r1 - UPD 25.02.2016 17:40
буткод 0000.0303.0025-iNe2T-5
User avatar
Witold
 
Posts: 17
Joined: 14 May 2015, 00:57

Re: Wi-Fi USB адаптеры (проверенные)

Postby Virtual » 03 Oct 2016, 07:38

в драйвер что выше дал, был принудительно добавлен VID_2357 PID_0109
| +
modinfo 8192eu.ko
filename: 8192eu.ko
license: GPL
description: Realtek Wireless Lan Driver
author: Realtek Semiconductor Corp.
version: v4.2.4.1_9581.20131119
vermagic: 2.6.34-VENUS preempt mod_unload modversions MIPS32_R2 32BIT
depends:
alias: usb:v2357p0109d*dc*dsc*dp*icFFiscFFipFF*
alias: usb:v0BDAp818Bd*dc*dsc*dp*icFFiscFFipFF*
alias: usb:v0BDAp818Cd*dc*dsc*dp*icFFiscFFipFF*

так что будьте добры:

свисток не тыкать!
Code: Select all
dmesg -c

включить запись логов
Code: Select all
insmod /путьдофайла/8192eu.ko

воткнуть свисток, и подождать 12сек, и потом
Code: Select all
dmesg
ifconfig -a

лог сюда
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6542
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Wi-Fi USB адаптеры (проверенные)

Postby Witold » 04 Oct 2016, 15:33

Вот весь лог действий

| +
iNeXT_TV_517 login: root


BusyBox v1.1.3 (2016.02.08-16:32+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ # dmesg -c
nel utf8
*****video is ready...
*****audio is ready...
***256MB version...
Memory address 0x40000000
ufsd: sda1 without journal
***************** se open: queue = 0 *********************
***************** se open: initialized = 0 *********************
arch/mips/realtek-boards/drivers/se.c, 665: offset = 0, se_devices = 8d038000
arch/mips/realtek-boards/drivers/se.c, 675: offset = 0
arch/mips/realtek-boards/drivers/se.c, 719: length = 20480
arch/mips/realtek-boards/drivers/se.c, 720: offset = 218333184
arch/mips/realtek-boards/drivers/se.c, 727: offset = 218333184
arch/mips/realtek-boards/drivers/se.c, 665: offset = 98316, se_devices = 8d03800 0
arch/mips/realtek-boards/drivers/se.c, 675: offset = 402702336
arch/mips/realtek-boards/drivers/se.c, 719: length = 4096
arch/mips/realtek-boards/drivers/se.c, 720: offset = 402702336
arch/mips/realtek-boards/drivers/se.c, 727: offset = 402702336
fusion: unable to register major 247. Registered 245 instead
+++ ALLOC index: 2048 order: 9
1. start remap DVR zone 81800000(805c9000) 512...
map_done is 221...
+++ ALLOC index: 2560 order: 7
1. start remap DVR zone 81a00000(805cd000) 128...
map_done is 128...
[I2C0] i2c speed changed to 50 KHz
+++ ALLOC index: 2688 order: 7
1. start remap DVR zone 81a80000(805ce000) 128...
map_done is 128...
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
+++ ALLOC index: 0 order: 8
1. start remap DVR zone 81000000(805b9000) 256...
map_done is 256...
+++ ALLOC index: 45056 order: 12
1. start remap DVR zone 8c000000(80719000) 4096...
map_done is 0...
+++ ALLOC index: 512 order: 9
1. start remap DVR zone 81200000(805bd000) 512...
map_done is 512...
+++ ALLOC index: 40960 order: 12
1. start remap DVR zone 8b000000(806f9000) 4096...
map_done is 0...
+++ ALLOC index: 1024 order: 9
1. start remap DVR zone 81400000(805c1000) 512...
map_done is 512...
+++ ALLOC index: 36864 order: 12
1. start remap DVR zone 8a000000(806d9000) 4096...
map_done is 0...
+++ ALLOC index: 32768 order: 12
1. start remap DVR zone 89000000(806b9000) 4096...
map_done is 0...
+++ ALLOC index: 28672 order: 12
1. start remap DVR zone 88000000(80699000) 4096...
map_done is 0...
+++ ALLOC index: 24576 order: 10
1. start remap DVR zone 87000000(80679000) 1024...
map_done is 0...
+++ ALLOC index: 25600 order: 10
1. start remap DVR zone 87400000(80681000) 1024...
map_done is 0...
+++ ALLOC index: 256 order: 3
1. start remap DVR zone 81100000(805bb000) 8...
map_done is 8...
+++ ALLOC index: 20480 order: 12
1. start remap DVR zone 86000000(80659000) 4096...
map_done is 0...
+++ ALLOC index: 16384 order: 12
1. start remap DVR zone 85000000(80639000) 4096...
map_done is 0...
This is the current time: PowerUP_Done!!!

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.
[usb_param] setting for jupiter
#######[cfyeh-debug] USBPHY_Register_Setting(903) jupiter D
[usb_param] set port two for host!
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_39(427) tx_delay 2
port 1 will be stop!
mars_sata_work_fn
device removed from sata port0
mars_sata_work_fn(1168): no cmd Q
mars_sata_work_fn(1199) hot plug end
host_set->ahost_hp_event:0x0
[usb1_param] usbphy reg 32, set sh = 0x8, get sh = 0x8, 4bit
[usb1_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb1_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb1_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb1_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb1_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb2_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb2_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb2_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb2_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
mars_sata_work_fn
device plug into sata port0
sata phy reset
ehci_hcd ehci_hcd: EHCI Host Controller
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub : individual port power switching
hub : individual port over-current protection
[cfyeh] set PPE = 0
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[usb_param] setting for jupiter
#######[cfyeh-debug] USBPHY_Register_Setting(903) jupiter D
[usb_param] set port two for host!
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_39(427) tx_delay 2
sata1: occupy port0, COMRESET ok, sstatus = 123, SCRstatus = 123
__mars_sata_phy_reset(949)check taskfile state
__mars_sata_phy_reset(951)tf status:50
ata_dev_identify(1477)do ATA identify
sata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4123 85:7469 86:be41 87:4123 88:407f
sata1: dev 0 ATA, max UDMA/133, 1953525168 sectors: lba48
Vendor: ATA Model: WDC WD10EADS-00L Rev: 01.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB)
SCSI device sda: drive cache: write back
disk->capacity:0x74706db0
SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB)
SCSI device sda: drive cache: write back
disk->capacity:0x74706db0
/dev/scsi/host0/bus0/target0/lun0: p1
data[0] 0x0 signature[0] 0xbabeface
data[1] 0x0 signature[1] 0xdeadbeef
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
mars_sata_work_fn(1199) hot plug end
[usb1_param] usbphy reg 32, set sh = 0x8, get sh = 0x8, 4bit
[usb1_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb1_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb1_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb1_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb1_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb2_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb2_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb2_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb2_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
~ # insmod /lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/usb/rtl8192eu/drv/8192eu.ko
insmod: cannot insert `/lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/usb/rtl8192eu/drv/8192eu.ko': Invalid module format (-1): Exec format error
~ # dmesg
8192eu: version magic '2.6.34-VENUS preempt mod_unload modversions MIPS32_R2 32BIT ' should be '2.6.12.6-VENUS preempt gcc-3.4'
#######[cfyeh-debug] hub_events(3177) usb_plug_status 1
usb 1-2: new high speed USB device using ehci_hcd and address 2
#######[cfyeh-debug] hub_events(3193) usb_plug_status 0
~ # ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:11:22:C4:B1:47
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:379 errors:0 dropped:0 overruns:0 frame:0
TX packets:466 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:38787 (37.8 KiB) TX bytes:99953 (97.6 KiB)
Interrupt:2 Base address:0x6000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:919 errors:0 dropped:0 overruns:0 frame:0
TX packets:919 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:104216 (101.7 KiB) TX bytes:104216 (101.7 KiB)

~ #
Konoos GV-4000
прошивка inext_tv_1.24_moS_r1 - UPD 25.02.2016 17:40
буткод 0000.0303.0025-iNe2T-5
User avatar
Witold
 
Posts: 17
Joined: 14 May 2015, 00:57

Re: Wi-Fi USB адаптеры (проверенные)

Postby Virtual » 04 Oct 2016, 15:50

дык драйвер под 1186 :mrgreen: вам он не подойдет.
insmod: cannot insert `/lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/usb/rtl8192eu/drv/8192eu.ko': Invalid module format (-1): Exec format error
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6542
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Wi-Fi USB адаптеры (проверенные)

Postby Virtual » 04 Oct 2016, 18:47

rtl8192eu для двух платформ, пробуем.
8192eu.ko.1186.tar.bz2
(440.42 KiB) Downloaded 169 times
(3430)
8192eu.ko.1xx3.tar.bz2
(435.02 KiB) Downloaded 170 times
(1228)

alias:          usb:v0BDAp818Cd*dc*dsc*dp*icFFiscFFipFF*
alias: usb:v0BDAp818Bd*dc*dsc*dp*icFFiscFFipFF*
alias: usb:v2357p0109d*dc*dsc*dp*icFFiscFFipFF*
alias: usb:v2001p3319d*dc*dsc*dp*icFFiscFFipFF*


PSPS на прошивке AMP, если взлетит, подмените родной модуль! (и обязательно отпишитесь - дабы в будущем добавил в хотплаг)
/lib/modules/2.6.12.6-VENUS/kernel/dr~net/wireless/amp/rtl8188eu/8188eu.ko
PSPS ходят слухи что модули ядра от марса иногда на юпитере летают :geek:
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6542
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: Wi-Fi USB адаптеры (проверенные)

Postby Witold » 06 Oct 2016, 15:22

На первом файле снова не под чип 1185
| +
insmod /lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/usb/rtl8192eu/drv/8192eu.ko
insmod: cannot insert `/lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/usb/rtl8192eu/drv/8192eu.ko': Invalid module format (-1): Exec format error


На второй драйвер 8192eu.ko.1xx3.tar.bz2 при втыкании свистка на экране светился знак расмпознания вайфая но так и незапустилось
такой лог
| +
iNeXT_TV_456 login: root


BusyBox v1.1.3 (2016.02.08-16:32+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ # dmesg -c
*256MB version...
Memory address 0x40000000
***************** se open: queue = 0 *********************
***************** se open: initialized = 0 *********************
arch/mips/realtek-boards/drivers/se.c, 665: offset = 0, se_devices = 8d038000
arch/mips/realtek-boards/drivers/se.c, 675: offset = 0
arch/mips/realtek-boards/drivers/se.c, 719: length = 20480
arch/mips/realtek-boards/drivers/se.c, 720: offset = 218333184
arch/mips/realtek-boards/drivers/se.c, 727: offset = 218333184
arch/mips/realtek-boards/drivers/se.c, 665: offset = 98316, se_devices = 8d038000
arch/mips/realtek-boards/drivers/se.c, 675: offset = 402702336
arch/mips/realtek-boards/drivers/se.c, 719: length = 4096
arch/mips/realtek-boards/drivers/se.c, 720: offset = 402702336
arch/mips/realtek-boards/drivers/se.c, 727: offset = 402702336
fusion: unable to register major 247. Registered 245 instead
+++ ALLOC index: 2048 order: 9
1. start remap DVR zone 81800000(805c9000) 512...
map_done is 114...
retry remapping...
1. start remap DVR zone 81800000(805c9000) 512...
map_done is 2...
[I2C0] i2c speed changed to 50 KHz
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
shmpool_ioctl: +
+++ ALLOC index: 2560 order: 7
1. start remap DVR zone 81a00000(805cd000) 128...
map_done is 128...
+++ ALLOC index: 45056 order: 12
1. start remap DVR zone 8c000000(80719000) 4096...
map_done is 0...
+++ ALLOC index: 2688 order: 7
1. start remap DVR zone 81a80000(805ce000) 128...
map_done is 128...
+++ ALLOC index: 40960 order: 12
1. start remap DVR zone 8b000000(806f9000) 4096...
map_done is 0...
+++ ALLOC index: 36864 order: 12
1. start remap DVR zone 8a000000(806d9000) 4096...
map_done is 0...
+++ ALLOC index: 0 order: 8
1. start remap DVR zone 81000000(805b9000) 256...
map_done is 256...
+++ ALLOC index: 32768 order: 12
1. start remap DVR zone 89000000(806b9000) 4096...
map_done is 0...
+++ ALLOC index: 512 order: 9
1. start remap DVR zone 81200000(805bd000) 512...
map_done is 512...
+++ ALLOC index: 1024 order: 9
1. start remap DVR zone 81400000(805c1000) 512...
map_done is 512...
+++ ALLOC index: 28672 order: 12
1. start remap DVR zone 88000000(80699000) 4096...
map_done is 0...
+++ ALLOC index: 24576 order: 10
1. start remap DVR zone 87000000(80679000) 1024...
map_done is 0...
+++ ALLOC index: 25600 order: 10
1. start remap DVR zone 87400000(80681000) 1024...
map_done is 0...
+++ ALLOC index: 256 order: 3
1. start remap DVR zone 81100000(805bb000) 8...
map_done is 8...
+++ ALLOC index: 20480 order: 12
1. start remap DVR zone 86000000(80659000) 4096...
map_done is 0...
+++ ALLOC index: 16384 order: 12
1. start remap DVR zone 85000000(80639000) 4096...
map_done is 0...
This is the current time: PowerUP_Done!!!

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.
[usb_param] setting for jupiter
#######[cfyeh-debug] USBPHY_Register_Setting(903) jupiter D
[usb_param] set port two for host!
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_39(427) tx_delay 2
port 1 will be stop!
mars_sata_work_fn
device removed from sata port0
mars_sata_work_fn(1168): no cmd Q
mars_sata_work_fn(1199) hot plug end
host_set->ahost_hp_event:0x0
[usb1_param] usbphy reg 32, set sh = 0x8, get sh = 0x8, 4bit
[usb1_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb1_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb1_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb1_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb1_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb2_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb2_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb2_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb2_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
ehci_hcd ehci_hcd: EHCI Host Controller
mars_sata_work_fn
device plug into sata port0
sata phy reset
ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1
ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000
ehci_hcd ehci_hcd: park 0
ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub : individual port power switching
hub : individual port over-current protection
sata1: occupy port0, COMRESET ok, sstatus = 123, SCRstatus = 123
__mars_sata_phy_reset(949)check taskfile state
__mars_sata_phy_reset(951)tf status:50
ata_dev_identify(1477)do ATA identify
sata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4123 85:7469 86:be41 87:4123 88:407f
sata1: dev 0 ATA, max UDMA/133, 1953525168 sectors: lba48
Vendor: ATA Model: WDC WD10EADS-00L Rev: 01.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB)
SCSI device sda: drive cache: write back
disk->capacity:0x74706db0
SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB)
SCSI device sda: drive cache: write back
disk->capacity:0x74706db0
/dev/scsi/host0/bus0/target0/lun0:[cfyeh] set PPE = 0
p1
data[0] 0x0 signature[0] 0xbabeface
data[1] 0x0 signature[1] 0xdeadbeef
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[usb_param] setting for jupiter
#######[cfyeh-debug] USBPHY_Register_Setting(903) jupiter D
[usb_param] set port two for host!
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 1 dr 1
mars_sata_work_fn(1199) hot plug end
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(238) port 2 dr 1
#@# cfyeh-debug USBPHY_SetReg_Default_39(427) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0x8, get sh = 0x8, 4bit
[usb1_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb1_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb1_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb1_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb1_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x6, get src = 0x6, 3bit
[usb2_param] usbphy reg 36, set senh = 0x9, get senh = 0x9, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x1, get dr = 0x1, 3bit
[usb2_param] usbphy reg 31, set sr = 0x7, get sr = 0x7, 3bit
[usb2_param] usbphy reg 30, set cp = 0x1, get cp = 0x1, 3bit
[usb2_param] usbphy reg 30, set sc = 0x3, get sc = 0x3, 4bit
ohci_hcd ohci_hcd: OHCI Host Controller
ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2
ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub : no power switching (usb 1.0)
hub : no over-current protection
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
ufsd: use builtin utf8 instead of kernel utf8
ufsd: sda1 without journal
~ # insmod /lib/modules/2.6.12.6-VENUS/kernel/drivers/net/wireless/realtek/usb/rtl8192eu/drv/8192eu.ko
~ # dmesg
RTL871X: module init start
RTL871X: rtl8192eu driver version = v4.2.4.1_9581.20131119
RTL871X: build time: Oct 4 2016 17:37:02
usbcore: registered new driver rtl8192eu
RTL871X: module init ret=0
#######[cfyeh-debug] hub_events(3177) usb_plug_status 1
usb 1-2: new high speed USB device using ehci_hcd and address 2
RTL871X:
usb_endpoint_descriptor(0):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=84
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_in = 4
RTL871X:
usb_endpoint_descriptor(1):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=5
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_out = 5
RTL871X:
usb_endpoint_descriptor(2):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=6
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_out = 6
RTL871X:
usb_endpoint_descriptor(3):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=87
RTL871X: wMaxPacketSize=64
RTL871X: bInterval=3
RTL871X: RT_usb_endpoint_is_int_in = 7, Interval = 3
RTL871X:
usb_endpoint_descriptor(4):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=8
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_out = 8
RTL871X: nr_endpoint=5, in_num=2, out_num=3

RTL871X: USB_SPEED_HIGH
RTL871X: CHIP TYPE: RTL8192E
+++ ALLOC index: 288 order: 5
1. start remap DVR zone 81120000(805bb400) 32...
map_done is 32...
RTL871X: ReadChipVersion192e 0xF0 = 0xc441135
RTL871X: Chip Version Info: CHIP_8192E_Normal_Chip_SMIC_B_CUT_2T2R_RomVer(0)
RTL871X: RF_Type is 2!!
RTL871X: _ConfigChipOutEP_8192E OutEpQueueSel(0x07), OutEpNumber(3)
RTL871X: ====> ReadAdapterInfo8192EU
#######[cfyeh-debug] store_check_change_field(504) usb_plug_status 1
RTL871X: Boot from EFUSE, Autoload OK !
RTL871X: EEPROM ID=0x8129
RTL871X: VID = 0x2357, PID = 0x0109
RTL871X: Customer ID: 0x00, SubCustomer ID: 0xCD
RTL871X: hal_ReadMACAddress_8192EU MAC Address from EFUSE = 98:de:d0:0b:a3:d6
RTL871X: EEPROMRegulatory = 0x1 TxPwrCalibrateRate=0x0
RTL871X: Board Type: Dongle or WIFI only Module
RTL871X: mlmepriv.ChannelPlan = 0x21
RTL871X: CrystalCap: 0x1a
RTL871X: ThermalMeter = 0x20
RTL871X: SWAS: bHwAntDiv = 0, TRxAntDivType = ff
RTL871X: pHalData->PAType_2G is 0x0, pHalData->ExternalPA_2G = 0
RTL871X: pHalData->LNAType_2G is 0x0, pHalData->ExternalLNA_2G = 0
RTL871X: ReadAdapterInfo8192EU <====
+++ ALLOC index: 320 order: 5
1. start remap DVR zone 81140000(805bb800) 32...
map_done is 32...
RTL871X: init_channel_set ChannelPlan ID 21 Chan num:13
+++ ALLOC index: 272 order: 4
1. start remap DVR zone 81110000(805bb200) 16...
map_done is 16...
+++ ALLOC index: 264 order: 3
1. start remap DVR zone 81108000(805bb100) 8...
map_done is 8...
+++ ALLOC index: 352 order: 3
1. start remap DVR zone 81160000(805bbc00) 8...
map_done is 8...
+++ ALLOC index: 360 order: 3
1. start remap DVR zone 81168000(805bbd00) 8...
map_done is 8...
+++ ALLOC index: 368 order: 3
1. start remap DVR zone 81170000(805bbe00) 8...
map_done is 8...
+++ ALLOC index: 384 order: 4
1. start remap DVR zone 81180000(805bc000) 16...
map_done is 16...
+++ ALLOC index: 400 order: 4
1. start remap DVR zone 81190000(805bc200) 16...
remap: reinitialize swap area...
map_done is 16...
RTL871X: rtw_macaddr_cfg MAC Address = 98:de:d0:0b:a3:d6
RTL871X: bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
RTL871X: rtw_ndev_init(wlan0)
RTL871X: _rtw_drv_register_netdev, MAC Address (if1) = 98:de:d0:0b:a3:d6
#######[cfyeh-debug] hub_events(3193) usb_plug_status 0

eth0: Set multicast.

eth0: Set multicast.
RTL871X: +871x_drv - drv_open, bup=0
RTL871X: ==>_InitPowerOn_8192EU
RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
RTL871X: ===> FirmwareDownload88E() fw source from Header.
RTL871X: ===> Firmware for NIC fw:FirmwareDownload8192E, size: 32482
RTL871X: FirmwareDownload8192E: fw_ver=16 fw_subver=0 sig=0x92e1
RTL871X: FirmwareDownload8192E writeFW_retry:0, time after fwdl_start_time:40ms
RTL871X: _FWFreeToGo8192E: Checksum report OK! REG_MCUFWDL:0x00070304
RTL871X: =====> _8051Reset8192E(): 8051 reset success .
RTL871X: _FWFreeToGo8192E: Polling FW ready success!! REG_MCUFWDL:0x000702c6
RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
RTL871X: PHY_ConfigRFWithPowerLimitTableParaFile(): No File rtl192E/TXPWR_LMT.txt, Load from HWImg Array!
RTL871X: phy_ConfigBBWithPgParaFile(): No File rtl192E/PHY_REG_PG.txt, Load from HWImg Array!
RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x1a
RTL871X: Auto InitLLTTable8192E success
RTL871X: pDM_Odm TxPowerTrackControl = 1
RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
RTL871X: ===FixSpur NOT Pass!
RTL871X: MAC Address from REG_MACID = 98:de:d0:0b:a3:d6
RTL871X: rtl8192eu_hal_init in 1660ms
RTL871X: MAC Address = 98:de:d0:0b:a3:d6
RTL871X: -871x_drv - drv_open, bup=1

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.

eth0: Set multicast.
RTL871X: ==>rtw_ps_processor .fw_state(0)
RTL871X: ==>ips_enter cnts:1
RTL871X: nolinked power save enter
RTL871X: ===> rtw_ips_pwr_down...................
RTL871X: ====> rtw_ips_dev_unload...
RTL871X: usb_read_port_cancel
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(0) OR bSurpriseRemoved(0) bReadPortCancel(1)
RTL871X: usb_write_port_cancel
RTL871X: ==> rtl8192eu_hal_deinit
RTL871X: bkeepfwalive(0)
RTL871X: hal_poweroff_8192eu
RTL871X: SetHwReg8192E: bMacPwrCtrlOn=0
RTL871X: <=== rtw_ips_pwr_down..................... in 140ms
~ # ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:11:22:C4:B1:47
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:111 errors:0 dropped:0 overruns:0 frame:0
TX packets:276 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8333 (8.1 KiB) TX bytes:65579 (64.0 KiB)
Interrupt:2 Base address:0x6000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

wlan0 Link encap:Ethernet HWaddr 98:DE:D0:0B:A3:D6
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

~ #
Konoos GV-4000
прошивка inext_tv_1.24_moS_r1 - UPD 25.02.2016 17:40
буткод 0000.0303.0025-iNe2T-5
User avatar
Witold
 
Posts: 17
Joined: 14 May 2015, 00:57

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 3 guests