Восстановление при самой неудачной прошивке Saturn(1186)

о железе плеера и о периферии

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby Virtual » 06 Feb 2016, 15:05

силовые, по фото плохо видно но сам догадаешся... как связать + одного и другого кондера.
U24 силовой ключь что обрывает питание практически на всю плату
марсы: HDS7 (смотрелка AMP скин vrt уже без вариантов)
HDR12 AMP (обычно сервер с RAM 256 и возможностью подключить 2 SATA диска 2T+)
XTR PRO(AMP, HTTP(S) NFS SMB FTP сервер +trans2.90 + 2 SATA диска 2T+
сатурны: XTR Prodigy, R6S(512Mb_NAND), HD900A(_MD*) прошивка
User avatar
Virtual
 
Posts: 6466
Joined: 01 Oct 2010, 17:17
Location: UFA RU

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby pepelats » 06 Feb 2016, 16:44

Здравствуйте,

Возникла проблема с плеером, после выключения не загружается. На дисплее NUPGRADE, через USB проходит обновление, но не помогает. Купил преобразователь USB-TTL. Посмотрел логи:

Code: Select all
?hello.world
efghhhhhhhhhhhhhhhhhhhhhhhhhhihhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhjk
 Jump!
Orginal init value: 222272BD
cde
profile->manufacturer_id (first 4B):DA94D7AD
profile->data_per_page:2000
profile->page_per_block:100

blk 79 starts from page 700
klmnopqrstu5280 wait5280 wait4K&Detect H27UBG8T2B and enable read-retrial mode...
Enable Read-retrial mode...
load bbt...load env to (addr 0xa0010000, size 64KB)...
page_start=0xf00 page_end=0x1900
!

$$run 1,[Run 0]
!

$$run 2,[Run 0]
!

$$run 3,[Run 0]
!

$$run 4,[Run 0]
load factory to (addr 0x80100000)...
load bbt...ping_no =0xff
pong_no =0xff
there is no data in ping ,pong buffer
current_factory_start=0x1900
current_factory_start + 0x400=0x1d00
tar end,not found
tar end,not found
default_tv_system=
new default_tv_system=PAL
EPHY: 8211E

check_val=0x0

[HDMI]: Set I2C Speed = 50 kHz

[HDMI]: Chk_HotPlug() TV is not connected.

[HDMI]: Read_EDID abort, HDMI cable plug off.

[HDMI]: TV is not connected.

2nd for PAL

PAL logo

[VFD] init


REALTEK ROM Monitor, Revision KIIE.0402.1067.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version=      Feb 20 2014  16:19:33  /KIIE.0402.1067

MAC address =                   00.ce.39.bd.37.ba

Processor Company ID/options =  0x01 (MIPS Technologies, Inc.) / 0x00

Processor ID/revision =         0x93 / 0x85

Endianness =                    Little
Flash memory size =             4 GByte

SDRAM size =                    512 MByte

First free SDRAM address =      0x800c5000


Press 'ESC' to Monitor mode

____________________[VFDSTR]  LOADING

Set ethernet register: 00000044

NAND Signature(RESCUE__) error! Entering rescue linux...

[VFDSTR] NUPGRADE

Rescue kernel in FLASH, total size = 0x1f52d0

seg.1 addr 0xa0a04b0b, size = 0x1f52d0

seg.2 addr 0x0, size = 0x0

copy rescue0: from a0a04b0b to 81000000, len = 1f52d0

decompressing rescue: from 81000000 to 80100000: size = 1f52d0

lzma finished

decompressing rescue done

go 0x80100000 

defer 625p logo

Reset Ethernet Mac.




Address = 0x80100000

Linux version 2.6.34-VENUS (william@rtdmpsa-05) (gcc version 4.3.6 20110218 (prerelease) (GCC) ) #21 PREEMPT Wed Dec 4 13:08:14 CST 2013

Realtek LINUX started...
Venus setting:
   ROSs have 4194304 bytes RAM.
   System CPU has 1 UART.
   System CPU uses internal timer interrupt.
   Bootloader version: KIIE.0402.1067. This version string is of new format.
   The information of this board: Company ID:0x0    CPU ID: 0x4    Board ID: 0x402
   Ethernet Mac address: 00.CE.39.BD.37.BA
   Model Config length=3
Base year of RTC is 2010.
**************************************************************
You didn't specify audio image address, use default instead...
**************************************************************
audio addr: 0
Config serial console: console=ttyS0,115200n8r
bootconsole [early0] enabled
CPU revision is: 00019385 (MIPS 24Kc)
FPU revision is: 01739300
Determined physical RAM map:
 memory: 00020000 @ 00000000 (reserved)
 memory: 000e0000 @ 00020000 (ROM data)
 memory: 01b00000 @ 00100000 (usable)
 memory: 00400000 @ 01c00000 (reserved)
 memory: 0e000000 @ 02000000 (usable)
 memory: 00100000 @ 10000000 (reserved)
 memory: 07f00000 @ 10100000 (usable)
 memory: 00100000 @ 18000000 (reserved)
 memory: 05b00000 @ 18100000 (usable)
Wasting 8192 bytes for tracking 256 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  DMA      0x00000000 -> 0x00002000
  Normal   0x00002000 -> 0x0001dc00
Movable zone start PFN for each node
  Node 0: 64512
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x0001dc00
zone DMA    size: 2000    realsize: 2000
zone Normal    size: dc00    realsize: dc00
zone Movable    size: e000    realsize: e000
zonelist: Movable Normal DMA
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 121856
Kernel command line:  console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255.0.0.0:::
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0004faf9
Readback ErrCtl register=0004faf9
Memory: 468824k/480256k available (3506k kernel code, 11432k reserved, 852k data, 2600k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:8
Estimated CPU frequency: 796.54 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 529.20 BogoMIPS (lpj=2646016)
Mount-cache hash table entries: 512
devtmpfs: initialized
NET: Registered protocol family 16
prom_flashsize = 0x100000000
Flash size is 0x2000000
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource MIPS-DMP
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Switched to NOHz mode on CPU #0
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.




 *****************    se init module  *********************



se init module major number = 253




 *****************    md init module  *********************



md init module major number = 252
size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52...
init_vdso successfull
rtktlb: Hello, Realtek TLB Mapper...
   AllocBP size: 688128 order: 8 offset: 0
   <<<DVR FREE AREA>>>
   0:   0
   1:   0
   2:   0
   3:   0
   4:   0
   5:   0
   6:   0
   7:   0
   8:   0
   9:   0
   10:   0
   11:   0
   12:   0
   13:   7
      Addr: 82000000, order: 13
      Addr: 84000000, order: 13
      Addr: 86000000, order: 13
      Addr: 88000000, order: 13
      Addr: 8a000000, order: 13
      Addr: 8c000000, order: 13
      Addr: 8e000000, order: 13
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 915
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Realtek Bulid-In SATA Driver Rev:SATURN (2011-02-24 15:10)
sata_rtk sata_rtk: version 0.01
sata_rtk sata_rtk: slots 32 ports 1
scsi0 : sata_rtk
ata1: SATA max UDMA/133 irq 4
BGA PackageRealtek NAND Flash Driver Rev:337905 (2010-10-18)
(X)Enable interrupt mechanism of NAND driver.
Get parameter from register...
[rtk_nand_init]Bootcode size 0x3200000
[rtk_nand_init]Factory parameter size 0x400000
[rtk_nand_init]Disable NFCP...
nand_base_rtk version:0824-2011
(X)NAND_POWEROFF_CARDREADER_WITH_MULTI_READ
(X)NAND_READ_SKIP_UPDATE_BBT
Detect H27UBG8T2B and enable read-retrial mode...
Enable Read-retrial mode...
Enable Randomized mechanism
READ ID:0xad 0xd7 0x94 0xda 0x74 0xc3
One H27UBG8T2B chip has 1 die(s) on board
nand part=H27UBG8T2B, id=add794da, device_size=4294967296, chip_size=4294967296, num_chips=1, page_size=8192, isLastPage=1, eccBits=24
[rtk_nand_scan_bbt] have created bbt B1, just loads it !!
[dump_BBT] Nand BBT Content
[0] (0, 27, 0, 2047)
RTK: using the whole nand as a partitoin
[rtk_nand_init]Randomized enabled
 [rtk_nand_init]Ecc bit select 24
Realtek Nand Flash Driver is successfully installing.
VenusSFC MTD init...
NOR flash support list ..
(X) HWSEMA support.
(V) AUTO_HW_POLL support.
(X) 4Bytes mode support.
(V) Max erase size support.
(V) Sfc_delay support.
[venus_sfc_init]FLASH_BASE: 0xbdc00000
[venus_sfc_init]Flash size: 0x2000000
Read id orginal value : 0xc22015c2
--RDID Seq: 0xc2 | 0x20 | 0x15
VenusSFC MTD: MXIC MX25L1605 detected.
SFC_4KB_ERASE
VenusSFC MTD: Enable VenusSFC MD PP callback function.
MD_READ Enable..
MD_WRITE Enable..
[venus_sfc_init]descriptor size 0x2000000
RedBoot partition parsing not available
Venus SFC: using single partition Venus SFC: (for SST/SPANSION/MXIC SPI Flash)
this  Jupiter eth RX_OFFSET = 0x0
8139cplus: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
MAC address = 0x00.CE.39.BD.37.BA
eth0: RTL-8139C+ at 0xb8016000, 00:ce:39:bd:37:ba, IRQ 2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(861) 0xb8013808 = 0x4400a081
#@# cfyeh-debug USBPHY_Register_Setting(863) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(933)
#@#[cfyeh-debug] USBPHY_Register_Setting(935)
#@#[cfyeh-debug] USBPHY_Register_Setting(937)
#@# cfyeh-debug USBPHY_SetReg_Default_39(289) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ehci ehci: Rtk Dmp EHCI
ehci ehci: new USB bus registered, assigned bus number 1
ehci ehci: irq 2, io mem 0xb8013000
Hotplcp_hotplug
ug got one Net Hotplug of "Add" from "eth0". It may be Realtek's wireless device.
ehci ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[usb_param] setting for saturn
#@# cfyeh-debug USBPHY_Register_Setting(861) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_Register_Setting(863) 0xb8013808 = 0x4400a080
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 1 dr 7
#@# cfyeh-debug USBPHY_SetReg_Default_33_port(210) port 2 dr 7
#@#[cfyeh-debug] USBPHY_Register_Setting(933)
#@#[cfyeh-debug] USBPHY_Register_Setting(935)
#@#[cfyeh-debug] USBPHY_Register_Setting(937)
#@# cfyeh-debug USBPHY_SetReg_Default_39(289) tx_delay 2
[usb1_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb1_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb1_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb1_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
[usb2_param] usbphy reg 32, set sh = 0xa, get sh = 0xa, 4bit
[usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit
[usb2_param] usbphy reg 36, set senh = 0xa, get senh = 0xa, 4bit
[usb2_param] usbphy reg 32, set sen = 0x9, get sen = 0x9, 4bit
[usb2_param] usbphy reg 33, set dr = 0x7, get dr = 0x7, 3bit
ohci ohci: Rtk Dmp OHCI
ohci ohci: new USB bus registered, assigned bus number 2
ohci ohci: irq 2, io mem 0xb8013400
ata1: SATA link down (SStatus 0 SControl 300)
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
#@# cfyeh-debug usb3_phy_setting_saturn(38) +++
#@# cfyeh-debug usb3_phy_setting_saturn(227) ---
xhci xhci: Rtk Dmp XHCI
xhci xhci: new USB bus registered, assigned bus number 3
xhci xhci: irq 2, io mem 0xb8020000
#@# cfyeh-debug xhci_irq(1747) 0x000002a0 0x002802a0
#@# cfyeh-debug handle_port_status(1096) 0x000002a0 0x002802a0
#@#[cfyeh-debug] handle_port_status(1124) NOT in U0
usb usb3: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
#@# cfyeh-debug xhci_hub_control(287) hack for usb3 portsc
#@# cfyeh-debug usb3_mac_setting_saturn(232) +++
#@# cfyeh-debug usb3_mac_setting_saturn(253) 16bit
#@# cfyeh-debug usb3_mac_setting_saturn(254) *(unsigned int volatile *)0xb8028200=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(255) *(unsigned int volatile *)0xb8028200=0x2440
#@# cfyeh-debug usb3_mac_setting_saturn(257) *(unsigned int volatile *)0xb8028200=0x2400
#@# cfyeh-debug usb3_mac_setting_saturn(268) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(270) 0xb8013258 = 0x7;
#@# cfyeh-debug usb3_mac_setting_saturn(274) GTXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(275) 0xb8028108 = 0x02400008
#@# cfyeh-debug usb3_mac_setting_saturn(280) 0xb8028108 = 0x21010000
#@# cfyeh-debug usb3_mac_setting_saturn(283) GRXTHRCFG
#@# cfyeh-debug usb3_mac_setting_saturn(284) 0xb802810c = 0x02000008
#@# cfyeh-debug usb3_mac_setting_saturn(289) 0xb802810c = 0x21080000
#@# cfyeh-debug usb3_mac_setting_saturn(294) disable usb mulit request
#@# cfyeh-debug usb3_mac_setting_saturn(295) *(unsigned int volatile *)0xb8013200=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(297) *(unsigned int volatile *)0xb8013200=0x0
#@# cfyeh-debug usb3_mac_setting_saturn(302) GUSB3PIPECTL
#@# cfyeh-debug usb3_mac_setting_saturn(303) 0xb80282c0 = 0x00060002
#@# cfyeh-debug usb3_mac_setting_saturn(306) 0xb80282c0 = 0x00060202
#@# cfyeh-debug usb3_mac_setting_saturn(309) ---
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
[I2C0] i2c speed changed to 100 KHz
I2C0 Bus Status Check.... OK
=========================
= VER : 2.1b               
=========================
= PHY : 0               
= MODEL: Saturn             
= SPD : 100               
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32     
= RX FIFO DEPTH : 32     
= FIFO THRESHOLD: 4     
= BUS JAM RECORVER 3: ON 
= NON STOP WRITE : ON 
= GPIO RW SUPPORT : ON
=========================
[I2C1] i2c speed changed to 100 KHz
I2C1 Bus Status Check.... OK
=========================
= VER : 2.1b               
=========================
= PHY : 1               
= MODEL: Saturn             
= SPD : 100               
= SAR : 0x024 (7 bits)
= TX FIFO DEPTH : 32     
= RX FIFO DEPTH : 32     
= FIFO THRESHOLD: 4     
= BUS JAM RECORVER 3: ON 
= NON STOP WRITE : ON 
= GPIO RW SUPPORT : ON
=========================
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Hotplug got one Net Hotplug of "Add" from "sit0". It may be Realtek's wireless device.
cp_open
alloc rings cp->rxdesc_buf =0xb82f9000 , cp->ring_dma=0x182f9000
init_hw

 eth0: Set multicast.
jupiter/saturn 1g
init_hw finished

 eth0: Set multicast.

 eth0: Set multicast.

 eth0: Set multicast.
ADDRCONF(NETDEV_UP): eth0: link is not ready
IP-Config: Complete:
     device=eth0, addr=192.168.0.9, mask=255.0.0.0, gw=192.168.0.254,
     host=192.168.0.9, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
Freeing prom memory: 896k freed
Freeing unused kernel memory: 2600k freed
Welcome to Realtek Rescue Linux for PhotoViewer
/etc/init.d/rcS: line 49: cannot create /sys/bus/usb/devices/usb1/bEnableHubOnBoard_woone: nonexistent directory
mount: mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: No such device
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such file or directory
mount: mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: No such device

Please press Enter to activate this console. #@#[cfyeh-debug] check_boot_code_size(1085) nand_boot_size 0x3200000
#@#[cfyeh-debug] check_boot_code_size(1091) factory_size 0x400000

>>>>>> loader start! (Dec  4 2013:13:08:04, version=00.01.01)
#@#[cfyeh-debug] check_boot_code_size(1085) nand_boot_size 0x3200000
#@#[cfyeh-debug] check_boot_code_size(1091) factory_size 0x400000
get_mtd_block_name(/dev/mtdblock0)
[JH] checksignatue(), open(/dev/mtdblock0) nand_boot_size(0x3200000) factory_size(0x400000)
fail 4, sig(W›b¹)
no IMG_XXXX signature found
BUS_TYPE = (null)
Hotplug: device "ram0" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram2" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram3" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram4" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram5" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram7" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram8" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram9" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram1" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram6" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram10" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram11" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram12" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram13" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram14" is skipped.
BUS_TYPE = (null)
Hotplug: device "ram15" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop3" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop5" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop6" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop7" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop0" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop2" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock0" is skipped.
BUS_TYPE = (null)
Hotplug: device "mtdblock1" is skipped.
BUS_TYPE = (null)
Hotplug: device "loop4" is skipped.

насколько я понял, основная проблема это

Code: Select all
fail 4, sig(W›b¹)
no IMG_XXXX signature found


но как это лечить понятия не имею. Смотрел форумы, вроде писали про bootcode.
Подскажите, что в данной ситуации делать? Хотелось бы восстановить и в дальнейшем установить кастомную прошивку.
IconBIT XDS1003DW (v10.1.1.r11337)
pepelats
 
Posts: 4
Joined: 29 Jan 2016, 06:28

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby FarVoice » 06 Feb 2016, 19:56

pepelats wrote:На дисплее NUPGRADE, через USB проходит обновление, но не помогает

Вот как раз лог этого процесса и хотелось бы увидеть
То, что вы выложили - это загрузка рески и ожидание флешки с install.img
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8573
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby pepelats » 06 Feb 2016, 20:22

(cut) overquoting! Пункт 4.19 Правил форума!

Снял логи при обновлении с USB:
Они длинные, в сообщение не влазят, поэтому ссылка на файл.

http://emb.tom.ru:5000/fbsharing/EMZ31gU0

P.S. Забыл написать что у меня модель плеера IconBit XDS1003DW
IconBIT XDS1003DW (v10.1.1.r11337)
pepelats
 
Posts: 4
Joined: 29 Jan 2016, 06:28

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby Pokrass » 06 Feb 2016, 20:24

Для начала оформите подпись viewtopic.php?f=30&t=1036! и это (равно как и оверквотинг) явно описано в Правилах форума п. 2.2.
IconBIT HDS7L Fw: AMP_r12 GUI: VRT
iNeXT HD1 W Fw: X3D_Series_V4.0.2b160406
User avatar
Pokrass
 
Posts: 3134
Joined: 18 Mar 2012, 04:18
Location: Плюк. Планета № 215 в Тентуре галактики "Кин-дза-дза" в Спирали.

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby FarVoice » 06 Feb 2016, 20:33

ну вот. 27 блок флеша запилен
Code: Select all
[dump_BBT] Nand BBT Content
[0] (0, 27, 0, 2047)

...

Begin:[H27UBG8T2B][20202020 20 20]
[20202020 20 20]
[20202020 20 20]
blk_state_len =0x19
get original param in block b, size 0x520
.../..--- FREE index: 6656 order: 9
..--- FREE index: 6160 order: 4
......--- FREE index: 7168 order: 10
..--- FREE index: 6272 order: 7
.............................read bootcode from flash failed (0:0x7)
write bootcode failed: -103

Чистите флеш и пытайтесь прошить. Если сообщение не исчезнет - перепаивайте.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8573
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby pepelats » 06 Feb 2016, 20:41

А какой командой можно почистить флэш? Загрузчик лежит отдельно? Не потрется?
IconBIT XDS1003DW (v10.1.1.r11337)
pepelats
 
Posts: 4
Joined: 29 Jan 2016, 06:28

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby Pokrass » 06 Feb 2016, 20:52

viewtopic.php?f=14&t=13&p=59063#p59063 Примерно так. Поиск по форуму рулит!
И повторюсь, оформите подпись, прежде чем задавать вопросы!
IconBIT HDS7L Fw: AMP_r12 GUI: VRT
iNeXT HD1 W Fw: X3D_Series_V4.0.2b160406
User avatar
Pokrass
 
Posts: 3134
Joined: 18 Mar 2012, 04:18
Location: Плюк. Планета № 215 в Тентуре галактики "Кин-дза-дза" в Спирали.

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby lymax » 07 Feb 2016, 01:14

попробуйте сначала так - хуже не будет
http://moservices.org/forum/viewtopic.p ... 721#p72072
если не получится - тогда без кабеля не обойтись (ссылка в посте выше)
Марсы: 2*Emtec Movie Cube S800H (amp_r12 vrtn + amp_r12 noGUI[NFS/Samba/FTP/Trans])
Сатурны: Iconbit XDS73D + eGreat R6S Pro (ампс + скин 3Dgui)
+ eGreat R6S Pro (ампс ногуй) + 2*eGreat R6S для тестов
Сеть/Инет: LAN / WLAN 300Mb / ADSL 16Mb
User avatar
lymax
 
Posts: 243
Joined: 12 Jun 2012, 00:10

Re: восстановление при самой неудачной прошивке saturn(1186)

Postby pepelats » 07 Feb 2016, 06:13

По методу lymax у меня че то не завелось, поэтому сделал по способу с flash_erase взятого из install.img.
После стирания и переустановки прошивки, плеер ожил :D

Спасибо всем за помощь!

Теперь, войдя во вкус, ;) хотелось бы попробовать какую нить кастомную прошивку, т.к. от оригинальной я не в восторге. Что можете посоветовать? Плеер используется для проигрывания контента с сети: DLNA и внешние приложения. Жесткий диск не установлен. Желательно с ссылкой на инструкцию по установке, чтобы тут не мучить вопросами.
IconBIT XDS1003DW (v10.1.1.r11337)
pepelats
 
Posts: 4
Joined: 29 Jan 2016, 06:28

PreviousNext

Return to Hardware

Who is online

Users browsing this forum: No registered users and 1 guest