moServices

by **maxim74** » 11 Nov 2012, 10:59

Code: Select all: ?hello world! 52805 w2a80i wtaiA~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A ~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A~A[HDMI]: Set I2C Speed = 100 kHz [HDMI]: Chk_HotPlug() TV is not connected. [HDMI]: Read_EDID abort, HDMI cable plug off. [HDMI]: TV is not connected. PAL logo REALTEK ROM Monitor, Revision noon.0202.0023. Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved. For a list of available commands, type Flash memory size = 128 MByte SDRAM size = 128 MByte First free SDRAM address = 0x800fa700 Press 'ESC' to Monitor mode Signature( ) error! Entering rescue linux... Rescue kernel in FLASH, total size seg.1 addr 0xa0a05398, size = 0xf624a seg.2 addr 0x0, size = 0x0 copy rescue0: from a0a05398 to 81000000, len = f624a decompressing rescue: from 81000000 to 80100000: size = f624a lzma finished decompressing rescue done go 0x80100000 Reset Ethernet Mac. Address = 0x80100000 Realtek LINUX (DC ALIAS) started... Venus setting: ROSs have 2621440 bytes RAM. System CPU has 1 UART. System CPU uses external timer interrupt. Bootloader version: noon.0202.0023. This . The information of this board: Company ID:0x0 CPU ID: 0x12 Board I D: 0x202 Ethernet Mac address: 00.11.22.cf.ff.ff Model Config length=0 Base year of RTC is 2010. Config serial console: console=ttyS0,115200n8r prom_flashsize = 0x08000000 Linux version 2.6.12.6-VENUS (alan@localhost.localdomain) (gcc version 3.4.4 mip ssde-6.03.01-20051114) #41 Thu Apr 22 17:21:57 CST 2010 ************************************************************** You didn't specify audio image address, use def ************************************************************** audio addr: 0 CPU revision is: 00019378 Determined physical RAM map: memory: 00100000 @ 00000000 (usable) memory: 002bc000 @ 00100000 (reserved) memory: 019c4000 @ 003bc000 (usable) memory: 00280000 @ 01d80000 (reserved) memory: 06000000 @ 02000000 (usable) show info: max_low_pfn:32768 show info: min_low_pfn:956 Built 1 zonelists Kernel command line: console=ttyS0,115200n8r ip=192.168.0.9::192.168.0.254:255. 0.0.0::: Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled PID hash table entries: 256 (order: 8, 4096 bytes) Estimate value: CPU frequency 405.02 MHz Using 27.000 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 123532k/125712k available (1981k kernel code, 2112k reserved, 302k data, 436k init, 0k highmem) Warning! Unknown board id. Warning! Unknown board id. ==================== Warning! The calculated loops_per_jiffy is not similar to t he default one. ==================== Mount-cache hash table entries: 512 Checking for 'wait' instruction... available. Linux NoNET1.0 for Linux 2.6 SCSI subsystem initialized usbcore: registered new driver hub se init module major number = 254 size of RPC_POLL_Dev 52 and RPC_INTR_Dev 52... Hello, Realtek TLB Mapper AllocBP size: 294912 order: 7 <<<DVR FREE AREA>>> 0: 0 1: 0 2: 0 3: 0 4: 0 5: 0 6: 0 7: 0 8: 0 9: 0 10: 0 11: 0 12: 6 devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 NTFS driver 2.1.28 [Flags: R/O]. Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing enabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A io scheduler noop registered RAMDISK driver initialized: 1 RAM disks of 128K size 1024 blocksize loop: loaded (max 8 devices) Mars no support IDE ide generic info: ide_generic_init Mars no support IDE libata version 1.12 loaded. sata driver initial...2009/12/30 14:50 mars_init_sata(1255)dev_ ata_device_add(4891)probe begin scsi0 : SATA_DRV sata dma reset sata1: reset phy again! sata phy reset sata1: reset phy again! sata phy reset sata1: reset phy extra! sata phy reset sata1: reset phy extra! sata phy reset sata1: reset phy extra! sata phy reset sata1: phy reset timeout! sata1: no device found (phy stat 00000000) sata1: ata_bus_probe failed scsi1 : SATA_DRV sata dma reset sata2: reset phy again! sata phy reset sata2: reset phy again! sata phy reset sata2: phy reset timeout! sata2: no device found (phy stat sata2: ata_bus_probe failed VenusSFC MTD init serial flash inaccessible physmap flash device: 8000000 at 17d00000 Realtek NAND Flash Driver Rev:305341 (2010-04-13) One HY27UF081G2A chip has 1 die(s) on board nand part=HY27UF081G2A, id=adf1801d, device_size=134217728, chip_size=134217728, num_chips=1, isLastPage=0 [NF_CKSEL] HY27UF081G2A is set to nf clock: 0x3 [rtk_nand_scan_bbt] have created bbt B0, just loads it !! [dump_BBT] Nand BBT Content Congratulation!! No BBs in this Nand. RTK: using the whole nand as a Realtek Nand Flash Driver is successfully installing. [usb_param] setting for mars Setting for MARS-B [usb_param] set port two for host! [usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit [usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit [usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit [usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit [usb1_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit [usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit [usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit [usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit [usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit [usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit ehci_hcd ehci_hcd: EHCI Host Controller ehci_hcd ehci_hcd: new USB bus registered, assigned bus number 1 ehci_hcd ehci_hcd: irq 2, io mem 0xb8013000 ehci_hcd ehci_hcd: park 0 ehci_hcd ehci_hcd: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub hub 1-0:1.0: 2 ports detected hub : individual port power switching hub : individual port over-current protection [cfyeh] set PPE = 0 [usb_param] setting for mars Setting for MARS-B [usb_param] set port two for host! [usb1_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit [usb1_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit [usb1_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit [usb1_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit [usb1_param] usbphy reg 33, set dr = 0x0, get dr [usb2_param] usbphy reg 32, set sh = 0x5, get sh = 0x5, 4bit [usb2_param] usbphy reg 35, set src = 0x7, get src = 0x7, 3bit [usb2_param] usbphy reg 36, set senh = 0xd, get senh = 0xd, 4bit [usb2_param] usbphy reg 32, set sen = 0x8, get sen = 0x8, 4bit [usb2_param] usbphy reg 33, set dr = 0x0, get dr = 0x0, 3bit ohci_hcd ohci_hcd: OHCI Host Controller ohci_hcd ohci_hcd: new USB bus registered, assigned bus number 2 ohci_hcd ohci_hcd: irq 2, io mem 0xb8013400 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detecte hub : no power switching (usb 1.0) hub : no over-current protection ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) Initializing USB Mass Storage driver... ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -14 hub 1-0:1.0: hub_port_status failed (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -14 hub 1-0:1.0: hub_port_status failed (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -145 hub 1-0:1.0: hub_port_status failed (err = -32) ehci_hcd ehci_hcd: port 1 reset error -14 hub 1-0:1.0: hub_port_status failed (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? usbcore: registered new driver usb-storage USB Mass Storage support registered. Setting registers , Enable OTG dwc_otg: version 2.60a 22-NOV-2006 DWC_otg: Shared Tx FIFO mode i2c /dev entries driver [I2C0] i2c speed changed to 100 KHz I2C0 Bus Status Check.... OK ========================= = VER : 2.0a ========================= DWC_otg: USB RESET = PHY : 0 = MODE: MARS = SPD : 100 = SAR : 0x024 (7 bits) = TX FIFO DEPTH : 8 = RX FIFO DEPTH : 8 = FIFO THRESHOLD: 4 = BUS JAM RECORVER : ON = NON STOP WRITE : OFF = SP PROTECT : ON ========================= FATAL : I2C 1 pins have been occupied by PCI Trying to free free IRQ3 Freeing prom memory: 0kb freed Reclaim bootloader memory from 80020000 to 80100000 Freeing unused kernel memory: 436k freed init started: BusyBox v1.1.3 (2010.04.22-09:20+0000) multi-call binary Starting pid 334, console /dev/console: '/etc/init.d/rcS' 120+0 records in 120+0 records out Welcome to Realtek Rescue Linux for PhotoViewer mount: Mounting /dev/cdroms/cdrom0 on /mnt/usbmounts/cdrom failed: Unknown error 19 mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2 mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2 mount: Mounting /dev/hda1 on /mnt/usbmounts/hda1 failed: Unknown error 2 >>>>>> loader start! (Apr 22 2010:17:21:29, version=00.01.01) Secure Boot is off. Please press Enter to activate this console. Hotplug: device "ram0" is skipped. Hotplug: device "loop0" is skipped. Hotplug: device "loop1" is skipped. Hotplug: device "loop2" is skipped. Hotplug: device "loop3" is skipped. Hotplug: device "loop4" is skipped. Hotplug: device "loop5" is skipped. Hotplug: device "loop6" is skipped. Hotplug: device "loop7" is skipped. Hotplug: device "mtdblock0" is skipped. Secure Boot is off. Secure Boot is off. Secure Boot is off.

by **Virtual** » 11 Nov 2012, 11:52

1. своими манипуляциями вы стерли не только прошивку но и бутпараметры! придется в RomMonitor восстанавливать MAC адрес
2. т.к. прошивки нет то плеер в реску

и ждет прошивку (пишем в корень носителя install.img и отдаем плееру)
3. есть вероятность что usb поврежден.... (если не сожрет прошивку с USB) тогда придется пхать ее на SATA диске.

PS ну и не забываем логи писать.

PSPS я вам уже грил что USB скончался! по логу видно что смена буткода не помогла...
а так же вам дал альтернативное ядро! с сетью.... с его помощью можно легко скачать NoBin прошивку прям в оперативку плеера и установить!.

by **Virtual** » 11 Nov 2012, 12:34

вот так ставится NoBin прошивка по сети:
1. не забываем запустить на компе tftp сервер и в него положить vmlinux.bin (предварительно скачаный тюнинговый rescu образ.)

Realtek> set ipaddr 192.168.0.2
Realtek> set gateway 192.168.0.1
Realtek> set subnetmask 255.255.255.0
Realtek> fread tftp://192.168.0.7/vmlinux.bin 0x80100000

About to binary read tftp://192.168.0.7/vmlinux.bin

.........Successfully transferred 0x2fb0c2 (10'3125442) bytes

Realtek>

Realtek> go 0x80100000
........
попили чаю и т.д. короче дождались пока rescu прогрузится полностью
мочим лоадер!
~ # killall loader_a
убедились что замочили
~ # ps
создадим папочку где лоадер найдет нужное
~ # mkdir /tmp/usbmounts/sda1 -p
~ #
~ # sync
проверяем размер свободной оперативы!
~ # cat /proc/meminfo
MemTotal: 124636 kB
MemFree: 119612 kB
~ #
качаем прошивку что влезет в оперативную память, и желательно чтоб и свободно осталось .
~ # wget ........install.img -O /tmp/usbmounts/sda1/install.img
Connecting to .............
убедились что она скачалась вся, и размер совпадает
ls -l /tmp/usbmounts/sda1/
-rw-r--r-- 1 root 0 53608448 Nov 11 14:19 install.img
~ #
запускаем лоадер он сам найдет прошивку и поставит
~ # loader_a

ps на текущий час доступна безскиновая версия http://www.moservices.org/files/amp_r7_mos.zip (53,567,488 байтов)
если что будет доступно позже смотреть тут:
viewtopic.php?f=8&t=1029

by **maxim74** » 11 Nov 2012, 14:54

настроил терминал на висте,
ip рутера y меня 192.168.1.1
ip компа пробывал 192.168.1.7 и 192.168.1.53
настроил программу TFTPD32, добыл vmlinux.bin

вот такая беда:

Realtek> set ipaddr 192.168.1.2
Realtek> set gateway 192.168.1.1
Realtek> set subnetmask 255.255.255.0
Realtek> fread tftp://192.168.1.53/vmlinux.bin 0x80100000
About to binary read tftp://192.168.1.53/vmlinux.bin

Error : ARP-timeout, no reponse on ARP-request
Hint : Check cable and IP-address of remote host

by **Virtual** » 11 Nov 2012, 16:38

жестко пишет что не видит 192.168.1.53
!!!
иль эзернет кабель в плеер не воткнут иль у компа не такой IP иль еще чего.

by **maxim74** » 11 Nov 2012, 17:12

дело не в кабеле, 2 разных цеплял.

думаю в tftp не разобрался.

какую прогу лучше брать и как настроить?

by **Virtual** » 11 Nov 2012, 17:38

viewtopic.php?f=8&t=79
пункты от 2 до 4.1 ваши.
но с семеркой есть свои грабли

... но борьбу с ними оставлю вам.

ЗЫ
Error : ARP-timeout, no reponse on ARP-request
обычно говорит что IP адрес не резольвится

PSPS буткод менялся по сериальному шнурку или через tftp ?
//если выяснится что и сеть не пашет :mrgreen:

., вам прямая дорога чинить питание.
//проверено на практике! если кончается электричество.... первым падает USB, вторым ETH

by **maxim74** » 13 Nov 2012, 00:27

блин перепутал вся это поставил в место

fread tftp://192.168.0.1/boot.bin 0x80100000
go 0x80100000

теперь не грузит с tftp

######################################################

REALTEK ROM Monitor, Revision 0001.0203.0026.
Copyright (c) Realtek Semiconductor Corp. - All Rights Reserved.

For a list of available commands, type 'help'.

Compilation time /version= Aug 26 2010 17:25:18 /0001.0203.0026
MAC address = 00.11.22.33.44.55
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0x93 / 0x78
Endianness = Little
Flash memory size = 128 MByte
SDRAM size = 128 MByte
First free SDRAM address = 0x800fcc00

USB slave cable detected
Press 'ESC' to Monitor mode
Realtek> fread tftp://192.168.1.7/vmlinux.bin 0x80100000
About to binary read tftp://192.168.1.7/vmlinux.bin

###########################################################

вот так менут 10 ждал ничего не происходит

что теперь хана?

by **Virtual** » 13 Nov 2012, 04:47

в логе tftp сервера на компе есть то что плеер обращается?

PS с семеркой не все так просто.... часто файрвол блокирует работу сервера tftp

by **maxim74** » 13 Nov 2012, 08:17

нет в логе пусто, до этого всё шло, стояло "sending file" что ли.

делаю теперь на висте на другом компе,

до

fread tftp://192.168.0.1/boot.bin 0x80100000
go 0x80100000

всё шло

а сейчас тормозит

moServices

Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Re: Poppstrar MS 30

Who is online