Beta from HD2 - for englishmen

[FarVoice]

Thanks for that link. I'm on bootcode 17, & as I bricked my player by trying to install Jarre's original file (I should have waited to see your comment ) & then had to find my serial cable, I had better wait until a more recent version
John

Another good news And in Russian again viewtopic.php?f=8&t=65

[Jarre]

Another good news And in Russian again viewtopic.php?f=8&t=65

make this in english please, so i can update to the new bootcode too....tou know wht the chbged in there..???

[FarVoice]

make this in english please, so i can update to the new bootcode too....tou know wht the chbged in there..???

I did it viewtopic.php?f=12&t=78&start=0

[Jarre]

make this in english please, so i can update to the new bootcode too....tou know wht the chbged in there..???

I did it viewtopic.php?f=12&t=78&start=0

thanks, do you know already what they check in ceretification FW..????

please explain the serial cable part...where i have to get it, and what..????

[FarVoice]

thanks, do you know already what they check in certification FW..????

please explain the serial cable part...where i have to get it, and what..????

I guess. In bootcode 23 presents the AES key. May be it puts to I2C chip?

About handmade serial cable http://www.patriotmem.com/forums/showthread.php?t=3479
or buy on eBay http://shop.ebay.com/?_from=R40&_trksid ... Categories

[Jarre]

thanks, do you know already what they check in certification FW..????

please explain the serial cable part...where i have to get it, and what..????

I guess. In bootcode 23 presents the AES key. May be it puts to I2C chip?

About handmade serial cable http://www.patriotmem.com/forums/showthread.php?t=3479
or buy on eBay http://shop.ebay.com/?_from=R40&_trksid ... Categories

how to hook up the oplay..???

[john]

Look at the pictures in the minimodding link I posted for you.

You need to remove the covers from O!Play (easy to do) to reveal the component side of the printed circuit board. Adjacent to the heat sink is a 4 pin "header", clearly marked gnd, rx, tx. Ignore the 3 volts power pin.

You connect the respective 3 wires from your serial cable to that header & follow the instructions to use the cable.

[Jon Jon]

Sorry my bad, I meant bootcode 18.

you can safely flash the original FW from Jarre. Through Reset of course

Hi, What do you mean whit this: "Through Reset of course" ??

Should i reflash to some FW before install the HD2?

[FarVoice]

Hi, What do you mean whit this: "Through Reset of course" ??

Emergency Recovery Instructions.

If the O!Play accidentally shut down during the firmware upgrade, the safe mode will enable
the O!Play to be re-upgraded. you can to restart the Safe Mode Upgrade.
Note: Emergency Recovery function only takes effect if your O!Play’s Bootcode Version is
0000.0202.0018 or later. ( Bootcode Version Check method: Press the STOP button.
then PLAY/PAUSE button on the Remote controller. The Version information screen
will be displayed.

Please follow the steps below:

1.While pressing the reset button (The reset button is located on the side panel.
Use a pointed object to press this button), Disconnect DC plug. wait 5 seconds and
reconnect DC plug of the Power adapter.

2.The message will be displayed on the screen as “Preparing for update.
It takes a few seconds”

3. Repeat the procedure of (How to Update the Firmware).Until the upgrade has been
successfully finished.

[sansu]

Hi,

I have boot code: 0202.0017. Firmware 1.33N - R1 Oplay. I downloaded your FW and trying to install it for the past 1 hour with various reset options I read from forms. Still no success. All kind of hard reset comes back to the setup screen only. I tried it thro' the menu and it complained that the FW is not for this board or something. Could someone please tell me how to flash this FW in bootcode 17 box? I really appreciate your help.

[UPDATE] I managed to install it now. I tricked the player into thinking that I am installing a normal FW (found the tip in Asus forum). First impression is nice. Thank you so much for your hard work.


Thanks,