installation after each start up?

installation after each start up?

Postby Tenente » 23 Nov 2012, 20:32

hallo,

I installed the moServices to enable "nas" function of my HDP-R1. It works, however. After switch off O!Play (standby mode) I have to do an installation again. I cannot find any information on forum how to have moServices installed permanently. Please advice, thank you!
O!Play HDP-R1
Official FW 1.40P
Tenente
 
Posts: 3
Joined: 23 Nov 2012, 18:16

Re: installation after each start up?

Postby FarVoice » 23 Nov 2012, 20:39

show me please
Code: Select all
df
cat /proc/mtd
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: installation after each start up?

Postby Tenente » 24 Nov 2012, 10:46

Hallo,
thank you for your reply. The oplay was in standby whole night, this morning I tried to switch on, usb disk plug in to oplay has been accessible via network. So I assumed it was my fault, and moServices are in the oplay. I also tried to do the wake on lan, this works as well. But when I tried the moService manager it can't see it...

Here are the commands outputs.

/ # df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 74496 73396 1100 99% /
/dev/mtdblock/2 61440 9548 51892 16% /usr/local/etc
/dev/rd/0 40 40 0 100% /mnt/rd
/dev/scsi/host4/bus0/target0/lun0/part1 976760000 736253996 240506004 75% /tmp/usbmounts/sda1

/ # cat /proc/mtd
dev: size erasesize name
mtd0: 06e60000 00020000 "Partition_000"
mtd1: 048c0000 00020000 "/"
mtd2: 03c00000 00020000 "/usr/local/etc"
mtd3: 00ce0000 00020000 "Partition_003"
mtd4: 10000000 00020000 "disc"
O!Play HDP-R1
Official FW 1.40P
Tenente
 
Posts: 3
Joined: 23 Nov 2012, 18:16

Re: installation after each start up?

Postby FarVoice » 24 Nov 2012, 16:31

Hmmm... Do you install moS2 or moS3 ?
And please, flash FW from Air (R3) - the fw from R1 is not correct works with network.
ASUS O!Play R1 (amp_r12_vrtn), xTreamer Pro (amp_r12_vrt), xTreamer Prodigy (iNeXT 2.14 r2), IconBIT HDR12L (amp_r12_vrt), 3Q F425HW (xds42gl_7725_r3), MyGica A11 (mygica_m3_20121222)
User avatar
FarVoice
Администратор
 
Posts: 8572
Joined: 03 Sep 2010, 01:27
Location: Russia, Moscow

Re: installation after each start up?

Postby Tenente » 25 Nov 2012, 11:27

I am using just the original FW. Now the SAMBA works well, interesting. For the mos, I used the step by step procedure on your page, download from web (in linux/Venus os), so it means it was moS2.
O!Play HDP-R1
Official FW 1.40P
Tenente
 
Posts: 3
Joined: 23 Nov 2012, 18:16


Return to About moServices

Who is online

Users browsing this forum: No registered users and 14 guests

cron